Stress‐dependent transport properties of fractured arkosic sandstone

We measure the fluid transport properties of microfractures and macrofractures in low‐porosity polyphase sandstone and investigate the controls of in situ stress state on fluid flow conduits in fractured rock. For this study, the permeability and porosity of the Punchbowl Formation sandstone, a hydrothermally altered arkosic sandstone, were measured and mapped in stress space under intact, microfractured, and macrofractured deformation states. In contrast to crystalline and other sedimentary rocks, the distributed intragranular and grain‐boundary microfracturing that precedes macroscopic fracture formation has little effect on the fluid transport properties. The permeability and porosity of microfractured and intact sandstone depend strongly on mean stress and are relatively insensitive to differential stress and proximity to the frictional sliding envelope. Porosity variations occur by elastic pore closure with intergranular sliding and pore collapse caused by microfracturing along weakly cemented grain contacts. The macroscopic fractured samples are best described as a two‐component system consisting (i) a tabular fracture with a 0.5‐mm‐thick gouge zone bounded by 1 mm thick zones of concentrated transgranular and intragranular microfractures and (ii) damaged sandstone. Using bulk porosity and permeability measurements and finite element methods models, we show that the tabular fracture is at least two orders of magnitude more permeable than the host rock at mean stresses up to 90 MPa. Further, we show that the tabular fracture zone dilates as the stress state approaches the friction envelope resulting in up to a three order of magnitude increase in fracture permeability. These results indicate that the enhanced and stress‐sensitive permeability in fault damage zones and sedimentary basins composed of arkosic sandstones will be controlled by the distribution of macroscopic fractures rather than microfractures.     

Evaluation of recoverable energy potential from enhanced geothermal systems: a sensitivity analysis in a poro‐thermo‐elastic framework

This study presents application of an efficient approach to simulate fluid flow and heat transfer in naturally fractured geothermal reservoirs. Fluid flow is simulated by combining single continuum and discrete fracture approaches. The local thermal nonequilibrium approach is used to simulate heat transfer by conduction in the rock matrix and convection (including conduction) in the fluid. Fluid flow and heat transfer models are integrated within a coupled poro‐thermo‐elastic framework. The developed model is used to evaluate the long‐term response of a geothermal reservoir with specific boundary conditions and injection/production schedule. A comparative study and a sensitivity analysis are carried out to evaluate the capability of the integrated approach and understand the degree by which different reservoir parameters affect thermal depletion of Soultz geothermal reservoir, respectively. Also observed, there exists an optimum fracture permeability after which the reservoir stimulation does not change the recovery factor significantly. Estimation of fluid temperature by the assumption of local thermal nonequilibrium heat transfer between the fracture fluid and the rock matrix gives fluid temperature of about 3°C less than that of estimated by thermal equilibrium heat transfer at early stage of hot water production.     

Timescales for reaching steady-state fluid flow in systems perturbed by formation of highly permeable faults

We consider the case of an isothermal, fluid‐saturated, homogeneous rock layer with transverse fluid flow driven by an imposed constant fluid pressure gradient. A rupture in the centre of the rock layer generates a highly permeable fault and results in a change of the initially homogeneous permeability distribution. This leads to a perturbation of the fluid flow field and its gradual transition to a new steady‐state corresponding to the new permeability distribution. An examination of this transitional process permits us to obtain an analytical estimation of the transition stage duration. The application of the results obtained to km‐scale faults in crystalline rock bodies leads to the conclusion that the evolution of the fluid velocity field is rather rapid compared with geological timescales.     

