EXPERIMENTAL BEHAVIOUR OF R/C FRAMES RETROFITTED WITH DISSIPATING AND RE-CENTRING BRACES

An extensive program of shaking table tests on 1/4-scale three-dimensional R/C frames was jointly carried out by the Department of Structure, Soil Mechanics and Engineering Geology (DiSGG) of the University of Basilicata, Italy, and the National Laboratory of Civil Engineering (LNEC), Portugal. It was aimed at evaluating the effectiveness of passive control bracing systems for the seismic retrofit of R/C frames designed for gravity loads only. Two different types of braces were considered, one based on the hysteretic behaviour of steel elements, the other on the superelastic properties of Shape Memory Alloys (SMA). Different protection strategies were pursued, in order to fully exploit the high energy dissipation capacity of steel-based devices, on one hand, and the supple-mental re-centring capacity of SMA-based devices, on the other hand. The experimental results confirmed the great potentials of both strategies and of the associated devices in limiting structural damage. The retrofitted model was subjected to table accelerations as high as three times the acceleration leading the unprotected model to collapse, with no significant damage to structural elements. Moreover, the re-centring capability of the SMA-based bracing system was able to recover the undeformed shape of the frame, when it was in a near-collapse condition. In this paper the experimental behaviour of the non protected and of the protected structural models are described and compared.     

Modeling and Seismic Response Analysis of Italian Code-Conforming Single-Storey Steel Buildings

ABSTRACT

This article describes the structural design, nonlinear modeling, and seismic analysis of prototype single-storey non-residential steel buildings made of moment-resisting portal frames in the transverse direction and concentric braces in the longitudinal direction. Various design parameters (building geometry, seismic hazard, foundation soil category) and different modeling assumptions (bare frame model, model including cladding elements, ground motions including vertical accelerations, and modeling uncertainties) were considered to investigate their effects on the simulated seismic performance.     

Cyclic Performance of an Elliptical-Shaped Damper with Shear Diaphragms in Chevron Braced Steel Frames

Several advantages of yielding dampers in controlling seismic energy have attracted the attention of many researchers in designing new buildings and retrofitting existing structures. In recent decades, various shapes and substances of such dampers have been used in engineering structures and their behavioral features, including the energy dissipating capacities, have been assessed. In this article, a novel method is presented to obtain the design relationship of two types of yielding elliptical dampers in terms of their selected geometric properties, i.e. distance between the shear diaphragms or virtual diameter and thickness. In addition, two different elliptical-shaped steel dampers equipped with the shear diaphragms are proposed and modeled using the finite element software ABAQUS and their performances are investigated. Then, 30 and 25 models, respectively, of the first and second types are studied using pushover analysis. The designed dampers considering the proposed relationships are used in two chevron braced steel frames placed between the bracing and the beam. Due to their desirable efficiency in energy dissipation and increase in the equivalent viscous damping of the frame, better efficiency is achieved in the modified damper with easier fabrication.     

Seismic Behavior of FRP-Retrofitted Reinforced Concrete Frames

Although a significant number of studies have been conducted on the behavior of the reinforced concrete beam-column joints retrofitted with FRP materials, limited investigation considered the overall seismic behavior of the retrofitted frames. In this article, experimental and numerical studies are performed on a scaled-down eight-story and two full scaled low-rise ordinary moment resisting frames (OMRFs) retrofitted with FRP at the joints. Additional, rotational stiffness of the joints is implemented into pushover models to predict seismic performance and behavior factor of the retrofitted frames. Results indicate that FRP retrofitting is more effective than steel braces for low- and medium-rise OMRFs.     

Pseudo Dynamic Testing of an RC Frame Retrofitted with Chevron Braces

Two-story three-bay reinforced concrete frames with and without chevron brace was tested using pseudo dynamic test method. The chevron braces were implemented to the interior span of the RC frame. Chevron-braced frame was observed to be effective to control inter-story drift demands. Based on the observed damage state and dynamic response of the test frames, performance states were discussed for different scales of Duzce ground motions. The test results were compared with the results of the nonlinear time history analysis. The analysis results were capable of estimating the base shear capacity and displacement demands with a reasonable accuracy.     

