Gas breakthrough experiments on fine-grained sedimentary rocks

The capillary sealing efficiency of fine‐grained sedimentary rocks has been investigated by gas breakthrough experiments on fully water saturated claystones and siltstones (Boom Clay from Belgium, Opalinus Clay from Switzerland and Tertiary mudstone from offshore Norway) of different lithological compositions. Sand contents of the samples were consistently below 12%, major clay minerals were illite and smectite. Porosities determined by mercury injection lay between 10 and 30% while specific surface areas determined by nitrogen adsorption (BET method) ranged from 20 to 48 m² g ^{? 1}. Total organic carbon contents were below 2%. Prior to the gas breakthrough experiments the absolute (single phase) permeability (k_abs) of the samples was determined by steady state flow tests with water or NaCl brine. The k_abs values ranged between 3 and 550 nDarcy (3 × 10^?21 and 5.5 × 10^?19 m²). The maximum effective permeability to the gas‐phase (k_eff) measured after gas breakthrough on initially water‐saturated samples extended from 0.01 nDarcy (1 × 10^?23 m²) up to 1100 nDarcy (1.1 × 10^?18 m²). The residual differential pressures after re‐imbibition of the water phase, referred to as the ‘minimum capillary displacement pressures’ (P_d), ranged from 0.06 to 6.7 MPa. During the re‐imbibition process the effective permeability to the gas phase decreases with decreasing differential pressure. The recorded permeability/pressure data were used to derive the pore size distribution (mostly between 8 and 60 nm) and the transport porosity of the conducting pore system (10^‐5–10^‐2%). Correlations could be established between (i) absolute permeability coefficients and the maximum effective permeability coefficients and (ii) effective or absolute permeability coefficients and capillary sealing efficiency. No correlation was found between the capillary displacement pressures determined from gas breakthrough experiments and those derived theoretically by mercury injection.     

Gas breakthrough pressure for hydrocarbon reservoir seal rocks: implications for the security of long-term CO2 storage in the Weyburn field

This paper reports a laboratory study of the gas breakthrough pressure for different gas/liquid systems in the Mississippian‐age Midale Evaporite. This low‐permeability rock formation is the seal rock for the Weyburn Field in southeastern Saskatchewan, Canada, where CO₂ is being injected into an oil reservoir for enhanced recovery and CO₂ storage. A technique for experimentally determining CO₂ breakthrough pressure at reservoir conditions is presented. Breakthrough pressures for N₂, CO₂ and CH₄ were measured with the selected seal‐rock samples. The maximum breakthrough pressure is over 30 MPa for N₂ and approximately 21 MPa for CO₂. The experimental results demonstrate that the Weyburn Midale Evaporite seal rock is of high sealing quality. Therefore, the Weyburn reservoir and Midale Beds can be used as a CO₂ storage site after abandonment. The measured results also show that the breakthrough pressure of a seal rock for a gas is nearly proportional to the interfacial tension of the gas/brine system. The breakthrough pressure of a CO₂/brine system is significantly reduced compared with that of a CH₄/brine system because of the much lower interfacial tension of the former. This implies that a seal rock that seals the original gas in a gas reservoir or an oil reservoir with a gas cap may not be tight enough to seal the injected CO₂ if the pressure during or after CO₂ injection is the same or higher than the original reservoir pressure. Therefore, reevaluation of the breakthrough pressure of seal rocks for a given reservoir is necessary and of highest priority once it is chosen as a CO₂ storage site.     