Permeability evolution in sorbing media: analogies between organic‐rich shale and coal

Shale gas reservoirs like coalbed methane (CBM) reservoirs are promising targets for geological sequestration of carbon dioxide (CO₂). However, the evolution of permeability in shale reservoirs on injection of CO₂ is poorly understood unlike CBM reservoirs. In this study, we report measurements of permeability evolution in shales infiltrated separately by nonsorbing (He) and sorbing (CO₂) gases under varying gas pressures and confining stresses. Experiments are completed on Pennsylvanian shales containing both natural and artificial fractures under nonpropped and propped conditions. We use the models for permeability evolution in coal (Journal of Petroleum Science and Engineering, Under Revision) to codify the permeability evolution observed in the shale samples. It is observed that for a naturally fractured shale, the He permeability increases by approximately 15% as effective stress is reduced by increasing the gas pressure from 1 MPa to 6 MPa at constant confining stress of 10 MPa. Conversely, the CO₂ permeability reduces by a factor of two under similar conditions. A second core is split with a fine saw to create a smooth artificial fracture and the permeabilities are measured for both nonpropped and propped fractures. The He permeability of a propped artificial fracture is approximately 2‐ to 3fold that of the nonpropped fracture. The He permeability increases with gas pressure under constant confining stress for both nonpropped and propped cases. However, the CO₂ permeability of the propped fracture decreases by between one‐half to one‐third as the gas pressure increases from 1 to 4 MPa at constant confining stress. Interestingly, the CO₂ permeability of nonpropped fracture increases with gas pressure at constant confining stress. The permeability evolution of nonpropped and propped artificial fractures in shale is found to be similar to those observed in coals but the extent of permeability reduction by swelling is much lower in shale due to its lower organic content. Optical profilometry is used to quantify the surface roughness. The changes in surface roughness indicate significant influence of proppant indentation on fracture surface in the shale sample. The trends of permeability evolution on injection of CO₂ in coals and shales are found analogous; therefore, the permeability evolution models previously developed for coals are adopted to explain the permeability evolution in shales.     

Pore pressure evolution and fluid flow during visco‐elastic single‐layer buckle folding

Pore pressure and fluid flow during the deformational history of geologic structures are directly influenced by tectonic deformation events. In this contribution, 2D plane strain finite element analysis is used to study the influence of different permeability distributions on the pore pressure field and associated flow regimes during the evolution of visco‐elastic single‐layer buckle folds. The buckling‐induced fluid flow regimes indicate that flow directions and, to a lesser degree, their magnitudes vary significantly throughout the deformation and as a function of the stratigraphic permeability distribution. The modelling results suggest that the volumetric strain and the permeability distribution significantly affect the resulting flow regime at different stages of fold development. For homogeneous permeability models (k > 10^?21 m²), low strain results in a mostly pervasive fluid flow regime and is in agreement with previous studies. For larger strain conditions, fluid focusing occurs in the buckling layer towards the top of the fold hinge. For low permeabilities (<10^?21 m²), local focused flow regimes inside the buckling layer emerge throughout the deformation history. For models featuring a low‐permeability layer embedded in a high‐permeability matrix or sandwiched between high‐permeability layers, focused flow regimes inside the folded layer result throughout the deformation history, but with significant differences in the flow vectors of the surrounding layers. Fluid flow vectors induced by the fold can result in different, even reversed, directions depending on the amount of strain. In summary, fluid flow regimes during single‐layer buckling can change from pervasive to focused and fluid flow vectors can be opposite at different strain levels, that is the flow vectors change significantly through time. Thus, a complete understanding of fluid flow regimes associated with single‐layer buckle folds requires consideration of the complete deformation history of the fold.     

Fluid effect on hydraulic fracture propagation behavior: a comparison between water and supercritical CO2‐like fluid