SEISMIC FRAGILITY OF LRC FRAMES WITH AND WITHOUT MASONRY INFILL WALLS

This paper summarises the first phase of the fragility analyses of generic (representative) buildings in the area of Memphis, Tennessee, USA. The study was conducted at Cornell University as a part of the project Loss Assessment of Memphis Buildings (LAMB) for the National Center for Earthquake Engineering Research (NCEER). In this study, the fragility analyses focus on low-rise Lightly Reinforced Concrete (LRC) frame buildings with and without infill walls. The obtained fragility curves are compared with those of ATC-13 for different facility classes. Based on the obtained fragility curves, it is concluded that adding masonry infill wails to low-rise LRC frame buildings significantly reduces the likelihood of seismic damage.     

Elastic Displacement Spectrum-Based Design Approach for Buckling-Restrained Braced Frames

The design focus for a buckling-restrained braced frame (BRBF) is that the buckling-restrained braces (BRBs) dissipate most of the seismic energy while the main frame retains a degree of elastic stiffness under a major earthquake. An elastic displacement spectrum based design method is presented in this article, which can directly determine the sectional area of the BRBs. The yield displacement in the roof of the main frame is taken as the target displacement under a major earthquake. An elastic displacement design spectrum is used to solve the target period of the BRBF. To validate this method, a six-story buckling-restrained braced steel frame is designed using the proposed method, and a series of nonlinear response history analyses (RHAs) are performed to verify the design result. The example shows that the required BRB area can be simply and accurately determined by the proposed method. The error between the given target displacement and the RHA results is 4.0% and 21.3% for BRBFs designed with BRB yield strength of 235 Mpa and 100 Mpa, respectively.     

Seismic Vulnerability of Historical Masonry Aggregate Buildings in Oriental Sicily

ABSTRACT

The seismic vulnerability assessment of historical UnReinforced Masonry (URM) buildings is a very complex task since it is strongly related to a great variety both of geometrical layouts and of masonry mechanical characteristics. In this article, some results of a Catania University research project, denomined “FIR 2014”, focused on the seismic vulnerability estimation of historical buildings, built in Catania after the 1963 earthquake, are presented. First, a detailed typological analysis of the considered urban fabric, characterized by typical residential masonry buildings, has been performed. Such analysis allowed recognizing an elementary structural modulus, which has been studied according to different geometrical layouts representative of isolated or aggregate buildings. The results of nonlinear static analyses, performed by applying an innovative macro-element approach, allowed for the assessment the seismic vulnerability of typical URM buildings coherently to the Italian seismic code. The adopted macro-element strategy for the seismic assessment of aggregate masonry buildings, although related to a specific historical center, may be applied to similar urban fabrics and can also be used for the calibration and validation of fast seismic assessment strategies, particularly useful for the evaluation of the seismic risk at urban scale.     

Testing of Superelastic Recentering Pre-Strained Braces for Seismic Resistant Design

Over the past decade, the use of shape memory alloys (SMAs) in passive control devices has been explored. Nevertheless, some aspects in regards to the cyclic behavior of SMAs and the effect of pre-straining need to be clarified. In this study, small-scale shake table tests have been performed to explore the effectiveness of SMA bracing systems as compared to steel bracing systems. The reduced-scale experimental results imply that SMAs used in braces are more effective in controlling the response of a steel frame compared with a traditional bracing system. A finite element model (FEM) of the frame is developed in order to compare the analytical results with the shake table tests. Further, the effect of pre-straining the SMA braces is evaluated through both experimental and analytical studies. The results show that pre-straining improves the performance of the frame compared to the nonpre-strained case. However, as the level of pre-straining increases above approximately 1.0% to 1.5%, the benefits of pre-straining decrease compared with low-to-moderate pre-strain levels.     