Simulation of the impact of faults on CO2 injection into sandstone reservoirs

Numerical simulations of multiphase CO₂ behavior within faulted sandstone reservoirs examine the impact of fractures and faults on CO₂ migration in potential subsurface injection systems. In southeastern Utah, some natural CO₂ reservoirs are breached and CO₂‐charged water flows to the surface along permeable damage zones adjacent to faults; in other sites, faulted sandstones form barriers to flow and large CO₂‐filled reservoirs result. These end‐members serve as the guides for our modeling, both at sites where nature offers ‘successful’ storage and at sites where leakage has occurred. We consider two end‐member fault types: low‐permeability faults dominated by deformation‐band networks and high‐permeability faults dominated by fracture networks in damage zones adjacent to clay‐rich gouge. Equivalent permeability (k) values for the fault zones can range from <10^?14 m² for deformation‐band‐dominated faults to >10^?12 m² for fracture‐dominated faults regardless of the permeability of unfaulted sandstone. Water–CO₂ fluid‐flow simulations model the injection of CO₂ into high‐k sandstone (5 × 10^?13 m²) with low‐k (5 × 10^?17 m²) or high‐k (5 × 10^?12 m²) fault zones that correspond to deformation‐band‐ or fracture‐dominated faults, respectively. After 500 days, CO₂ rises to produce an inverted cone of free and dissolved CO₂ that spreads laterally away from the injection well. Free CO₂ fills no more than 41% of the pore space behind the advancing CO₂ front, where dissolved CO₂ is at or near geochemical saturation. The low‐k fault zone exerts the greatest impact on the shape of the advancing CO₂ front and restricts the bulk of the dissolved and free CO₂ to the region upstream of the fault barrier. In the high‐k aquifer, the high‐k fault zone exerts a small influence on the shape of the advancing CO₂ front. We also model stacked reservoir seal pairs, and the fracture‐dominated fault acts as a vertical bypass, allowing upward movement of CO₂ into overlying strata. High‐permeability fault zones are important pathways for CO₂ to bypass unfaulted sandstone, which leads to reduce sequestration efficiency. Aquifer compartmentalization by low‐permeability fault barriers leads to improved storativity because the barriers restrict lateral CO₂ migration and maximize the volume and pressure of CO₂ that might be emplaced in each fault‐bound compartment. As much as a 3.5‐MPa pressure increase may develop in the injected reservoir in this model domain, which under certain conditions may lead to pressures close to the fracture pressure of the top seal.     

The effect of deformation on permeability development in anhydrite and implications for caprock integrity during geological storage of CO2

Geological storage of CO₂ in depleted oil and gas reservoirs is one of the most promising options to reduce atmospheric CO₂ concentrations. Of great importance to CO₂ mitigation strategies is maintaining caprock integrity. Worldwide many current injection sites and potential storage sites are overlain by anhydrite‐bearing seal formations. However, little is known about the magnitude of the permeability change accompanying dilatation and failure of anhydrite under reservoir conditions. To this extent, we have performed triaxial compression experiments together with argon gas permeability measurements on Zechstein anhydrite, which caps many potential CO₂ storage sites in the Netherlands. Our experiments were performed at room temperature at confining pressures of 3.5–25 MPa. We observed a transition from brittle to semi‐brittle behaviour over the experimental range, and peak strength could be described by a Mogi‐type failure envelope. Dynamic permeability measurements showed a change from ‘impermeable’ (<10^?21 m²) to permeable (10^?16 to 10^?19 m²) as a result of mechanical damage. The onset of measurable permeability was associated with an increase in the rate of dilatation at low pressures (3.5–5 MPa), and with the turning point from compaction to dilatation in the volumetric versus axial strain curve at higher pressures (10–25 MPa). Sample permeability was largely controlled by the permeability of the shear faults developed. Static, postfailure permeability decreased with increasing effective mean stress. Our results demonstrated that caprock integrity will not be compromised by mechanical damage and permeability development. Geofluids (2010) 10 , 369–387     

Effective gas permeability of Tight Gas Sandstones as a function of capillary pressure – a non‐steady‐state approach

Single‐ and two‐phase (gas/water) fluid transport in tight sandstones has been studied in a series of permeability tests on core plugs of nine tight sandstones of the southern North Sea. Absolute (Klinkenberg‐corrected) gas permeability coefficients (k_gas__inf) ranged between 3.8 × 10^?16 and 6.2 × 10^?19 m² and decreased with increasing confining pressure (10–30 MPa) by a factor 3–5. Klinkenberg‐corrected (intrinsic) gas permeability coefficients were consistently higher by factors from 1.4 to 10 than permeability coefficients determined with water. Non‐steady‐state two‐phase (He/water) flow experiments conducted up to differential pressures of 10 MPa document the dynamically changing conductivity for the gas phase, which is primarily capillary‐controlled (drainage and imbibition). Effective gas permeability coefficients in the two‐phase flow tests ranged between 1.1 × 10^?17 and 2.5 × 10^?22 m², corresponding to relative gas permeabilities of 0.03% and 10%. In the early phase of the nonstationary flow regime (before establishment of steady‐state conditions), they may be substantially (>50%) lower. Effective gas permeability measurements are affected by the following factors: (i) Capillary‐controlled drainage/imbibition, (ii) viscous–dynamic effects (iii) and slip flow.     

