Seismic Design of MRF-EBF Dual Systems with Vertical Links: EC8 vs Plastic Design

Despite the fact that Eccentrically Braced Frames with Vertical Links (VL-EBFs), also referred to as inverted Y-scheme, are codified in Eurocode 8, the issues related to their seismic response and design have not been widely investigated, so that design criteria commonly applied for Eccentrically Braced Frames with Horizontal Links (HL-EBFs) are commonly applied. However, the Theory of Plastic Mechanism Control (TPMC) has been recently extended to the case of VL-EBFs. The aims of this article, on one hand, are to provide a further validation of the recently proposed design procedure, based on TPMC, and, on the other hand, are to compare the seismic performance of dual systems composed by a moment-resisting part and VL-EBF part designed by means of TPMC with those occurring when Eurocode 8 design criteria are applied. The validation of the proposed design procedure is carried out by means of Incremental Dynamic Analyses (IDA). The main purpose of such analyses is the check of the fulfilment of the design goal of TPMC, i.e., the development of a pattern of yielding consistent with the collapse mechanism of global type. Such mechanism is universally recognized as the one leading to the highest energy dissipation capacity. In case of MRF-EBF dual systems, it is characterized by the yielding of all the links and all the beams at their ends. Conversely, all the columns and the diagonal braces remain in elastic range. Obviously, exception is made for the base sections of first story columns. In particular, two case studies are analyzed which are characterized by a different number of stories. Each building structure is designed according to both TPMC and Eurocode 8 provisions. The seismic response obtained is investigated by both push-over and IDA analyses. The attention is focused on the pattern of yielding obtained, the maximum interstory drift demand, the link plastic rotation demand and sharing of the seismic base shear between the moment-resisting part and the bracing part of the structural system. The results obtained point out improvement of the seismic response, compared to Eurocode 8 provisions, achieved by means of TPMC.     

Direct Displacement-Based Design of Glulam Timber Frame Buildings

We introduce a direct Displacement-Based Design methodology for glued laminated timber portal frames with moment-resisting doweled joints. We propose practical expressions to estimate ultimate target displacement and equivalent viscous damping, and we demonstrate that these expressions provide prior values that are close to those obtained a posteriori using a more refined model. Applied to case studies, the method yields base-shear forces lower than those obtained using the force-based approach of Eurocode 8. This is due to the high dissipation capacity of the specific connection technology, which apparently is conservatively accounted for in the q-factor of Eurocode 8.     

Direct Displacement-Based Design of Buildings with Different Seismic Isolation Systems

A displacement-based design (DBD) procedure for buildings equipped with different seismic isolation systems is proposed. It has been derived from the Direct Dispaced-Based Design (DDBD) method recently developed by Priestley et al. [2007] Priestley, M. J. N., Calvi, G. M. and Kowalsky, M. J. 2007. Displacement-Based Seismic Design of Structures, Pavia, , Italy: IUSS Press.  [Google Scholar]. The key aspect of the proposed procedure is the definition of a target displacement profile for the structure. It is assigned by the designer to achieve given performance levels, expressed in terms of maximum displacement of the isolation system and maximum interstory drift. The proposed design procedure has been developed for four different idealized force-displacement relationships, which can describe the cyclic response of a wide variety of isolation systems, including: (i) Lead-Rubber Bearings (LRB); (ii) High-Damping Rubber Bearings (HDRB); (iii) Friction Pendulum Systems (FPS); and (iv) Combinations of lubricated Flat Sliding Bearings (FSB) with different re-centering and/or energy dissipating auxiliary devices. In this article, the background and implementation of the design procedure is presented first. It is followed by the results of validation studies based on nonlinear time-history analyses on different design configurations of base isolated buildings.     

Cyclic Performance of an Elliptical-Shaped Damper with Shear Diaphragms in Chevron Braced Steel Frames

Several advantages of yielding dampers in controlling seismic energy have attracted the attention of many researchers in designing new buildings and retrofitting existing structures. In recent decades, various shapes and substances of such dampers have been used in engineering structures and their behavioral features, including the energy dissipating capacities, have been assessed. In this article, a novel method is presented to obtain the design relationship of two types of yielding elliptical dampers in terms of their selected geometric properties, i.e. distance between the shear diaphragms or virtual diameter and thickness. In addition, two different elliptical-shaped steel dampers equipped with the shear diaphragms are proposed and modeled using the finite element software ABAQUS and their performances are investigated. Then, 30 and 25 models, respectively, of the first and second types are studied using pushover analysis. The designed dampers considering the proposed relationships are used in two chevron braced steel frames placed between the bracing and the beam. Due to their desirable efficiency in energy dissipation and increase in the equivalent viscous damping of the frame, better efficiency is achieved in the modified damper with easier fabrication.     

Behavior Factor for Performance-Based Seismic Design of Plane Steel Moment Resisting Frames

Simplified expressions to estimate the behavior factor of plane steel moment resisting frames are proposed, based on statistical analysis of the results of thousands of nonlinear dynamic analyses. The influence on this factor of specific structural parameters, such as the number of stories, the number of bays, and the capacity design factor of a steel frame, is studied in detail. The proposed factor describes the seismic strength requirements in order to restrict maximum storey ductility to a predefined value. Interrelation studies between maximum storey ductility and the Park-Ang damage index are also provided for the damage-based interpretation of the performance levels under consideration. Realistic design examples serve to demonstrate the ability of the proposed factor to convert conventional force-based design to a direct performance-based seismic design procedure.     