The initiation of hydraulic fractures during fluid injection in deep formations can be either engineered or induced unintentionally. Upon injection of CO₂, the pore fluids in deep formations can be changed from oil/saline water to CO₂ or CO₂ dominated. The type of fluid is important not only because the fluid must fracture the rock, but also because rocks saturated with different pore fluids behave differently. We investigated the influence of fluid properties on fracture propagation behavior by using the cohesive zone model in conjunction with a poroelasticity model. Simulation results indicate that the pore pressure fields are very different for different pore fluids even when the initial field conditions and injection schemes (rate and time) are kept the same. Low viscosity fluids with properties of supercritical CO₂ will create relatively thin and much shorter fractures in comparison with fluids exhibiting properties of water under similar injection schemes. Two significant times are recognized during fracture propagation: the time at which a crack ceases opening and the later time point at which a crack ceases propagating. These times are very different for different fluids. Both fluid compressibility and viscosity influence fracture propagation, with viscosity being the more important property. Viscosity can greatly affect hydraulic conductivity and the leak‐off coefficient. This analysis assumes the in‐situ pore fluid and injected fluid are the same and the pore space is 100% saturated by that fluid at the beginning of the simulation.     

Effective gas permeability of Tight Gas Sandstones as a function of capillary pressure – a non‐steady‐state approach

Single‐ and two‐phase (gas/water) fluid transport in tight sandstones has been studied in a series of permeability tests on core plugs of nine tight sandstones of the southern North Sea. Absolute (Klinkenberg‐corrected) gas permeability coefficients (k_gas__inf) ranged between 3.8 × 10^?16 and 6.2 × 10^?19 m² and decreased with increasing confining pressure (10–30 MPa) by a factor 3–5. Klinkenberg‐corrected (intrinsic) gas permeability coefficients were consistently higher by factors from 1.4 to 10 than permeability coefficients determined with water. Non‐steady‐state two‐phase (He/water) flow experiments conducted up to differential pressures of 10 MPa document the dynamically changing conductivity for the gas phase, which is primarily capillary‐controlled (drainage and imbibition). Effective gas permeability coefficients in the two‐phase flow tests ranged between 1.1 × 10^?17 and 2.5 × 10^?22 m², corresponding to relative gas permeabilities of 0.03% and 10%. In the early phase of the nonstationary flow regime (before establishment of steady‐state conditions), they may be substantially (>50%) lower. Effective gas permeability measurements are affected by the following factors: (i) Capillary‐controlled drainage/imbibition, (ii) viscous–dynamic effects (iii) and slip flow.     

Physical properties of carbonate fault rocks,fucino basin (Central Italy): implications for fault seal in platform carbonates

We documented the porosity, permeability, pore geometry, pore type, textural anisotropy, and capillary pressure of carbonate rock samples collected along basin‐bounding normal faults in central Italy. The study samples consist of one Mesozoic platform carbonate host rock with low porosity and permeability, four fractured host rocks of the damage zones, and four fault rocks of the fault cores. The four fractured samples have high secondary porosity, due to elongated, connected, soft pores that provide fluid pathways in the damage zone. We modeled this zone as an elastic cracked medium, and used the Budiansky–O'Connell correlation to compute its permeability from the measured elastic moduli. This correlation can be applied only to fractured rocks with large secondary porosity and high‐aspect ratio pores. The four fault rock samples are made up of survivor clasts embedded in fine carbonate matrices and cements with sub‐spherical, stiff pores. The low porosity and permeability of these rocks, and their high values of capillary pressure, are consistent with the fault core sealing as much as 77 and 140 m of gas and oil columns, respectively. We modeled the fault core as a granular medium, and used the Kozeny–Carmen correlation, assigning the value of 5 to the Kozeny constant, to compute its permeability from the measured porosities and pore radii. The permeability structure of the normal faults is composed of two main units with unique hydraulic characteristics: a granular fault core that acts as a seal to cross‐fault fluid flow, and an elastic cracked damage zone that surrounds the core and forms a conduit for fluid flow. Transient pathways for along‐fault fluid flow may form in the fault core during seismic faulting due to the formation of opening‐mode fractures within the cemented fault rocks.     

