Simulation of the impact of faults on CO2 injection into sandstone reservoirs

Numerical simulations of multiphase CO₂ behavior within faulted sandstone reservoirs examine the impact of fractures and faults on CO₂ migration in potential subsurface injection systems. In southeastern Utah, some natural CO₂ reservoirs are breached and CO₂‐charged water flows to the surface along permeable damage zones adjacent to faults; in other sites, faulted sandstones form barriers to flow and large CO₂‐filled reservoirs result. These end‐members serve as the guides for our modeling, both at sites where nature offers ‘successful’ storage and at sites where leakage has occurred. We consider two end‐member fault types: low‐permeability faults dominated by deformation‐band networks and high‐permeability faults dominated by fracture networks in damage zones adjacent to clay‐rich gouge. Equivalent permeability (k) values for the fault zones can range from <10^?14 m² for deformation‐band‐dominated faults to >10^?12 m² for fracture‐dominated faults regardless of the permeability of unfaulted sandstone. Water–CO₂ fluid‐flow simulations model the injection of CO₂ into high‐k sandstone (5 × 10^?13 m²) with low‐k (5 × 10^?17 m²) or high‐k (5 × 10^?12 m²) fault zones that correspond to deformation‐band‐ or fracture‐dominated faults, respectively. After 500 days, CO₂ rises to produce an inverted cone of free and dissolved CO₂ that spreads laterally away from the injection well. Free CO₂ fills no more than 41% of the pore space behind the advancing CO₂ front, where dissolved CO₂ is at or near geochemical saturation. The low‐k fault zone exerts the greatest impact on the shape of the advancing CO₂ front and restricts the bulk of the dissolved and free CO₂ to the region upstream of the fault barrier. In the high‐k aquifer, the high‐k fault zone exerts a small influence on the shape of the advancing CO₂ front. We also model stacked reservoir seal pairs, and the fracture‐dominated fault acts as a vertical bypass, allowing upward movement of CO₂ into overlying strata. High‐permeability fault zones are important pathways for CO₂ to bypass unfaulted sandstone, which leads to reduce sequestration efficiency. Aquifer compartmentalization by low‐permeability fault barriers leads to improved storativity because the barriers restrict lateral CO₂ migration and maximize the volume and pressure of CO₂ that might be emplaced in each fault‐bound compartment. As much as a 3.5‐MPa pressure increase may develop in the injected reservoir in this model domain, which under certain conditions may lead to pressures close to the fracture pressure of the top seal.     

The upper continental crust, an aquifer and its fluid: hydaulic and chemical data from 4 km depth in fractured crystalline basement rocks at the KTB test site

Detailed information on the hydrogeologic and hydraulic properties of the deeper parts of the upper continental crust is scarce. The pilot hole of the deep research drillhole (KTB) in crystalline basement of central Germany provided access to the crust for an exceptional pumping experiment of 1‐year duration. The hydraulic properties of fractured crystalline rocks at 4 km depth were derived from the well test and a total of 23100 m³ of saline fluid was pumped from the crustal reservoir. The experiment shows that the water‐saturated fracture pore space of the brittle upper crust is highly connected, hence, the continental upper crust is an aquifer. The pressure–time data from the well tests showed three distinct flow periods: the first period relates to wellbore storage and skin effects, the second flow period shows the typical characteristics of the homogeneous isotropic basement rock aquifer and the third flow period relates to the influence of a distant hydraulic border, probably an effect of the Franconian lineament, a steep dipping major thrust fault known from surface geology. The data analysis provided a transmissivity of the pumped aquifer T = 6.1 × 10^?6 m² sec^?1, the corresponding hydraulic conductivity (permeability) is K = 4.07 × 10^?8 m sec^?1 and the computed storage coefficient (storativity) of the aquifer of about S = 5 × 10^?6. This unexpected high permeability of the continental upper crust is well within the conditions of possible advective flow. The average flow porosity of the fractured basement aquifer is 0.6–0.7% and this range can be taken as a representative and characteristic values for the continental upper crust in general. The chemical composition of the pumped fluid was nearly constant during the 1‐year test. The total of dissolved solids amounts to 62 g l^?1 and comprise mainly a mixture of CaCl₂ and NaCl; all other dissolved components amount to about 2 g l^?1. The cation proportions of the fluid (X_Ca approximately 0.6) reflects the mineralogical composition of the reservoir rock and the high salinity results from desiccation (H₂O‐loss) due to the formation of abundant hydrate minerals during water–rock interaction. The constant fluid composition suggests that the fluid has been pumped from a rather homogeneous reservoir lithology dominated by metagabbros and amphibolites containing abundant Ca‐rich plagioclase.     