Numerical Simulation and Seismic Fragility Analysis of a Self-Centering Steel MRF with Web Friction Devices

This article presents the seismic fragility analysis of a self-centering steel moment-resisting frame (SC-MRF) with web friction devices. A detailed numerical model of the SC frame was developed using the Open System for Earthquake Engineering Simulation (OpenSees) and the elastoplastic responses of the SC-MRF were studied, including the strength degradation under cyclic loading, tendon rupture, beam buckling, bolt bearing and friction loss, etc. The proposed simulation approach is validated by comparing the simulated results with those in existing hybrid-simulation tests, quasi-static pushover test and low cyclic tests, where good agreement is observed. In addition to the well-established performance limit states (i.e., immediate occupancy, collapse prevention and global dynamic instability), two unique performance limit states (i.e., the recentering and repairable limit states) are defined for the SC-MRF. Finally, incremental dynamic analyses are conducted to evaluate the seismic fragilities regarding the five performance limit states.     

Seismic Reliability of Code-Conforming Italian Buildings

ABSTRACT

This paper presents and discusses some research results related to the seismic failure risk of standard, residential and industrial, buildings designed for damage, and life-safety according to the Italian seismic code, which is somewhat similar to Eurocode 8. The five considered structural typologies are as follows: masonry, cast-in-place reinforced concrete, precast reinforced concrete, steel, and base-isolated buildings. The archetype structures have been designed according to standard practice at three sites, representative of the seismic hazard across the country. Seismic risk is defined here as the annual rate of earthquakes able to cause structural failure in terms of usability-preventing damage and global collapse. For each structure, the failure rates have been evaluated in the framework of performance-based earthquake engineering, that is, via integration of site’s probabilistic hazard and structural fragility. The former has been computed consistently with the official hazard model for Italy that is also used to define design actions in the code. The latter has been addressed via nonlinear dynamic analysis of three-dimensional numerical structural models. Results indicate that, generally, design procedures are such that seismic structural reliability tends to decrease with increasing seismic hazard of the building site, despite the homogeneous return period of exceedance of the design seismic ground-motion.     

Quantification of Linked Column Frame Seismic Performance Factors for Use in Seismic Design

Previous research has proposed the Linked Column Frame (LCF) as a lateral load-resisting system capable of providing rapid return to occupancy for buildings impacted by moderate earthquake events and collapse prevention in very large events. The LCF consists of flexible moment frames (MF) and linked columns (LC), which are closely spaced dual columns interconnected with bolted links. The linked columns (LC) are designed to limit seismic forces and provide energy dissipation through yielding of the links, while preventing damage to the moment frame under certain earthquake hazard levels. The proposed design procedure ensures the links of the linked column yield at a significantly lower story drift than the beams of the moment frame, enabling design of this system for two distinct performance states: rapid repair, where only link damage occurs and quick link replacement is possible; and collapse prevention, where both the linked column and moment frame may be damaged.

Here, the seismic performance factors for the LCF system, including the response modification factor, R, the system over-strength factor, Ω₀, and the deflection amplification factor, C_d, are established following the procedures described in FEMA P695 [2009]. These parameters are necessary for inclusion of the system in the building code. This work describes the development of archetype structures, numerical models of the LCF systems, incremental dynamic analyses, and interpretation of the results. From the results, it is recommended that R, Ω₀, and C_d values of 8, 3, and 5.5 be used for seismic design of the LCF system. A height limit of 35 m (115ft) is recommended at this time as taller LCFs are not considered in this study.     

Seismic Design of MRF-EBF Dual Systems with Vertical Links: EC8 vs Plastic Design