Molecular transport of methane, ethane and nitrogen and the influence of diffusion on the chemical and isotopic composition of natural gas accumulations

Laboratory experiments have been performed to determine diffusion coefficients of natural gas components (methane, ethane and nitrogen) and isotope fractionation effects under simulated in situ pressure (up to 45 MPa effective stress) and temperature conditions (50–200°C) in water‐saturated pelitic and coarse‐grained rocks. Effective diffusion coefficients of molecular nitrogen (0.39 × 10^?11 to 21.6 × 10^?11 m² sec^?1 at 90°C) are higher than those for methane (0.18 × 10^?11 to 18.2 × 10^?11 m² sec^?1 at 90°C). Diffusive flux rates expressed in mass units are generally higher for N₂ than for CH₄. Both methane and (to a lesser extent) nitrogen diffusion coefficients decrease with increasing total organic carbon (TOC) content of the rock samples because of sorption processes on the organic matter. This effect decreases with increasing temperature. Effective diffusion coefficients increase upon a temperature increase from 50 to 200°C by a factor of four. Effective diffusion coefficients and steady‐state diffusive flux decrease with effective stress. Stationary diffusive fluxes drop by 50–70% for methane and 45–62% for nitrogen while effective diffusion coefficients are reduced by 38% (CH₄) and 32–48% (N₂), respectively. Isotope fractionation coefficients of diffusive transport are higher for methane (?1.56 and ?2.77‰) than for ethane (?0.84 and ?1.62‰). Application of the experimental results to geological systems show that diffusive transport has only a low transport efficiency. Significant depletion of natural gas reservoirs by molecular diffusion is only expected in cases of very poor caprock qualities (in terms of thickness and/or porosity) and over extended periods of geological time. Under these circumstances, the chemical and isotopic composition of a gas reservoir will change and maturity estimates based on these parameters may be deceptive. To account for these potential effects, nomograms have been developed to estimate diffusive losses and apply maturity corrections.     

Hydrogeochemical modelling of CO2 equilibria and mass transfer induced by organic–inorganic interactions in siliciclastic petroleum reservoirs

Different feldspar types control complex hydrogeochemical processes in hydrocarbon‐bearing siliciclastic reservoirs, which have undergone different degrees of degradation. To test such processes generically, carbon dioxide equilibria and mass transfers induced by organic–inorganic interactions have been modelled for different hydrogeochemical scenarios. The approach is based on and compared with data from the Norwegian continental shelf ( Smith & Ehrenberg 1989 ) and assumes local thermodynamic equilibrium among solids and fluids. Equilibrating mineral assemblages (different feldspar types, quartz, kaolinite, calcite) are based on the primary reservoir composition. Equilibration and coupled mass transfer were triggered by the addition and reaction of different amounts of CO₂, CH₄ and H₂ (plus acetic acid) at temperatures between 50 and 95°C (323 and 368 K). These components occur in oil fields as products of anaerobic bacterial degradation, hydrolytic disproportionation of hydrocarbons and/or thermal maturation of kerogen. We apply two different computer codes and two different thermodynamic data bases to calculate the results. Reaction of 0.32–0.6 mol CO₂, 0.16–0.3 mol CH₄ and 0.8–1.5 mol H₂ with K‐feldspar, quartz, kaolinite and calcite in 1 l of pore water results in modelled values of 0.3–2.3 mol% CO₂ in a multicomponent gas phase that resembles measured data (0.2–1.5 mol%). Similar CO₂ contents result from acetic acid addition (CO₂, CH₄, H₂ + 0.016 mol CH₃COOH). Equilibration with albite or anorthite reduces the release of CO₂ into the multicomponent gas phase dramatically, by 1 or 4 orders of magnitude compared with the equilibration with K‐feldspar. Minor differences in the modelled CO₂ content (0.1–0.2 mol%) result from calculations with different computer codes if the same thermodynamic data base is applied. Relevant differences (up to 1.9 mol% CO₂) result from calculations using different thermodynamic data bases.     