Analytical and numerical models of hydrothermal fluid flow at fault intersections

Fault intersections are the locus of hot spring activity and Carlin‐type gold mineralization within the Basin and Range, USA. Analytical and numerical solutions to Stokes equation suggest that peak fluid velocities at fault intersections increase between 20% and 47% when fracture apertures have identical widths but increase by only about 1% and 8% when aperture widths vary by a factor of 2. This suggests that fault zone intersections must have enlarged apertures. Three‐dimensional finite element models that consider intersecting 10‐ to 20‐m wide fault planes resulted in hot spring activity being preferentially located at fault zone intersections when fault zones were assigned identical permeabilities. We found that the onset of convection at the intersections of the fault zones occurred in our hydrothermal model over a narrow permeability range between 5 × 10^?13 and 7 × 10^?13 m². Relatively high vertical fluid velocities (0.3–3 m year^?1) extended away from the fault intersections for about 0.5–1.5 km. For the boundary conditions and fault plane dimensions used, peak discharge temperatures of 112°C at the water table occurred with an intermediate fault zone permeability of 5 × 10^?13 m². When fault plane permeability differed by a factor of 2 or more, the locus of hot spring activity shifted away from the intersections. However, increasing the permeability at the core of the fault plane intersection by 40% shifted the discharge back to the intersections. When aquifer units were assigned a permeability value equal to those of the fault planes, convective rolls developed that extend about 3 km laterally along the fault plane and into the adjacent aquifer.     

Hydraulic observations from a 1 year fluid production test in the 4000 m deep KTB pilot borehole

A long‐term pump test was conducted in the KTB pilot borehole (KTB‐VB), located in the Oberpfalz area, Germany. It produced 22 300 m³ of formation fluid. Initially, fluid production rate was 29 l min^?1 for 4 months, but was then raised to an average of 57 l min^?1 for eight more months. The aim of this study was to examine the fluid parameters and hydraulic properties of fractured, crystalline crusts as part of the new KTB programme ‘Energy and Fluid Transport in Continental Fault Systems’. KTB‐VB has an open‐hole section from 3850 to 4000 m depth that is in hydraulic contact with a prominent continental fault system in the area, called SE2. Salinity and temperature of the fluid inside the borehole, and consequently hydrostatic pressure, changed significantly throughout the test. Influence of these quantities on variations in fluid density had to be taken into account for interpretation of the pump test. Modelling of the pressure response related to the pumping was achieved assuming the validity of linear Darcy flow and permeability to be independent of the flow rate. Following the principle ‘minimum in model dimension’, we first examined whether the pressure response can be explained by an equivalent model where rock properties around the borehole are axially symmetric. Calculations show that the observed pressure data in KTB‐VB can in fact be reproduced through such a configuration. For the period of high pumping rate (57 l min^?1) and the following recovery phase, the resulting parameters are 2.4 × 10^?13 m³ in hydraulic transmissivity and 3.7 × 10^?9 m Pa^?1 in storativity for radial distances up to 187 m, and 4.7 × 10^?14 m³ and 6.0 × 10^?9 m Pa^?1, respectively, for radial distances between 187 and 1200 m. The former pair of values mainly reflect the hydraulic properties of the fault zone SE2. For a more realistic hydraulic study on a greater scale, program FEFLOW was used. Parameter values were obtained by matching the calculated induced pressure signal to fluid‐level variations observed in the KTB main hole (KTB‐HB) located at 200 m radial distance from KTB‐VB. KTB‐HB is uncased from 9031 to 9100 m and shows indications of leakage in the casing at depths 5200–5600 m. Analysis of the pressure record and hydraulic modelling suggest the existence of a weak hydraulic communication between the two boreholes, probably at depths around the leakage. Hydraulic modelling of a major slug‐test in KTB‐HB that was run during the pumping in KTB‐VB reveals the effective transmissivity of the connected formation to be 1 to 2 orders of magnitude lower than the one determined for the SE2 fault zone.     