Despite the fact that Eccentrically Braced Frames with Vertical Links (VL-EBFs), also referred to as inverted Y-scheme, are codified in Eurocode 8, the issues related to their seismic response and design have not been widely investigated, so that design criteria commonly applied for Eccentrically Braced Frames with Horizontal Links (HL-EBFs) are commonly applied. However, the Theory of Plastic Mechanism Control (TPMC) has been recently extended to the case of VL-EBFs. The aims of this article, on one hand, are to provide a further validation of the recently proposed design procedure, based on TPMC, and, on the other hand, are to compare the seismic performance of dual systems composed by a moment-resisting part and VL-EBF part designed by means of TPMC with those occurring when Eurocode 8 design criteria are applied. The validation of the proposed design procedure is carried out by means of Incremental Dynamic Analyses (IDA). The main purpose of such analyses is the check of the fulfilment of the design goal of TPMC, i.e., the development of a pattern of yielding consistent with the collapse mechanism of global type. Such mechanism is universally recognized as the one leading to the highest energy dissipation capacity. In case of MRF-EBF dual systems, it is characterized by the yielding of all the links and all the beams at their ends. Conversely, all the columns and the diagonal braces remain in elastic range. Obviously, exception is made for the base sections of first story columns. In particular, two case studies are analyzed which are characterized by a different number of stories. Each building structure is designed according to both TPMC and Eurocode 8 provisions. The seismic response obtained is investigated by both push-over and IDA analyses. The attention is focused on the pattern of yielding obtained, the maximum interstory drift demand, the link plastic rotation demand and sharing of the seismic base shear between the moment-resisting part and the bracing part of the structural system. The results obtained point out improvement of the seismic response, compared to Eurocode 8 provisions, achieved by means of TPMC.     

Full-Scale Experimental Testing of Retrofitting Techniques in Portuguese “Pombalino” Traditional Timber Frame Walls

Traditional timber frame walls are constructive elements representative of different timber frame buildings, well known as efficient seismic-resistant structures. They were adopted as a seismic-resistant solution in Lisbon’s reconstruction after the 1755 earthquake. To preserve these structures, a better knowledge of their seismic behavior is important and can give indications about possible retrofitting techniques. This article provides a study on possible retrofitting techniques adopting traditional solutions (bolts and steel plates). Static cyclic tests were performed on retrofitted traditional timber frame walls. The experimental results showed the overall good seismic performance of steel plates and the more ductile behavior of bolts retrofitting.     

Seismic Tests and Numerical Modeling of a Rolling-ball Isolation System

For the seismic isolation of light structures, the use of laminated rubber bearings is neither economical nor, for most cases, technically suited. For the isolation of this type of structure a new system, consisting of steel balls rolling on rubber tracks, has been developed at TARRC (Tun Abdul Razak Research Centre).

This article presents the results of experimental tests carried out for the characterization of the behavior of this new device. A numerical model is also proposed that can be used to assess the seismic response of structures with this isolation system.

Comparison of the predictions of the numerical model with the experimental data shows that the model is adequate to perform the correct assessment of the seismic response of isolated structures. The results of the experimental campaign of shaking-table tests, as well as the numerical simulations, show that there is an effective reduction of the acceleration levels induced in the isolated structures.     

Seismic Fragility Evaluation of RC Frame Structures Retrofitted with Controlled Concrete Rocking Column and Damping Technique

Acceleration response of simple yielding structure is proportional to its own weight, but it is limited by yield strength. Thus, using rocking columns that reduces global yield strength, a limited acceleration is achieved. However, the displacement becomes large due to lower strength and higher inelasticity, but it can be controlled by adding damping. Performing fragility analyses, the seismic response of R/C frame structures with rocking columns and viscous dampers is investigated. Near field MCEER ground motions are considered. The analyses show that the story accelerations are reduced by using rocking columns, while the story displacements are controlled by using viscous dampers.     

Mediterranean trade of the most widespread Roman volcanic millstones from Italy and petrochemical markers of their raw materials

The petrochemical study of millstones can contribute to improve the archaeological research into reconstruction of ancient communication routes and trade networks. Volcanic rocks are geographically restricted and rather rare in the Mediterranean regions, and during the Roman period Italian volcanoes were important sources of raw materials for millstones, so the task of determining their geological origin is relatively straightforward. The Italian vesicular volcanics most frequently employed for this purpose were: trachytes from Euganean Hills (Veneto), leucite-bearing lavas from the Vulsini Volcanic District (Latium), basic-intermediate leucite-bearing lavas from Somma-Vesuvius (Campania), silica undersaturated lavas from Monte Vulture Volcano (Basilicata), a rhyolitic ignimbrite from Sardinia and basic products from Mount Etna and the island of Pantelleria (Sicily). This paper contains a general outline of the trade network for each volcanic typology used for millstones during the Roman period – updated with data concerning the leucite-bearing lavic items discovered in the archaeological sites of the ancient Cuicul (now Djemila, Algeria) – together with a summary of their petrographic and geochemical features.     