Constraining the rate and extent of mantle serpentinization from seismic and petrological data: implications for chemosynthesis and tectonic processes

We used seismic velocity as a proxy for serpentinization of the mantle, which occurred beneath thinned but laterally continuous continental crust during continental break up, prior to opening of the Atlantic Ocean. The serpentinized sub‐continental mantle is now exhumed, beneath the Iberia Abyssal Plain and was accessed by scientific drilling on Ocean Drilling Program legs 149 and 173. Chromatographic modelling of kinetically limited transport of the serpentinization front yields a front displacement of 2197 ± 89 m, a time‐integrated fluid flux of 1098 ± 45 m³ m^?2 and a Damköhler number of 6.0 ± 0.2. Whether either surface reaction or chemical transport limit the rate of reaction, we calculate timescales for serpentinization of approximately 10⁵–10⁶ years. This yields time‐average fluid flux rates for H₂O, entering and reacting with the mantle, of 60–600 mol m^?2 a^?1 and for CH₄, produced as a by‐product of oxidation of Fe⁺⁺ to magnetite and exiting the mantle, of 0.55–5.5 mol m^?2 a^?1. This equates to a CH₄‐flux of 0.18–1.8 Tg a^?1 for coeval serpentinization of the mantle that was exhumed west of Iberia. This represents 0.03–0.3% of the present‐day annual CH₄‐flux from all sources and a higher fraction of pre‐anthropogenic (lower) CH₄ levels. CH₄ released by serpentinization at or beneath the seafloor could provide substrate for biological chemosynthesis and/or promote gas‐hydrate formation. Finally, noting its volumetric extent and rapidity (<10⁶ years), we interpret serpentinization to be a reckonable component of tectonic processes, contributing both diapiric and expansional forces and helping to ‘lubricate’ extensional processes. Given its anisotropic permeability, actively deforming serpentinite might impede melt migration which may be of interest, given the apparent lack of melt in some rifted margins.     

On the geochemistry of gases and noble gas isotopes (including 222Rn) in deep crustal fluids: the 4000 m KTB-pilot hole fluid production test 2002–03

The concentrations of H₂, O₂, CO₂, and concentrations and isotopic composition of the noble gases (including ²²²Rn), N₂, CH₄, and higher hydrocarbons dissolved in 4000 m deep‐seated fluids from a 12‐month fluid production test in the KTB pilot hole were analyzed. This determination of the gas geochemistry during the test in combination with the knowledge of the hydraulic data provides relevant information about the fluid hydraulics of the deep system. All gas concentrations and isotopic signatures, except for ²²²Rn, showed constancy during the course of the test. This, in combination with large fluid flow rates at a moderate water table drawdown, imply an almost infinite fluid reservoir in 4000 m depth. From the change in ²²²Rn‐activity as a function of pump rate, the contribution of smaller and wider pores to the overall fluid flow in an aquifer can be deduced. This ²²²Rn‐activity monitoring proved therefore to be a valuable instrument for the qualitative observation of the scavenging of pore and fracture surfaces, a hydraulic feature invisible to standard hydraulic testing tools. The observance of this scavenging effect is due to (i) the continuous on‐line geochemical monitoring, (ii) the durability of the test, (iii) a change in pump rate during the course of the test, and (iv) due to the short half‐life of ²²²Rn. The fluids have a 5.9% mantle He component, and a δ²¹Ne excess of 14%, and a noble gas model age of about (5.5–6.2) ± 2.0 Myr. The mean N₂/Ar‐ratio of 516 and δ¹⁵N‐data of about +1.5‰ indicates sedimentary or metamorphic origin of N₂. The hydrocarbons, amounting to 33 vol.% in the gas phase, are derived from thermal decomposition of marine organic matter of low maturity. But a key question, the identification of the potential source region of the fluids and the migration pathway, is still unidentified.     

Study of coal gas wettability for CO2 storage and CH4 recovery

To quantify and rank gas wettability of coal as a key parameter affecting the extent of CO₂ sequestration in coal and CH₄ recovery from coal, we developed a contact angle measuring system based on a captive gas bubble technique. We used this system to study the gas wetting properties of an Australian coal from the Sydney Basin. Gas bubbles were generated and captivated beneath a coal sample within a distilled water‐filled (pH 5.7) pressurised cell. Because of the use of distilled water, and the continuous dissolution and shrinkage of the gas bubble in water during measurement, the contact angles measured correspond to a ‘transient receding’ contact angle. To take into account the mixed‐gas nature (CO₂, CH₄, and to a lesser extent N₂) of coal seam gas in the basin, we evaluated the relative wettability of coal by CH₄, CO₂ and N₂ gases in the presence of water. Measurements were taken at various pressures of up to 15 MPa for CH₄ and N₂, and up to 6 MPa for CO₂ at a constant temperature of 22°C. Overall, our results show that CO₂ wets coal more extensively than CH₄, which in turn wets coal slightly more than N₂. Moreover, the contact angle reduces as the pressure increases, and becomes < 90° at various pressures depending on the gas type. In other words, all three gases wet coal better than water under sufficiently high pressure.     