Effects of episodic fluid flow on hydrocarbon migration in the Newport‐Inglewood Fault Zone,Southern California

Fault permeability may vary through time due to tectonic deformations, transients in pore pressure and effective stress, and mineralization associated with water‐rock reactions. Time‐varying permeability will affect subsurface fluid migration rates and patterns of petroleum accumulation in densely faulted sedimentary basins such as those associated with the borderland basins of Southern California. This study explores the petroleum fluid dynamics of this migration. As a multiphase flow and petroleum migration case study on the role of faults, computational models for both episodic and continuous hydrocarbon migration are constructed to investigate large‐scale fluid flow and petroleum accumulation along a northern section of the Newport‐Inglewood fault zone in the Los Angeles basin, Southern California. The numerical code solves the governing equations for oil, water, and heat transport in heterogeneous and anisotropic geologic cross sections but neglects flow in the third dimension for practical applications. Our numerical results suggest that fault permeability and fluid pressure fluctuations are crucial factors for distributing hydrocarbon accumulations associated with fault zones, and they also play important roles in controlling the geologic timing for reservoir filling. Episodic flow appears to enhance hydrocarbon accumulation more strongly by enabling stepwise build‐up in oil saturation in adjacent sedimentary formations due to temporally high pore pressure and high permeability caused by periodic fault rupture. Under assumptions that fault permeability fluctuate within the range of 1–1000 millidarcys (10^?15–10^?12 m²) and fault pressures fluctuate within 10–80% of overpressure ratio, the estimated oil volume in the Inglewood oil field (approximately 450 million barrels oil equivalent) can be accumulated in about 24 000 years, assuming a seismically induced fluid flow event occurs every 2000 years. This episodic petroleum migration model could be more geologically important than a continuous‐flow model, when considering the observed patterns of hydrocarbons and seismically active tectonic setting of the Los Angeles basin.     

Effective gas permeability of Tight Gas Sandstones as a function of capillary pressure – a non‐steady‐state approach

Single‐ and two‐phase (gas/water) fluid transport in tight sandstones has been studied in a series of permeability tests on core plugs of nine tight sandstones of the southern North Sea. Absolute (Klinkenberg‐corrected) gas permeability coefficients (k_gas__inf) ranged between 3.8 × 10^?16 and 6.2 × 10^?19 m² and decreased with increasing confining pressure (10–30 MPa) by a factor 3–5. Klinkenberg‐corrected (intrinsic) gas permeability coefficients were consistently higher by factors from 1.4 to 10 than permeability coefficients determined with water. Non‐steady‐state two‐phase (He/water) flow experiments conducted up to differential pressures of 10 MPa document the dynamically changing conductivity for the gas phase, which is primarily capillary‐controlled (drainage and imbibition). Effective gas permeability coefficients in the two‐phase flow tests ranged between 1.1 × 10^?17 and 2.5 × 10^?22 m², corresponding to relative gas permeabilities of 0.03% and 10%. In the early phase of the nonstationary flow regime (before establishment of steady‐state conditions), they may be substantially (>50%) lower. Effective gas permeability measurements are affected by the following factors: (i) Capillary‐controlled drainage/imbibition, (ii) viscous–dynamic effects (iii) and slip flow.     

Exploring the potential linkages between oil‐field brine reinjection,crystalline basement permeability,and triggered seismicity for the Dagger Draw Oil field,southeastern New Mexico,USA, using hydrologic modeling

We used hydrologic models to explore the potential linkages between oil‐field brine reinjection and increases in earthquake frequency (up to M_d 3.26) in southeastern New Mexico and to assess different injection management scenarios aimed at reducing the risk of triggered seismicity. Our analysis focuses on saline water reinjection into the basal Ellenburger Group beneath the Dagger Draw Oil field, Permian Basin. Increased seismic frequency (>M_d 2) began in 2001, 5 years after peak injection, at an average depth of 11 km within the basement 15 km to the west of the reinjection wells. We considered several scenarios including assigning an effective or bulk permeability value to the crystalline basement, including a conductive fault zone surrounded by tighter crystalline basement rocks, and allowing permeability to decay with depth. We initially adopted a 7 m (0.07 MPa) head increase as the threshold for triggered seismicity. Only two scenarios produced excess heads of 7m five years after peak injection. In the first, a hydraulic diffusivity of 0.1 m² s^?1 was assigned to the crystalline basement. In the second, a hydraulic diffusivity of 0.3 m² s^?1 was assigned to a conductive fault zone. If we had considered a wider range of threshold excess heads to be between 1 and 60 m, then the range of acceptable hydraulic diffusivities would have increased (between 0.1–0.01 m² s^?1 and 1–0.1 m² s^?1 for the bulk and fault zone scenarios, respectively). A permeability–depth decay model would have also satisfied the 5‐year time lag criterion. We also tested several injection management scenarios including redistributing injection volumes between various wells and lowering the total volume of injected fluids. Scenarios that reduced computed excess heads by over 50% within the crystalline basement resulted from reducing the total volume of reinjected fluids by a factor of 2 or more.     