Geometry‐coupled reactive fluid transport at the fracture scale: application to CO2 geologic storage

Water acidification follows CO₂ injection and leads to reactive fluid transport through pores and rock fractures, with potential implications to reservoirs and wells in CO₂ geologic storage and enhanced oil recovery. Kinetic rate laws for dissolution reactions in calcite and anorthite are combined with the Navier‐Stokes law and advection–diffusion transport to perform geometry‐coupled numerical simulations in order to study the evolution of chemical reactions, species concentration, and fracture morphology. Results are summarized as a function of two dimensionless parameters: the Damköhler number Da which is the ratio between advection and reaction times, and the transverse Peclet number Pe defined as the ratio between the time for diffusion across the fracture and the time for advection along the fracture. Reactant species are readily consumed near the inlet in a carbonate reservoir when the flow velocity is low (low transverse Peclet number and Da > 10^?1). At high flow velocities, diffusion fails to homogenize the concentration field across the fracture (high transverse Peclet number Pe > 10^?1). When the reaction rate is low as in anorthite reservoirs (Da < 10^?1), reactant species are more readily transported toward the outlet. At a given Peclet number, a lower Damköhler number causes the flow channel to experience a more uniform aperture enlargement along the length of the fracture. When the length‐to‐aperture ratio is sufficiently large, say l/d > 30, the system response resembles the solution for 1D reactive fluid transport. A decreased length‐to‐aperture ratio slows the diffusive transport of reactant species to the mineral fracture surface, and analyses of fracture networks must take into consideration both the length and slenderness of individual fractures in addition to Pe and Da numbers.     

Phase‐field modeling of epitaxial growth of polycrystalline quartz veins in hydrothermal experiments

Mineral precipitation in an open fracture plays a crucial role in the evolution of fracture permeability in rocks, and the microstructural development and precipitation rates are closely linked to fluid composition, the kind of host rock as well as temperature and pressure. In this study, we develop a continuum thermodynamic model to understand polycrystalline growth of quartz aggregates from the rock surface. The adapted multiphase‐field model takes into consideration both the absolute growth rate as a function of the driving force of the reaction (free energy differences between solid and liquid phases), and the equilibrium crystal shape (Wulff shape). In addition, we realize the anisotropic shape of the quartz crystal by introducing relative growth rates of the facets. The missing parameters of the model, including surface energy and relative growth rates, are determined by detailed analysis of the crystal shapes and crystallographic orientation of polycrystalline quartz aggregates in veins synthesized in previous hydrothermal experiments. The growth simulations were carried out for a single crystal and for grain aggregates from a rock surface. The single crystal simulation reveals the importance of crystal facetting on the growth rate; for example, growth velocity in the c‐axis direction drops by a factor of ~9 when the faceting is complete. The textures produced by the polycrystal simulations are similar to those observed in the hydrothermal experiments, including the number of surviving grains and crystallographic preferred orientations as a function of the distance from the rock wall. Our model and the methods to define its parameters provide a basis for further investigation of fracture sealing under varying conditions.     

Precipitation of fracture fillings and cements in the Buntsandstein (NW Germany)