Permeability evolution in sorbing media: analogies between organic‐rich shale and coal

Shale gas reservoirs like coalbed methane (CBM) reservoirs are promising targets for geological sequestration of carbon dioxide (CO₂). However, the evolution of permeability in shale reservoirs on injection of CO₂ is poorly understood unlike CBM reservoirs. In this study, we report measurements of permeability evolution in shales infiltrated separately by nonsorbing (He) and sorbing (CO₂) gases under varying gas pressures and confining stresses. Experiments are completed on Pennsylvanian shales containing both natural and artificial fractures under nonpropped and propped conditions. We use the models for permeability evolution in coal (Journal of Petroleum Science and Engineering, Under Revision) to codify the permeability evolution observed in the shale samples. It is observed that for a naturally fractured shale, the He permeability increases by approximately 15% as effective stress is reduced by increasing the gas pressure from 1 MPa to 6 MPa at constant confining stress of 10 MPa. Conversely, the CO₂ permeability reduces by a factor of two under similar conditions. A second core is split with a fine saw to create a smooth artificial fracture and the permeabilities are measured for both nonpropped and propped fractures. The He permeability of a propped artificial fracture is approximately 2‐ to 3fold that of the nonpropped fracture. The He permeability increases with gas pressure under constant confining stress for both nonpropped and propped cases. However, the CO₂ permeability of the propped fracture decreases by between one‐half to one‐third as the gas pressure increases from 1 to 4 MPa at constant confining stress. Interestingly, the CO₂ permeability of nonpropped fracture increases with gas pressure at constant confining stress. The permeability evolution of nonpropped and propped artificial fractures in shale is found to be similar to those observed in coals but the extent of permeability reduction by swelling is much lower in shale due to its lower organic content. Optical profilometry is used to quantify the surface roughness. The changes in surface roughness indicate significant influence of proppant indentation on fracture surface in the shale sample. The trends of permeability evolution on injection of CO₂ in coals and shales are found analogous; therefore, the permeability evolution models previously developed for coals are adopted to explain the permeability evolution in shales.     

Permeability of the Mercia Mudstone: suitability as caprock to carbon capture and storage sites

The Upper Triassic Mercia Mudstone is the caprock to potential carbon capture and storage (CCS) sites in porous and permeable Lower Triassic Sherwood Sandstone reservoirs and aquifers in the UK (primarily offshore). This study presents direct measurements of vertical (k_v) and horizontal (k_h) permeability of core samples from the Mercia Mudstone across a range of effective stress conditions to test their caprock quality and to assess how they will respond to changing effective stress conditions that may occur during CO₂ injection and storage. The Mercia samples analysed were either clay‐rich (muddy) siltstones or relatively clean siltstones cemented by carbonate and gypsum. Porosity is fairly uniform (between 7.4 and 10.7%). Porosity is low either due to abundant depositional illite or abundant diagenetic carbonate and gypsum cements. Permeability values are as low as 10^?20 m² (10nD), and therefore, the Mercia has high sealing capacity. These rocks have similar horizontal and vertical permeabilities with the highest k_h/k_v ratio of 2.03 but an upscaled k_h/k_v ratio is 39, using the arithmetic mean of k_h and the harmonic mean of k_v. Permeability is inversely related to the illite clay content; the most clay‐rich (illite‐rich) samples represent very good caprock quality; the cleaner Mercia Mudstone samples, with pore‐filling carbonate and gypsum cements, represent fair to good caprock quality. Pressure sensitivity of permeability increases with increasing clay mineral content. As pore pressure increases during CO₂ injection, the permeability of the most clay‐rich rocks will increase more than carbonate‐ and gypsum‐rich rocks, thus decreasing permeability heterogeneity. The best quality Mercia Mudstone caprock is probably not geochemically sensitive to CO₂ injection as illite, the cause of the lowest permeability, is relatively stable in the presence of CO₂–water mixtures.     