Modelling the Lost City hydrothermal field: influence of topography and permeability structure

The Lost City hydrothermal field (LCHF) is hosted in serpentinite at the crest of the Atlantis Massif, an oceanic core complex close to the mid‐Atlantic Ridge. It is remarkable for its longevity and for venting low‐temperature (40–91°C) alkaline fluids rich in hydrogen and methane. IODP Hole U1309D, 5 km north of the LCHF, penetrated 1415 m of gabbroic rocks and contains a near‐conductive thermal gradient close to 100°C km^?1. This is remarkable so close to an active hydrothermal field. We present hydrothermal modelling using a topographic profile through the vent field and IODP site U1309. Long‐lived circulation with vent temperatures similar to the LCHF can be sustained at moderate permeabilities of 10^?14 to 10^?15 m² with a basal heatflow of 0.22 W m^?2. Seafloor topography is an important control, with vents tending to form and remain in higher topography. Models with a uniform permeability throughout the Massif cannot simultaneously maintain circulation at the LCHF and the near‐conductive gradient in the borehole, where permeabilities <10^?16 m² are required. A steeply dipping permeability discontinuity between the LCHF and the drill hole is required to stabilize venting at the summit of the massif by creating a lateral conductive boundary layer. The discontinuity needs to be close to the vent site, supporting previous inferences that high permeability is most likely produced by faulting related to the transform fault. Rapid increases in modelled fluid temperatures with depth beneath the vent agree with previous estimates of reaction temperature based on geochemical modelling.     

Cyclic loading of an idealized clay‐filled fault: comparing hydraulic flow in two clay gouges

The flow of water along discontinuities, such as fractures or faults, is of paramount importance in understanding the hydrogeology of many geological settings. An experimental study was undertaken comprising two experiments on a 30° slip‐plane filled with kaolinite or Ball Clay gouge using a bespoke Angled Shear Rig (ASR). The gouge was initially loaded in equal step changes in vertical stress, followed by unloading of the sample in similar equal steps. This was followed by reloading to a new maximum stress, followed by unloading; the test history was therefore load‐unload‐reload‐unload (LURU). The transmissivity of the kaolinite and Ball Clay gouge showed a power‐law relationship with vertical stress. The LURU history showed considerable hysteresis, with flow effectively unchanged during unloading, even when vertical stress was close to zero. Reloading resulted in flow similar to that seen during unloading suggesting that the unloading‐reloading path is similar to the rebound‐reconsolidation line in classic soil mechanics. These observations show the importance of stress history on fracture flow; consideration of just the current stress acting upon a fracture may result in inaccuracies of predicted hydraulic flow. Once a new stress maximum was achieved the transmissivity of the fracture continued to reduce. No significant variation was seen in the flow response of kaolinite and Ball Clay gouge suggesting that the inclusion of illite and quartz did not have a significant influence on the form of the relationship between stress and flow, i.e. both described by a power‐law.     

Carbon dioxide controlled earthquake distribution pattern in the NW Bohemian swarm earthquake region,western Eger Rift,Czech Republic – gas migration in the crystalline basement

The ascent of magmatic carbon dioxide in the western Eger (Oh?e) Rift is interlinked with the fault systems of the Variscian basement. In the Cheb Basin, the minimum CO₂ flux is about 160 m³ h^?1, with a diminishing trend towards the north and ceasing in the main epicentral area of the Northwest Bohemian swarm earthquakes. The ascending CO₂ forms Ca‐Mg‐HCO₃ type waters by leaching of cations from the fault planes and creates clay minerals, such as kaolinite, as alteration products on affected fault planes. These mineral reactions result in fault weakness and in hydraulically interconnected fault network. This leads to a decrease in the friction coefficient of the Coulomb failure stress (CFS) and to fault creep as stress build‐up cannot occur in the weak segments. At the transition zone in the north of the Cheb Basin, between areas of weak, fluid conductive faults and areas of locked faults with frictional strength, fluid pressure can increase resulting in stress build‐up. This can trigger strike‐slip swarm earthquakes. Fault creep or movements in weak segments may support a stress build‐up in the transition area by transmitting fluid pressure pulses. Additionally to fluid‐driven triggering models, it is important to consider that fluids ascending along faults are CO₂‐supersaturated thus intensifying the effect of fluid flow. The enforced flow of CO₂‐supersaturated fluids in the transitional zone from high to low permeability segments through narrowings triggers gas exsolution and may generate pressure fluctuations. Phase separation starts according to the phase behaviour of CO₂‐H₂O systems in the seismically active depths of NW Bohemia and may explain the vertical distribution of the seismicity. Changes in the size of the fluid transport channels in the fault systems caused, or superimposed, by fault movements, can produce fluid pressure increases or pulses, which are the precondition for triggering fluid‐induced swarm earthquakes.     