Seismic Vulnerability Assessment of Modular Steel Buildings

Contemporary seismic design is based on dissipating earthquake energy through significant inelastic deformations. This study aims at developing an understanding of the inelastic behavior of braced frames of modular steel buildings (MSBs) and assessing their seismic demands and capacities. Incremental dynamic analysis is performed on typical MSB frames. The analysis accounts for their unique detailing requirements. Maximum inter-story drift and peak global roof drift were adopted as critical response parameters. The study revealed significant global seismic capacity and a satisfactory performance at design intensity levels. High concentration of inelasticity due to limited redistribution of internal forces was observed.     

Equivalent Damping Ratio Equations in Support of Displacement-Based Seismic Design for Pile-Supported Wharves

This study primarily proposes new equivalent damping ratio equations based on Jacobsen’s approach for displacement-based seismic design of pile-supported wharves to account for wharf configurations and soil-pile interaction. It is found that Pivot hysteresis model and Masing rule can accurately capture nonlinear behavior of concrete and steel wharves, respectively. To verify applicability of proposed equations, analyses were conducted to three typical wharves to make a comparison of maximum displacements obtained from nonlinear time-history analyses and substitute structure method with various damping equations. The verification reveals proposed equations are better than those in practice for their higher precision in determining displacements.     

Probabilistic Calibration and Experimental Validation of the Seismic Design Criteria for One-Story Concrete Frames

This article investigates the seismic performance of one-story reinforced concrete structures for industrial buildings. To this aim, the seismic response of two structural prototypes, a cast-in-situ monolithic frame and a precast hinged frame, is compared for four different levels of translatory stiffness and seismic capacity. For these structures an incremental nonlinear dynamic analysis is performed within a Monte Carlo probabilistic simulation. The results obtained from the probabilistic analysis prove that precast structures have the same seismic capacity of the corresponding cast-in-situ structures and confirm the overall goodness of the design criteria proposed by Eurocode 8, even if a noteworthy dependency of the actual structural behavior from the prescribed response spectrum is pointed out.

The experimental verification of these theoretical results is searched for by means of pseudodynamic tests on full-scale structures. The results of these tests confirm the overall equivalence of the seismic behavior of precast and cast-in-situ structures. Moreover, two additional prototypes have been designed to investigate the seismic behavior of precast structures with roof elements placed side by side. The results of these further tests show that an effective horizontal diaphragm action can be activated even if the roof elements are not connected among them, and confirm the expected good seismic performance of these precast systems. Finally, the results of the experimental tests are compared with those obtained from nonlinear structural analyses. The good agreement between numerical and experimental results confirms the accuracy of the theoretical model and, with it, the results of the probabilistic investigation.     

A Critical Review of European and American Provisions for the Seismic Assessment of Existing Steel Moment-Resisting Frame Buildings

The publication of Part 3 of Eurocode 8 (EC8-3), dedicated to the seismic assessment of existing buildings, took place a decade ago. However, its application in engineering practice has been limited. Moreover, no studies have been conducted regarding the application of EC8-3 to steel structures. In this paper, a critical review and practical application of EC8-3 and ASCE41-13 are carried out. Issues related to the definition of the performance requirements, compliance criteria, and the consistency of the analysis procedures proposed by both standards are identified. Conceptual differences between both documents are highlighted, and several inconsistencies in EC8-3 are discussed.     

Numerical Simulation and Seismic Fragility Analysis of a Self-Centering Steel MRF with Web Friction Devices

This article presents the seismic fragility analysis of a self-centering steel moment-resisting frame (SC-MRF) with web friction devices. A detailed numerical model of the SC frame was developed using the Open System for Earthquake Engineering Simulation (OpenSees) and the elastoplastic responses of the SC-MRF were studied, including the strength degradation under cyclic loading, tendon rupture, beam buckling, bolt bearing and friction loss, etc. The proposed simulation approach is validated by comparing the simulated results with those in existing hybrid-simulation tests, quasi-static pushover test and low cyclic tests, where good agreement is observed. In addition to the well-established performance limit states (i.e., immediate occupancy, collapse prevention and global dynamic instability), two unique performance limit states (i.e., the recentering and repairable limit states) are defined for the SC-MRF. Finally, incremental dynamic analyses are conducted to evaluate the seismic fragilities regarding the five performance limit states.     

Seismic Performance and Modeling of a Half-Scale Base-Isolated Wood Frame Building

The concept of base isolation is a century old, but application to civil engineering structures has only occurred over the last several decades. Application to light-frame wood buildings in North America has been virtually non existent with one notable exception. This article quantitatively examines issues associated with application of base isolation in light-frame wood building systems including: (1) constructability issues related to ensuring sufficient in-plane floor diaphragm stiffness to transfer shear from the superstructure to the isolation system; (2) evaluation of experimental seismic performance of a half-scale base-isolated light-frame wood building; and (3) development of a displacement–based seismic design method and numerical model and their comparison with experimental results. The results of the study demonstrate that friction pendulum system (FPS) bearings offer a technically viable passive seismic protection system for light-frame wood buildings in high seismic zones. Specifically, the amount and method of stiffening the floor diaphragm is not unreasonable, given that the inter-story drift and accelerations at the upper level of the tested building were very low, thus resulting in the expectation of virtually no structural, non structural, or contents damage in low-rise wood frame buildings. The nonlinear dynamic model was able to replicate both the isolation layer and superstructure movement with good accuracy. The displacement-based design method was proven to be a viable tool to estimate the inter-story drift of the superstructure. These tools further underscore the potential of applying base isolation systems for application to North America's largest building type.