Decreasing CO2 partial pressure triggered Mg–Fe–Ca carbonate formation in ancient Martian crust preserved in the ALH84001 Meteorite

We retrace hydrogeochemical processes leading to the formation of Mg–Fe–Ca carbonate concretions (first distinct carbonate population, FDCP) in Martian meteorite ALH84001 by generic hydrogeochemical equilibrium and mass transfer modeling. Our simple conceptual models assume isochemical equilibration of orthopyroxenite minerals with pure water at varying water‐to‐rock ratios, temperatures and CO₂ partial pressures. Modeled scenarios include CO₂ partial pressures ranging from 10.1325 to 0.0001 MPa at water‐to‐rock ratios between 4380 and 43.8 mol mol^?1 and different temperatures (278, 303 and 348 K) and enable the precipitation of Mg–Fe–Ca solid solution carbonate. Modeled range and trend of carbonate compositional variation from magnesio‐siderite (core) to magnesite (rim), and the precipitation of amorphous SiO₂ and magnetite coupled to magnesite‐rich carbonate are similar to measured compositional variation. The results of this study suggest that the early Martian subsurface had been exposed to a dynamic gas pressure regime with decreasing CO₂ partial pressure at low temperatures (approximately 1.0133 to 0.0001 MPa at 278 K or 6 to 0.0001 MPa at 303 K). Moderate water‐to‐rock ratios of ca. 438 mol mol^?1 and isochemical weathering of orthopyroxenite are additional key prerequisites for the formation of secondary phase assemblages similar to ALH84001’s ‘FDCP’. Outbursts of water and CO_2(g) from confined ground water in fractured orthopyroxenite rocks below an unstable CO₂ hydrate‐containing cryosphere provide adequate environments on the early Martian surface.     

3D numerical modeling of hydrothermal processes during the lifetime of a deep geothermal reservoir

Understanding hydrothermal processes during production is critical to optimal geothermal reservoir management and sustainable utilization. This study addresses the hydrothermal (HT) processes in a geothermal research doublet consisting of the injection well E GrSk3/90 and production well Gt GrSk4/05 at the deep geothermal reservoir of Groß Schönebeck (north of Berlin, Germany) during geothermal power production. The reservoir is located between ?4050 to ?4250 m depth in the Lower Permian of the Northeast German Basin. Operational activities such as hydraulic stimulation, production (T = 150°C; Q = ?75 m³ h^?1; C = 265 g l^?1) and injection (T = 70°C; Q = 75 m³ h^?1; C = 265 g l^?1) change the HT conditions of the geothermal reservoir. The most significant changes affect temperature, mass concentration and pore pressure. These changes influence fluid density and viscosity as well as rock properties such as porosity, permeability, thermal conductivity and heat capacity. In addition, the geometry and hydraulic properties of hydraulically induced fractures vary during the lifetime of the reservoir. A three‐dimensional reservoir model was developed based on a structural geological model to simulate and understand the complex interaction of such processes. This model includes a full HT coupling of various petrophysical parameters. Specifically, temperature‐dependent thermal conductivity and heat capacity as well as the pressure‐, temperature‐ and mass concentration‐dependent fluid density and viscosity are considered. These parameters were determined by laboratory and field experiments. The effective pressure dependence of matrix permeability is less than 2.3% at our reservoir conditions and therefore can be neglected. The results of a three‐dimensional thermohaline finite‐element simulation of the life cycle performance of this geothermal well doublet indicate the beginning of thermal breakthrough after 3.6 years of utilization. This result is crucial for optimizing reservoir management. Geofluids (2010) 10 , 406–421     

Geochemistry and origin of natural gases dissolved in brines from gas fields in southwest Japan

Previous geochemical studies indicated that most natural gases dissolved in brines in Japan are of microbial origin, consisting of methane produced via carbonate reduction. However, some of those from gas fields in southwest Japan contain methane relatively enriched in ¹³C, whose origin remains to be clarified. To address this issue, chemical and isotopic analyses were performed on natural gases and brines from the gas fields in Miyazaki and Shizuoka prefectures, southwest Japan. Methane isotopic signatures (δ¹³C ≈ ?68‰ to ?34‰ VPDB; δ²H ≈ ?183‰ to ?149‰ VSMOW) suggest that these gases are of microbial (formed via carbonate reduction) or of mixed microbial and thermogenic origin. The relatively high δ²H‐CH₄ values and their relationship with the δ²H‐H₂O values argue against the possibility of their formation via acetate fermentation. The δ¹³C‐CO₂ values (≈?5‰), together with the slope of the correlation between δ²H‐CH₄ and δ¹³C‐CH₄ (Δδ²H‐CH₄/Δδ¹³C‐CH₄ ≈ 1), contradict the possibility of their formation via carbonate reduction followed by partial oxidation by methanotrophs. The ³He/⁴He ratios of the gases from Miyazaki (≈0.11–1.3 Ra) and their low correlation with δ¹³C‐CH₄ values do not support an abiogenic origin. It is inferred therefore that the high δ¹³C‐CH₄ values of natural gases dissolved in brines from gas fields in southwest Japan are indications of the contribution of thermogenic hydrocarbons, although whether abiogenic hydrocarbons contribute significantly to the gases from Shizuoka requires further investigation. This study has clarified that, for the future exploration of natural gases in southwest Japan, we should adopt the strategies for conventional thermogenic gas accumulations, such as checking the content, type and maturity of organic matter in the underlying sedimentary rocks.     