The relationship between fracturing and fracture filling in opening‐mode fractures in the Triassic Buntsandstein in the Lower Saxony Basin (LSB; NW Germany) has been studied by an integration of petrographic and structural analysis of core samples, strontium isotope analysis and microthermometry on fluid inclusions. This revealed the relationship between the timing of the fracturing and the precipitation of different mineral phases in the fractures by constraining the precipitation conditions and considering the possible fluid transport mechanisms. The core was studied from four different boreholes, located in different structural settings across the LSB. In the core samples from the four boreholes, fractures filled with calcite, quartz and anhydrite were found, in addition to pore‐filling calcite cementation. In boreholes 2 and 3, calcite‐filled fractures have a fibrous microstructure whereas in borehole 1, fractures are filled with elongate‐blocky calcite crystals. Anhydrite‐filled fractures have, in all samples, a blocky to elongate‐blocky microstructure. Fractures that are filled with quartz are observed in borehole 2 only where the quartz crystals are ‘stretched’ with an elongated habit. Fluid inclusion microthermometry of fracturing‐filling quartz crystals showed that quartz precipitation took place at temperatures of at least 140°C, from a fluid with NaCl–CaCl₂–H₂O composition. Melting phases are meta‐stable and suggest growth from high salinity formation water. Strontium isotopes, measured in leached host rock, indicate that, in boreholes 2 and 3, the fluid which precipitated the calcite cements and calcite‐filled fractures is most likely locally derived whereas in borehole 1, the ⁸⁷Sr/⁸⁶Sr ratios from the pore‐filling cements and in the elongate‐blocky calcite‐filled fracture can only be explained by mixing with externally derived fluids. The elongate‐blocky anhydrite‐filled fractures, present in boreholes 1, 3 and 4, precipitated from a mixture of locally derived pore fluids and a significant quantity of fluid with a lower, less radiogenic, ⁸⁷Sr/⁸⁶Sr ratio. Taking into account the structural evolution of the basin and accompanying salt tectonics, it is likely that the underlying Zechstein is a source for the less radiogenic fluids. Based on the samples in the LSB, it is probable that fibrous fracture fillings in sedimentary rocks most likely developed from locally derived pore fluids whereas elongate‐blocky fracture fillings with smooth walls developed from externally derived pore fluids.     

Investigation of coupled hydraulic–geomechanical processes at the KTB site: pressure‐dependent characteristics of a long‐term pump test and elastic interpretation using a geomechanical facies model

The German Continental Deep Drilling Program comprising a pilot borehole down to 4000 m and a main borehole down to 9101 m in southeast Germany (KTB) is continuing to provide a unique opportunity for the identification of important factors and processes in deep‐seated fluid and energy transfer. In situ stress conditions significantly impact flow, transport and exchange characteristics of fracture networks that dominate the permeability of crystalline reservoir rocks. In this paper, several scales of information are combined to present a fully three‐dimensional hydraulic finite element model of the principal KTB fault zones, and linked to a geomechanical model describing the alteration of the hydraulic parameters with stress changes caused by fluid extraction. The concept of geomechanical facies is introduced to define and characterize architectural elements in the subsurface system. Evaluation of a long‐term pump test in the KTB pilot hole, June 2002–July 2003, coupled with a geomechanical model gives an insight into some of the elastic and nonelastic processes controlling hydraulic transport in the basement rocks. Trends in the decline of the permeability and the degree of storage in the system could only partially be explained by elastic processes, clearly indicating the importance of nonelastic processes. A number of inelastic processes are suggested as areas for further research.     

Fracture sealing and fluid overpressures in limestones of the Jabal Akhdar dome,Oman mountains

Fractures are important conduits for fluid flow in the Earth's crust. To better understand the spatial and temporal relations among fracturing, fracture sealing, and fluid flow, we have studied fractures, faults, and veins in a large dome (Jabal Akhdar) in the Oman mountains. Our work combines the results of meso‐ and microstructural analyses and stable isotope analyses. Seven generations of fractures and veins have been identified in the carbonate‐dominated dome. The earliest generations of veins developed during extension and subsidence of the Mesozoic basin. These veins formed in the inclined segments of bedding‐parallel stylolites and in extensional fractures that are perpendicular to bedding (#1 and #2, respectively). These extension‐related veins are truncated by bedding‐parallel veins (#4) that formed during top‐to‐north bedding‐parallel shear of both the northern and southern limbs of the dome. These veins are consistent with a change in stress regime and may be related to an earlier generation of strongly deformed pinch‐and‐swell veins (#3) that are exposed locally on the southern limb of the dome. Normal faults contain a set of en‐echelon tension gashes (#5) and veins emplaced in dilational jogs along the fault planes (#6). In the northern part of the dome, veins (#7) associated with thrusts post‐date the normal faults. Samples of veins and their host rocks were analyzed to provide information on fluid‐rock interaction in the dome and the scale(s) of fluid movement. Oxygen isotope values range from +16.2 to +29.3‰; carbon isotope values range from 0 to +3.6‰. The results of the structural and isotopic analyses are consistent with the early veins (#2–#5) having precipitated from overpressured fluid in a isotopically rock‐buffered system. During normal faulting (#5 and #6), a more open system allowed external fluid to infiltrate the dome at drained conditions and precipitate the youngest sets of veins (#6 and #7).     