DIAPHRAGM ACTION OF SANDWICH PANELS IN PIN-JOINTED STEEL STRUCTURES: A SEISMIC STUDY

The paper focuses on the seismic response of steel pin-jointed frames braced by lightweight cladding panels. In particular, with the aim to investigate the performance of such a structural scheme when acting as a dissipative system, a wide numerical study has been developed. It is based upon available shear tests on screwed sandwich panels, whose experimental cyclic responses are properly incorporated into a scope-oriented, computer program. The goal is firstly to check the possibility of using cladding panels as shear diaphragms in seismic areas and then to assess an appropriate design behaviour factor, accounting for their actual hysteretic response. Key findings from the nonlinear dynamic analyses are: (1) a portal frame steel building in a low-medium seismicity zone may be braced by common cladding panels, completely avoiding the use of other bracing systems; (2) this structural solution, if compared with a conventional one, appears to be more efficient and cost-effective, giving rise to a weight saving which, in the case under examination, reaches a value of about 20%; (3) on the basis of the numerical study a design behaviour factor q _d =2 seems to be realistic for such a structural typology.     

SEISMIC HAZARD ASSESSMENT IN FLORENCE CITY ITALY

A seismic hazard analysis of Florence city was performed in the frame of a project concerning the dynamic behaviour of cable-stayed bridges. Both a probabilistic approach and a methodology based on the use of a local macroseismic catalogue were applied. A local catalogue was expressly compiled for this purpose, to collect the macroseismic intensities actually observed at the site as a result of past earthquakes. This sort of catalogue is an independent tool to verify the assumptions of the probabilistic approach (seismic zoning, earthquake recurrence relation, attenuation model), though it can supply results in terms of macroseismic intensity only and reflects the effective seismic history at the site, without taking into account any variability. The Cornell' methodology was used to assess probabilistic hazard in terms of macroseismic intensity, peak ground acceleration, peak ground velocity, and pseudovelocity uniform response spectra. The local catalogue points out level VII of the Mercalli-Cancani-Sieberg scale (MCS) as the maximum intensity historically observed in Florence. The probabilistic approach leads to the consideration of intensity VIII MCS as the maximum credible for the city. The probabilistic analysis in terms of ground motion was performed using attenuation relations estimated for alluvium sites, since the geology of Florence area is represented by fluvial and lacustrine deposits of various thickness. Peak ground acceleration values with 90% non exceedence probability in 50 and 500 years are respectively 145 and 219 cm/s's for a shallow alluvium site, and 95 and 157 cm/s's for a deep alluvium site; the corresponding peak ground velocity values for sites located on alluvium are 6.41 and 11.76 cm/s. Uniform response spectra are provided for shallow and deep alluvium sites, according to frequency-dependent attenuation relations estimated from strong Italian earthquakes.     

A Novel Procedure for Simplified Nonlinear Numerical Modeling of Structural Units in Masonry Aggregates

ABSTRACT

Historical centers are always composed of masonry building aggregates often designed without respecting seismic design criteria. The current seismic Italian code does not foresee a clear calculation method to predict their static nonlinear behavior. For this reason, in this article the seismic response of structural units into masonry aggregates has been predicted through a simplified modeling approach. The implemented procedure has been calibrated on the results of a numerical model performed by using the Equivalent Frame Method (EFM), implemented within a Finite Element Method (FEM) calculation program, used to investigate a basic building compound representative of the constructive techniques developed in the past decades in the Southern Italy.

First, the whole aggregate has been modeled and analyzed in the nonlinear static field in order to evaluate the seismic behavior of both intermediate and head structural units.

Later on, the seismic response of these structural units, considered as isolated structures, has been assessed by considering in simplified way their position in the aggregate, as well as the influence of other constructions.

Finally, the achieved results on the above single analysis cases have been compared with those deriving from the investigation of the whole building compound, allowing to confirm the effectiveness of the proposed novel analysis procedure.