Wettability alteration of caprock minerals by carbon dioxide

One of the critical factors that control the efficiency of CO₂ geological storage process in aquifers and hydrocarbon reservoirs is the capillary‐sealing potential of the caprock. This potential can be expressed in terms of the maximum reservoir overpressure that the brine‐saturated caprock can sustain, i.e. of the CO₂ capillary entry pressure. It is controlled by the brine/CO₂ interfacial tension, the water‐wettability of caprock minerals, and the pore size distribution within the caprock. By means of contact angle measurements, experimental evidence was obtained showing that the water‐wettability of mica and quartz is altered in the presence of CO₂ under pressures typical of geological storage conditions. The alteration is more pronounced in the case of mica. Both minerals are representative of shaly caprocks and are strongly water‐wet in the presence of hydrocarbons. A careful analysis of the available literature data on breakthrough pressure measurements in caprock samples confirms the existence of a wettability alteration by dense CO₂, both in shaly and in evaporitic caprocks. The consequences of this effect on the maximum CO₂ storage pressure and on CO₂ storage capacity in the underground reservoir are discussed. For hydrocarbon reservoirs that were initially close to capillary leakage, the maximum allowable CO₂ storage pressure is only a fraction of the initial reservoir pressure.     

The upper continental crust, an aquifer and its fluid: hydaulic and chemical data from 4 km depth in fractured crystalline basement rocks at the KTB test site

Detailed information on the hydrogeologic and hydraulic properties of the deeper parts of the upper continental crust is scarce. The pilot hole of the deep research drillhole (KTB) in crystalline basement of central Germany provided access to the crust for an exceptional pumping experiment of 1‐year duration. The hydraulic properties of fractured crystalline rocks at 4 km depth were derived from the well test and a total of 23100 m³ of saline fluid was pumped from the crustal reservoir. The experiment shows that the water‐saturated fracture pore space of the brittle upper crust is highly connected, hence, the continental upper crust is an aquifer. The pressure–time data from the well tests showed three distinct flow periods: the first period relates to wellbore storage and skin effects, the second flow period shows the typical characteristics of the homogeneous isotropic basement rock aquifer and the third flow period relates to the influence of a distant hydraulic border, probably an effect of the Franconian lineament, a steep dipping major thrust fault known from surface geology. The data analysis provided a transmissivity of the pumped aquifer T = 6.1 × 10^?6 m² sec^?1, the corresponding hydraulic conductivity (permeability) is K = 4.07 × 10^?8 m sec^?1 and the computed storage coefficient (storativity) of the aquifer of about S = 5 × 10^?6. This unexpected high permeability of the continental upper crust is well within the conditions of possible advective flow. The average flow porosity of the fractured basement aquifer is 0.6–0.7% and this range can be taken as a representative and characteristic values for the continental upper crust in general. The chemical composition of the pumped fluid was nearly constant during the 1‐year test. The total of dissolved solids amounts to 62 g l^?1 and comprise mainly a mixture of CaCl₂ and NaCl; all other dissolved components amount to about 2 g l^?1. The cation proportions of the fluid (X_Ca approximately 0.6) reflects the mineralogical composition of the reservoir rock and the high salinity results from desiccation (H₂O‐loss) due to the formation of abundant hydrate minerals during water–rock interaction. The constant fluid composition suggests that the fluid has been pumped from a rather homogeneous reservoir lithology dominated by metagabbros and amphibolites containing abundant Ca‐rich plagioclase.     