Geometry‐coupled reactive fluid transport at the fracture scale: application to CO2 geologic storage

Water acidification follows CO₂ injection and leads to reactive fluid transport through pores and rock fractures, with potential implications to reservoirs and wells in CO₂ geologic storage and enhanced oil recovery. Kinetic rate laws for dissolution reactions in calcite and anorthite are combined with the Navier‐Stokes law and advection–diffusion transport to perform geometry‐coupled numerical simulations in order to study the evolution of chemical reactions, species concentration, and fracture morphology. Results are summarized as a function of two dimensionless parameters: the Damköhler number Da which is the ratio between advection and reaction times, and the transverse Peclet number Pe defined as the ratio between the time for diffusion across the fracture and the time for advection along the fracture. Reactant species are readily consumed near the inlet in a carbonate reservoir when the flow velocity is low (low transverse Peclet number and Da > 10^?1). At high flow velocities, diffusion fails to homogenize the concentration field across the fracture (high transverse Peclet number Pe > 10^?1). When the reaction rate is low as in anorthite reservoirs (Da < 10^?1), reactant species are more readily transported toward the outlet. At a given Peclet number, a lower Damköhler number causes the flow channel to experience a more uniform aperture enlargement along the length of the fracture. When the length‐to‐aperture ratio is sufficiently large, say l/d > 30, the system response resembles the solution for 1D reactive fluid transport. A decreased length‐to‐aperture ratio slows the diffusive transport of reactant species to the mineral fracture surface, and analyses of fracture networks must take into consideration both the length and slenderness of individual fractures in addition to Pe and Da numbers.     

Stress‐dependent transport properties of fractured arkosic sandstone

We measure the fluid transport properties of microfractures and macrofractures in low‐porosity polyphase sandstone and investigate the controls of in situ stress state on fluid flow conduits in fractured rock. For this study, the permeability and porosity of the Punchbowl Formation sandstone, a hydrothermally altered arkosic sandstone, were measured and mapped in stress space under intact, microfractured, and macrofractured deformation states. In contrast to crystalline and other sedimentary rocks, the distributed intragranular and grain‐boundary microfracturing that precedes macroscopic fracture formation has little effect on the fluid transport properties. The permeability and porosity of microfractured and intact sandstone depend strongly on mean stress and are relatively insensitive to differential stress and proximity to the frictional sliding envelope. Porosity variations occur by elastic pore closure with intergranular sliding and pore collapse caused by microfracturing along weakly cemented grain contacts. The macroscopic fractured samples are best described as a two‐component system consisting (i) a tabular fracture with a 0.5‐mm‐thick gouge zone bounded by 1 mm thick zones of concentrated transgranular and intragranular microfractures and (ii) damaged sandstone. Using bulk porosity and permeability measurements and finite element methods models, we show that the tabular fracture is at least two orders of magnitude more permeable than the host rock at mean stresses up to 90 MPa. Further, we show that the tabular fracture zone dilates as the stress state approaches the friction envelope resulting in up to a three order of magnitude increase in fracture permeability. These results indicate that the enhanced and stress‐sensitive permeability in fault damage zones and sedimentary basins composed of arkosic sandstones will be controlled by the distribution of macroscopic fractures rather than microfractures.     

Large‐scale chemical stratification of fluids in the crust: hydraulic and chemical data from the geothermal research site Urach,Germany

The Urach 3 research borehole in SW Germany has been drilled through a sedimentary cover sequence and reached gneisses of the Variscan crystalline basement at 1604 m below surface. An additional 2840 m has been drilled through fractured basement rocks. The borehole has been used for hydraulic tests in the context of a ‘hot dry rock’ (HDR) project. The sedimentary cover ranges from the Carboniferous to the Middle Jurassic (Dogger) in age and comprises mostly clastic sediments in the Paleozoic and limestone and shale in the Mesozoic. Water composition data from 10 different depths include samples from all major lithological units. The total dissolved solids (TDS) increases from the surface to about 650 m where it reaches 4.1 g l^?1 in Triassic limestone. In lower Triassic sandstones, TDS increases very sharply to 28.5 g l^?1 and the water is saturated with pure CO₂ gas. With increasing depth, TDS does not change much in the clastic sediments of the Permian and Carboniferous. The crystalline basement is marked by a very sharp increase in TDS to 55.5 g l^?1 at about 1770 m depth. TDS increases within the basement to more than 78.5 g l^?1 at about 3500 m depth. The data suggest that there is limited vertical chemical communication over long periods of time. The CO₂ gas cap in the lower Triassic sandstones requires a gastight cover. The chemical stratification of the fluids relates to the permeability structure of the crust at the Urach site and fits well with hydraulic and thermal data from the site.     