A Large‐Scale Palaeopathological Study of Hip Fractures from Post‐Medieval Urban England

Hip fractures have high incidence rates in many current groups and are associated with high morbidity, mortality, and considerable expenditure. Although hip fractures associated with significant traumatic events can occur at any age, many hip fractures occur in older adults. To date, few hip fractures have been reported from archaeological skeletal material, and a number of hypotheses have been suggested for this. This research presents a comprehensive assessment of hip fractures in archaeological bone; 1597 adult (18+ years) skeletons from eight urban post‐medieval sites from England dating from the 18^th and 19^th centuries were recorded, and contemporary medical texts reviewed. This adult sample included 834 males and 652 females as well as 11 persons of undetermined sex. Ways of classifying and describing fractures in the clinical literature were reviewed and a methodology applicable to paleopathology determined. Of this sample, 15 (0.94%) had fractures in the femoral neck or intertrochanteric area: nine males, four females, and two individuals of undetermined sex. The numbers of fractures in males were interesting and most likely represent examples of accidental trauma as well as osteoporosis‐related fractures, the latter receiving growing awareness in recent clinical literature. Overall there was an age‐related trend with more individuals aged 50+ years with fractures than in other age categories. Underlying osteoporosis was potentially a complicating factor in five individuals and was likely associated with a vitamin D deficiency osteomalacia and a metastatic neoplastic condition in a further two cases. Fractures occurring close to the time of death and healed fractures were observed, indicating that the risk of mortality following this trauma was not consistent across this 18^th and 19^th century sample. Skeletal and historical evidence presented in this study indicate that the impact of hip fracture injuries varied, with survival likely linked to the fracture type. Copyright © 2016 John Wiley & Sons, Ltd.     

Long‐term stability of fracture systems and their behaviour as flow paths in uplifting granitic rocks from the Japanese orogenic field

In granitic rocks, fracture networks typically provide pathways for groundwater flow and solute transport that need to be understood to assess the long‐term performance of deep underground storage or disposal facilities such as radioactive waste repositories. However, relatively little is known about the long‐term processes of fracturing and/or the longevity of flow paths (FP) in granitic rocks distributed within orogenic belts. To clarify these issues, Japanese plutons of different ages and in situ fractures in granite at the Mizunami Underground Research Laboratory (MIU) located in central Japan were studied. Detailed structural characterization and geochemical analysis of in situ fracture fillings sampled from a depth of 300 m were carried out to clarify the relationship between fracturing and mineral infilling processes. Different plutons show identical episodes of fracturing and fracture filling, consisting of: brittle tensile fracturing, due to decreasing temperature through the ductile–brittle transition after plutonic intrusion (Stage I); relatively rapid uplifting (ca. a few mm/year) accompanied by hydrothermal water circulation, which produced uncrushed layered mineral fillings (Stage II); and a period of low‐temperature meteoric water circulation following exposure after uplift (Stage III). The parageneses of carbonate mineral fracture fillings and their carbon isotopic compositions (¹⁴C, δ¹³C) show that there were distinct episodes of carbonate mineral precipitation during the rapid uplifting of a pluton. The carbonate minerals that formed during each episode incorporated carbon from a distinct source. The evolution of fillings identified here enables development of a specific model of fracturing and persistence of fluid‐conducting systems in the plutons of the orogenic field.     