Effects of episodic fluid flow on hydrocarbon migration in the Newport‐Inglewood Fault Zone,Southern California

Fault permeability may vary through time due to tectonic deformations, transients in pore pressure and effective stress, and mineralization associated with water‐rock reactions. Time‐varying permeability will affect subsurface fluid migration rates and patterns of petroleum accumulation in densely faulted sedimentary basins such as those associated with the borderland basins of Southern California. This study explores the petroleum fluid dynamics of this migration. As a multiphase flow and petroleum migration case study on the role of faults, computational models for both episodic and continuous hydrocarbon migration are constructed to investigate large‐scale fluid flow and petroleum accumulation along a northern section of the Newport‐Inglewood fault zone in the Los Angeles basin, Southern California. The numerical code solves the governing equations for oil, water, and heat transport in heterogeneous and anisotropic geologic cross sections but neglects flow in the third dimension for practical applications. Our numerical results suggest that fault permeability and fluid pressure fluctuations are crucial factors for distributing hydrocarbon accumulations associated with fault zones, and they also play important roles in controlling the geologic timing for reservoir filling. Episodic flow appears to enhance hydrocarbon accumulation more strongly by enabling stepwise build‐up in oil saturation in adjacent sedimentary formations due to temporally high pore pressure and high permeability caused by periodic fault rupture. Under assumptions that fault permeability fluctuate within the range of 1–1000 millidarcys (10^?15–10^?12 m²) and fault pressures fluctuate within 10–80% of overpressure ratio, the estimated oil volume in the Inglewood oil field (approximately 450 million barrels oil equivalent) can be accumulated in about 24 000 years, assuming a seismically induced fluid flow event occurs every 2000 years. This episodic petroleum migration model could be more geologically important than a continuous‐flow model, when considering the observed patterns of hydrocarbons and seismically active tectonic setting of the Los Angeles basin.     

Reanalysis of in situ permeability measurements in the Barbados décollement

A cased and sealed borehole in the Northern Barbados accretionary complex was the site of the first attempts to measure permeability in situ along a plate boundary décollement. Three separate efforts at Hole 949C yielded permeability estimates for the décollement spanning four orders of magnitude. An analysis of problems encountered during installation of the casing and seals provides insights into how the borehole conditions may have led to the wide range of results. During the installation, sediments from the surrounding formation repeatedly intruded into the borehole and casing. Stress analysis shows that the weak sediments were deforming plastically and the radial and tangential stresses around the borehole were significantly lower than lithostatic. This perturbed stress state may explain why the test pressure records showed indications of hydrofracture at pressures below lithostatic, and permeabilities rose rapidly as the estimated effective stress dropped below 0.8 MPa. Even after the borehole was sealed, the plastic deformation of the formation and relatively large gap of the wire wrapped screen allowed sediment to flow into the casing. Force equilibrium calculations predict sediment would have filled the borehole to 10 cm above the top of the screen by the time slug tests were conducted 1.5 years after the borehole was sealed. Reanalysis of the slug test results with these conditions yields several orders of magnitude higher permeability estimates than the original analysis which assumed an open casing. Overall the results based on only the tests with no sign of hydrofracture yield a permeability range of 10^?14–10^?15 m² and a rate of increase in permeability with decreasing effective stress consistent with laboratory tests on samples from the décollement zone.     

Are rocks still water‐wet in the presence of dense CO2 or H2S?

The various modes of acid gas storage in aquifers, namely structural, residual, and local capillary trapping, are effective only if the rock remains water‐wet. This paper reports an evaluation, by means of the captive‐bubble method, of the water‐wet character in presence of dense acid gases (CO₂, H₂S) of typical rock‐forming minerals such as mica, quartz, calcite, and of a carbonate‐rich rock sampled from the caprock of a CO₂ storage reservoir in the South‐West of France. The method, which is improved from that previously implemented with similar systems by Chiquet et al. (Geofluids 2007; 7 : 112), allows the advancing and receding contact angles, as well as the adhesion behavior of the acid gas on the mineral substrate, to be evaluated over a large range of temperatures (up to 140°C), pressures (up to 150 bar), and brine salinities (up to NaCl saturation) representative of various geological storage conditions. The water‐receding (or gas‐advancing) angle that controls structural and local capillary trapping is observed to be not significantly altered in the presence of dense CO₂ or H₂S. In contrast, some alteration of the water‐advancing (or gas‐receding) angle involved in residual trapping is observed, along with acid gas adhesion, particularly on mica. A spectacular wettability reversal is even observed with mica and liquid H₂S. These results complement other recent observations on similar systems and present analogies with the wetting behavior of crude oil/brine/mineral systems, which has been thoroughly studied over the past decades. An insight is given into the interfacial forces that govern wettability in acid gas‐bearing aquifers, and the consequences for acid gas geological storage are discussed along with open questions for future work.