Changes in chemical composition caused by water–rock interactions across a strike‐slip fault zone: case study of the Atera Fault,Central Japan

In some cases, water–rock interactions in fault zones can affect radionuclide migration. Here, we analyzed the chemical compositions of well‐exposed fault rocks from the strike‐slip Atera Fault, Central Japan, in order to understand the variability and behavior of major and selected trace elements. The fault zone has a 1.2‐m‐wide, smectite‐rich fault core and paired damage zones that developed within welded tuff on one side of the core and within granite on the other side. The 30‐cm‐wide, kaolinite‐rich fault gouge is developed in granite cataclasite, and it shows indications of the latest fault activity, while the 1.2‐m‐wide fault core appears to be older. Hydrogen and oxygen isotope ratios in the clay‐rich fault gouges, and carbon and oxygen isotope ratios in carbonates indicate that the two major clay‐rich zones formed in bedrock near the surface, consistent with observed deformation structures. Based on chemical analyses, we identified (1) a slight depletion in SiO₂, Na₂O, K₂O, and light rare earth elements at the edges of the 1.2‐m‐wide fault core, (2) a clear depletion in SiO₂, Na₂O, K₂O, and all rare earth elements except Eu in the 30‐cm‐wide fault gouge, and (3) an increase in CaO, MnO, and heavy rare earth elements across the entire 1.2‐m‐wide fault core. Findings (1) and (2) reflect water–rock interactions in the 1.2‐m‐wide fault core and in the 30‐cm‐wide fault gouge that resulted in the formation of smectite and kaolinite. Finding (3) reflects carbonate precipitation caused by the addition of basalt fragments from a nearby site to the 1.2‐m‐wide fault core during faulting, and subsequent sorption reactions of heavy rare earth elements via processes such as complexation with the carbonates.     

Pore pressure evolution and fluid flow during visco‐elastic single‐layer buckle folding

Pore pressure and fluid flow during the deformational history of geologic structures are directly influenced by tectonic deformation events. In this contribution, 2D plane strain finite element analysis is used to study the influence of different permeability distributions on the pore pressure field and associated flow regimes during the evolution of visco‐elastic single‐layer buckle folds. The buckling‐induced fluid flow regimes indicate that flow directions and, to a lesser degree, their magnitudes vary significantly throughout the deformation and as a function of the stratigraphic permeability distribution. The modelling results suggest that the volumetric strain and the permeability distribution significantly affect the resulting flow regime at different stages of fold development. For homogeneous permeability models (k > 10^?21 m²), low strain results in a mostly pervasive fluid flow regime and is in agreement with previous studies. For larger strain conditions, fluid focusing occurs in the buckling layer towards the top of the fold hinge. For low permeabilities (<10^?21 m²), local focused flow regimes inside the buckling layer emerge throughout the deformation history. For models featuring a low‐permeability layer embedded in a high‐permeability matrix or sandwiched between high‐permeability layers, focused flow regimes inside the folded layer result throughout the deformation history, but with significant differences in the flow vectors of the surrounding layers. Fluid flow vectors induced by the fold can result in different, even reversed, directions depending on the amount of strain. In summary, fluid flow regimes during single‐layer buckling can change from pervasive to focused and fluid flow vectors can be opposite at different strain levels, that is the flow vectors change significantly through time. Thus, a complete understanding of fluid flow regimes associated with single‐layer buckle folds requires consideration of the complete deformation history of the fold.     

Geological controls on regional transmissivity anisotropy

A variety of data indicate that the Carbonate aquifer in southern Manitoba is a heterogeneous and anisotropic aquifer wherein groundwater flow follows preferred flow path networks. Specific capacity tests show that aquifer transmissivity can vary by up to four orders of magnitude within 1 km. Geostatistical analysis reveals a strong anisotropy in the transmissivity field, with better spatial continuity in NE–SW and NW–SE directions, coincident with the dominant orientations of fractures observed in bedrock exposures. However, discrepancies between the orientation of highest fracture density and best transmissivity continuity suggest that either additional geological factors control the preferred flow network or there is a biased representation of the fracture pattern because all direct fracture observations came from the northern part of the study area. In an effort to investigate whether the geographically biased fracture data set represents the fracture pattern for the whole region, Landsat images and digital elevation maps were processed to extract linear features that may indicate subsurface fracture zones in areas where bedrock is covered by glacial sediments. The results suggest a consistent fracture pattern throughout the study area, indicating that the two observed fracture groups might have gone through different processes in terms of permeability development. Alteration by mineral cementation and dissolution along fracture surfaces may have preferentially improved the fracture permeability in one orientation, while reducing it in the other. The in situ stress field is also believed to play a major role in the preferred regional flow network. This paper discusses the evidence for the preferred flow path network and possible geological factors controlling aquifer anisotropy in this region.     