A new apparatus for measuring elastic wave velocity and electrical conductivity of fluid‐saturated rocks at various confining and pore‐fluid pressures

Pore‐fluid pressure is a critical parameter that governs geodynamic processes including seismic activities. Its evaluation through geophysical observations provides us insights into these processes. The quantitative evaluation requires a thorough understanding of the influence of pore‐fluid pressure on geophysical parameters, such as seismic velocity and electrical conductivity. To study the influence of pore‐fluid pressure on these parameters, we have built a new apparatus with a pore‐fluid pressure control system, which is capable of simultaneously measuring elastic wave velocity and electrical conductivity. Our new apparatus employs two sets of plastic piston–cylinders for the electrical insulation and pore‐fluid pressure transmission. The pore fluid is electrically isolated from the metal work, and its pressure can be precisely controlled without significant contribution of the friction between the piston and cylinder. Our new apparatus was used for a simultaneous measurement of velocity and conductivity in a brine‐saturated Berea sandstone. Elastic wave velocity and electrical conductivity changed in response to the change in confining and pore‐fluid pressures, showing the usefulness of the new apparatus.     

Mechanisms of fluid flow and fluid–rock interaction in fossil metamorphic hydrothermal systems inferred from vein–wallrock patterns, geometry and microstructure

Comparison of mass transfer patterns, geometry and microstructures developed within and around veins allows the interpretation of processes of fluid flow during deformation, metamorphism and mineralization. A classification of vein types based on the degree of interaction with wallrock (using petrological, geochemical or isotopic indicators) can be used to identify a range of processes, from closed system behaviour in which the vein mass is derived from local wallrock, through to open system behaviour in which the vein mass is derived externally. Microstructural characteristics, such as wallrock selvages, multiple growth events recorded by vein seams and vein crystal morphology, also help to constrain mass transfer patterns during vein formation. We present a range of processes for vein formation, including: (i) the formation of closed system fibrous veins by dissolution–precipitation creep, including varieties in which tensile failure is not required; (ii) pressure‐ or kinetically dependent closed system segregation veins in which transfer of soluble components from wallrock to vein leaves behind a residual selvage; (iii) similar vein–selvage patterning, but with mass imbalances between vein and wallrock requiring fluid advection through both interconnected fracture networks and in the surrounding permeable rock; and (iv) the proposed formation of veins by fluid ascent in mobile hydrofractures, in which isotopic or chemical disequilibrium within and around the vein suggests that the crack and fluid within it moved essentially as one. The postulate of rapid fluid and mass transfer via such mobile hydrofractures has implications for the release of volatiles from metamorphic terrains. Also, consideration of a broad range of possible vein‐forming mechanisms is highly desirable when dealing with mineral deposits found in deformed, metamorphosed rocks, because closed system veining may produce patterns that, if erroneously recognized as being open systems, could lead to false interpretations of the role of tectonic fracturing in ore genesis.     

An investigation of historical and archaeological evidence for age‐related bone loss and osteoporosis

A growing awareness of the problems caused by osteoporosis‐related fractures has led to increased investigation of the condition in past populations. The present study seeks to examine the ways in which osteoporosis‐related fractures may be explored through different approaches; modern clinical information, historical records of fractures and analysis of archaeological bone may provide fuller information on the condition. The three types of fractures upon which this study focuses are fractures of the femoral neck, Colles' fractures and vertebral compression fractures. The results of the investigation clearly demonstrate the way in which the various sources produce a slightly different picture of the condition. The archaeological significance of the different types of fractures was found to be the reverse of that which would be suspected in the light of information derived from historical sources and the clinical literature. To date vertebral crush fractures have been the most commonly found osteoporosis‐related fracture in archaeological material, but their significance to people in the past is likely to have been minimal. In contrast hip fractures have rarely been reported from archaeological bone material, but historical information makes it clear they were well known, and knowledge derived from clinical sources emphasizes the serious consequences of such a fracture for the affected individuals. The results indicate the value of undertaking a multi‐disciplinary approach where possible. Copyright © 2002 John Wiley & Sons, Ltd.     