Hydrothermal dolomitization,mixing corrosion and deep burial porosity formation: numerical results from 1‐D reactive transport models

Major corrosion has been found at depth in carbonate hydrocarbon reservoirs from different geologic provinces. Fluid inclusion microthermometry and stable isotopic compositions of carbonate cements, predating major corrosion, constrain the interpretation of the evolution of parental fluids during progressive burial and prior to the major corrosion event. Post‐major corrosion mineral paragenesis includes pyrite (‐marcasite), anhydrite, kaolinite (dickite) and fluorite. Although the post‐corrosion mineral paragenesis represents minor volumes of rock, it may provide valuable insights into the post‐corrosion brine chemistry. Using reactive transport numerical models, the roles of cooling and/or mixing of brines on corrosion have been evaluated as controls for dolomitization, deep burial corrosion and precipitation of the post‐corrosion mineral paragenesis. Modelling results show that cooling of deep‐seated fluids moving upward along a fracture may cause minor calcite dissolution and porosity generation. Significant dolomitization along a fracture zone and nearby host‐rock only occurs when deep‐seated fluids have high salinities (4 mol Cl kg^?1 of solution) and Darcian flow rates are relatively high (1 m³ m^?2 year^?1). Only minor volumes of quartz and fluorite precipitate in the newly formed porosity. Moreover, modelling results cannot reproduce the authigenic precipitation of kaolinite (dickite at high temperatures) by cooling. As an alternative to cooling as a cause of corrosion, mixing between two brines of different compositions and salinities is represented by two main cases. One case consists of the flow up along a fracture of deep‐seated fluids with higher salinities than the fluid in the wall rock. Dolomite does not precipitate at a fracture zone. Nevertheless, minor volumes of dolomite are formed away from the fracture. The post‐corrosion mineral paragenesis can be partly reproduced, and the results are comparable to those obtained from cooling calculations. Minor volumes of quartz and fluorite are formed, and kaolinite‐dickite does not precipitate. The major outputs of this scenario are calcite dissolution and slight net increase in porosity. A second case corresponds to the mixing of low salinity deep‐seated fluids, flowing up along fractures, with high salinity brines within the wall rock. Calculations predict major dissolution of calcite and precipitation of dolomite. The post‐corrosion mineral paragenesis can be reproduced. High volumes of quartz, fluorite and kaolinite‐dickite precipitate and may even completely occlude newly formed porosity.     

Changes in fluid pathways in a calcite vein mesh (Natih Formation,Oman Mountains): insights from stable isotopes

We present a structural, microstructural, and stable isotope study of a calcite vein mesh within the Cretaceous Natih Formation in the Oman Mountains to explore changes in fluid pathways during vein formation. Stage 1 veins form a mesh of steeply dipping crack‐seal extension veins confined to a 3.5‐m‐thick stratigraphic interval. Different strike orientations of Stage 1 veins show mutually crosscutting relationships. Stage 2 veins occur in the dilatant parts of a younger normal fault interpreted to penetrate the stratigraphy below. The δ¹⁸O composition of the host rock ranges from 21.8‰ to 23.7‰. The δ¹³C composition ranges from 1.5‰ to 2.3‰. This range is consistent with regionally developed diagenetic alteration at top of the Natih Formation. The δ¹⁸O composition of vein calcite varies from 22.5‰ to 26.2‰, whereas δ¹³C composition ranges from ?0.8‰ to 2.1‰. A first trend observed in Stage 1 veins involves a decrease of δ¹³C to compositions nearly 1.3‰ lower than the host rock, whereas δ¹⁸O remains constant. A second trend observed in Stage 2 calcite has δ¹⁸O values up to 3.3‰ higher than the host rock, whereas the δ¹³C composition is similar. Stable isotope data and microstructures indicate an episodic flow regime for both stages. During Stage 1, formation of a stratabound vein mesh involved bedding‐parallel flow, under near‐lithostatic fluid pressures. The ¹⁸O fluid composition was host rock‐buffered, whereas ¹³C composition was relatively depleted. This may reflect reaction of low ¹³C CO₂ derived by fluid interaction with organic matter in the limestones. Stage 2 vein formation is associated with fault‐controlled fluid flow accessing fluids in equilibrium with limestones about 50 m beneath. We highlight how evolution of effective stress states and the growth of faults influence the hydraulic connectivity in fracture networks and we demonstrate the value of stable isotopes in tracking changes in fluid pathways.     