Diagenesis of the Amposta offshore oil reservoir (Amposta Marino C2 well,Lower Cretaceous,Valencia Trough,Spain)

Samples from the Amposta Marino C2 well (Amposta oil field) have been investigated in order to understand the origin of fractures and porosity and to reconstruct the fluid flow history of the basin prior, during and after oil migration. Three main types of fracture systems and four types of calcite cements have been identified. Fracture types A and B are totally filled by calcite cement 1 (CC1) and 2 (CC2), respectively; fracture type A corresponds to pre‐Alpine structures, while type B is attributed to fractures developed during the Alpine compression (late Eocene‐early Oligocene). The oxygen, carbon and strontium isotope compositions of CC2 are close to those of the host‐rock, suggesting a high degree of fluid‐rock interaction, and therefore a relatively closed palaeohydrogeological system. Fracture type C, developed during the Neogene extension and enlarged by subaerial exposure, tend to be filled with reddish (CS3r) and greenish (CS3g) microspar calcite sediment and blocky calcite cement type 4 (CC4), and postdated by kaolinite, pyrite, barite and oil. The CS3 generation records lower oxygen and carbon isotopic compositions and higher ⁸⁷Sr/⁸⁶Sr ratios than the host‐limestones. These CS3 karstic infillings recrystallized early within evolved‐meteoric waters having very little interaction with the host‐rock. Blocky calcite cement type 4 (CC4 generation) has the lowest oxygen isotope ratio and the most radiogenic ⁸⁷Sr/⁸⁶Sr values, indicating low fluid‐rock interaction. The increasingly open palaeohydrogeological system was dominated by migration of hot brines with elevated oxygen isotope ratios into the buried karstic system. The main oil emplacement in the Amposta reservoir occurred after the CC4 event, closely related to the Neogene extensional fractures. Corrosion of CC4 (blocky calcite cement type 4) occurred prior to (or during) petroleum charge, possibly related to kaolinite precipitation from relatively acidic fluids. Barite and pyrite precipitation occurred after this corrosion. The sulphur source associated with the late precipitation of pyrite was likely related to isotopically light sulphur expelled, e.g. as sulphide, from the petroleum source rock (Ascla Fm). Geofluids (2010) 10 , 314–333     

Migration of Mn-rich fluids through normal faults and fine-grained terrigenous sediments during early development of the Neogene Vallès-Penedès half-graben (NE Spain)

The Miocene siliciclastic sediments infilling the Vallès‐Penedès half‐graben are affected by two sets of structures developed during the extensional tectonics that created the basin. The first set, represented by extension fractures infilled with mud and sands, is attributed to seismically induced liquefaction. The second set, represented by normal faults, corresponds to a high‐permeability horsetail extensional fracture mesh developed near the surface in the hanging walls of normal faults. The incremental character of the vein‐fills indicates episodic changes in the tectonic stress state and fault zone permeability. Two episodes of fluid migration are recorded. The first episode occurred prior to consolidation and lithification when shallow burial conditions allowed oxidizing meteoric waters to flow horizontally through the more porous and permeable sandy layers. Development of clastic dikes allowed local upward flow and dewatering of the sandy beds. Liquefaction and expulsion of fluids were probably driven by seismic shaking. During the first episode of fluid migration there was no cementation of the sandstone or within the fractures, probably because little fluid was mobilized by the predominantly compaction‐driven flow regime. The second episode of fluid migration occurred synchronously with normal fault development, during which time the faults acted as fluid conduits. Fluids enriched in manganese, probably leached from local manganese oxyhydroxides soon after sedimentation, moved laterally and produced cementation in the sandstone layers, eventually arriving at the more porous and permeable fault pathways that connected compartments of different porosities and permeabilities. Carbonate probably precipitated in fractures saturated with meteoric water near the ground surface at a transitional redox potential. Once the faults became occluded by calcite cement, shortly after fault development, they became barriers to both vertical and horizontal fluid flow.