Permeability evolution in sorbing media: analogies between organic‐rich shale and coal

Shale gas reservoirs like coalbed methane (CBM) reservoirs are promising targets for geological sequestration of carbon dioxide (CO₂). However, the evolution of permeability in shale reservoirs on injection of CO₂ is poorly understood unlike CBM reservoirs. In this study, we report measurements of permeability evolution in shales infiltrated separately by nonsorbing (He) and sorbing (CO₂) gases under varying gas pressures and confining stresses. Experiments are completed on Pennsylvanian shales containing both natural and artificial fractures under nonpropped and propped conditions. We use the models for permeability evolution in coal (Journal of Petroleum Science and Engineering, Under Revision) to codify the permeability evolution observed in the shale samples. It is observed that for a naturally fractured shale, the He permeability increases by approximately 15% as effective stress is reduced by increasing the gas pressure from 1 MPa to 6 MPa at constant confining stress of 10 MPa. Conversely, the CO₂ permeability reduces by a factor of two under similar conditions. A second core is split with a fine saw to create a smooth artificial fracture and the permeabilities are measured for both nonpropped and propped fractures. The He permeability of a propped artificial fracture is approximately 2‐ to 3fold that of the nonpropped fracture. The He permeability increases with gas pressure under constant confining stress for both nonpropped and propped cases. However, the CO₂ permeability of the propped fracture decreases by between one‐half to one‐third as the gas pressure increases from 1 to 4 MPa at constant confining stress. Interestingly, the CO₂ permeability of nonpropped fracture increases with gas pressure at constant confining stress. The permeability evolution of nonpropped and propped artificial fractures in shale is found to be similar to those observed in coals but the extent of permeability reduction by swelling is much lower in shale due to its lower organic content. Optical profilometry is used to quantify the surface roughness. The changes in surface roughness indicate significant influence of proppant indentation on fracture surface in the shale sample. The trends of permeability evolution on injection of CO₂ in coals and shales are found analogous; therefore, the permeability evolution models previously developed for coals are adopted to explain the permeability evolution in shales.     

Constraining groundwater flow in the glacial drift and saginaw aquifers in the Michigan Basin through helium concentrations and isotopic ratios

³He and ⁴He concentrations in excess of those in water in solubility equilibrium with the atmosphere by up to two and three orders of magnitude are observed in the shallow Glacial Drift and Saginaw aquifers in the Michigan Basin. A simplified He transport model shows that in situ production is negligible and that most He excesses have a source external to the aquifer. Simulated results show that ³He and ⁴He fluxes entering the bottom of the Saginaw aquifer are 7.5 × 10^?14 and 6.1 × 10^?7 cm³STPcm^?2 yr^?1, both of which are lower than fluxes entering the underlying Marshall aquifer, 1.0 × 10^?13 and 1.6 × 10^?6 cm³STPcm^?2 yr^?1 for ³He and ⁴He, respectively. In contrast, He fluxes entering the Saginaw aquifer are higher than fluxes entering the overlying Glacial Drift aquifer of 5.2 × 10^?14 and 1.5 × 10^?7 cm³STPcm^?2 yr^?1 for ³He and ⁴He, respectively. The unusually high He fluxes and their decreasing values from the lower Marshall to the upper Glacial Drift aquifer strongly suggest the presence of an upward cross‐formational flow, with increasing He dilution toward the surface by recharge water. These fluxes are either comparable to or far greater than He fluxes in deeper aquifers around the world. Model simulations also suggest an exponential decrease in the horizontal groundwater velocity with recharge distance. Horizontal velocities vary from 13 to 2 myr^?1 for the Saginaw aquifer and from 18 to 6 myr^?1 for the Marshall aquifer. The highly permeable Glacial Drift aquifer displays a greater velocity range, from 250 to 5 myr^?1. While Saginaw ⁴He ages estimated based on the simulated velocity field display an overall agreement with ¹⁴C ages, ¹⁴C and ⁴He ages in the Glacial Drift and Marshall aquifers deviate significantly, possibly due to simplifications introduced in the He transport model leading to calculation of first‐order approximation He ages and high uncertainties in Glacial Drift ¹⁴C ages.