Physical properties of carbonate fault rocks,fucino basin (Central Italy): implications for fault seal in platform carbonates

We documented the porosity, permeability, pore geometry, pore type, textural anisotropy, and capillary pressure of carbonate rock samples collected along basin‐bounding normal faults in central Italy. The study samples consist of one Mesozoic platform carbonate host rock with low porosity and permeability, four fractured host rocks of the damage zones, and four fault rocks of the fault cores. The four fractured samples have high secondary porosity, due to elongated, connected, soft pores that provide fluid pathways in the damage zone. We modeled this zone as an elastic cracked medium, and used the Budiansky–O'Connell correlation to compute its permeability from the measured elastic moduli. This correlation can be applied only to fractured rocks with large secondary porosity and high‐aspect ratio pores. The four fault rock samples are made up of survivor clasts embedded in fine carbonate matrices and cements with sub‐spherical, stiff pores. The low porosity and permeability of these rocks, and their high values of capillary pressure, are consistent with the fault core sealing as much as 77 and 140 m of gas and oil columns, respectively. We modeled the fault core as a granular medium, and used the Kozeny–Carmen correlation, assigning the value of 5 to the Kozeny constant, to compute its permeability from the measured porosities and pore radii. The permeability structure of the normal faults is composed of two main units with unique hydraulic characteristics: a granular fault core that acts as a seal to cross‐fault fluid flow, and an elastic cracked damage zone that surrounds the core and forms a conduit for fluid flow. Transient pathways for along‐fault fluid flow may form in the fault core during seismic faulting due to the formation of opening‐mode fractures within the cemented fault rocks.     

Factors affecting fluid flow in strike–slip fault systems: coupled deformation and fluid flow modelling with application to the western Mount Isa Inlier, Australia

Deformation and focused fluid flow within a mineralized system are critical in the genesis of hydrothermal ore deposits. Dilation and integrated fluid flux due to coupled deformation and fluid flow in simple strike–slip fault geometries were examined using finite difference analysis in three dimensions. A series of generic fault bend and fault jog geometries consistent with those seen in the western Mount Isa Inlier were modelled in order to understand how fault geometry parameters influence the dilation and integrated fluid flux. Fault dip, fault width, bend/jog angle, and length were varied, and a cross-cutting fault and contrasting rock types were included. The results demonstrate that low fault dips, the presence of contrasts in rock type, and wide faults produce highest dilation and integrated fluid flux values. Increasing fault bend lengths and angles increases dilation and integrated fluid flux, but increasing fault jog length or angle has the opposite effect. There is minimal difference between the outputs from the releasing and restraining fault bend and jog geometries. Model characteristics producing greater fluid flows and/or gradients can be used in a predictive capacity in order to focus exploration on regions with more favorable fault geometries, provided that the mineralized rocks had Mohr–Coulomb rheologies similar to the ones used in the models.     

Communication between overpressured compartments

Overpressure build‐up in compartments, and communication between overpressured compartments across faults are studied with simple analytical and numerical models. It is shown that the excess pressure in a (vertical) one‐dimensional, one‐compartment model can be written as the sum of the excess pressure generated in the seal above the compartment, and a second part, which is due to the expulsion of fluid from the compartment and the rocks below. The one‐compartment model is generalized to a two‐compartment model, which accounts for the fluid communication between the compartments through a fault zone. The volume rates of flow through the seals and the fault zone are shown to be the weighted mean of the volume rates of the one‐dimensional, one‐compartment model. The normalized weights are given by dimensionless numbers, called fault–seal numbers, which control the communication between the compartments. A fault–seal number much less than unity implies that the fault is a stronger barrier for the fluid flow than the seal. A fault–seal number larger than unity implies the opposite: that the seal is a stronger barrier than the fault. The conditions for isolated compartments and other regimes are identified in terms of the fault–seal numbers. It is discussed how the compartment fault–seal numbers can be computed when the permeability is given in the fault zone. The results given by the analytical compartment models are demonstrated and validated with two‐dimensional numerical (finite element) simulations.     

Effects of episodic fluid flow on hydrocarbon migration in the Newport‐Inglewood Fault Zone,Southern California

Fault permeability may vary through time due to tectonic deformations, transients in pore pressure and effective stress, and mineralization associated with water‐rock reactions. Time‐varying permeability will affect subsurface fluid migration rates and patterns of petroleum accumulation in densely faulted sedimentary basins such as those associated with the borderland basins of Southern California. This study explores the petroleum fluid dynamics of this migration. As a multiphase flow and petroleum migration case study on the role of faults, computational models for both episodic and continuous hydrocarbon migration are constructed to investigate large‐scale fluid flow and petroleum accumulation along a northern section of the Newport‐Inglewood fault zone in the Los Angeles basin, Southern California. The numerical code solves the governing equations for oil, water, and heat transport in heterogeneous and anisotropic geologic cross sections but neglects flow in the third dimension for practical applications. Our numerical results suggest that fault permeability and fluid pressure fluctuations are crucial factors for distributing hydrocarbon accumulations associated with fault zones, and they also play important roles in controlling the geologic timing for reservoir filling. Episodic flow appears to enhance hydrocarbon accumulation more strongly by enabling stepwise build‐up in oil saturation in adjacent sedimentary formations due to temporally high pore pressure and high permeability caused by periodic fault rupture. Under assumptions that fault permeability fluctuate within the range of 1–1000 millidarcys (10^?15–10^?12 m²) and fault pressures fluctuate within 10–80% of overpressure ratio, the estimated oil volume in the Inglewood oil field (approximately 450 million barrels oil equivalent) can be accumulated in about 24 000 years, assuming a seismically induced fluid flow event occurs every 2000 years. This episodic petroleum migration model could be more geologically important than a continuous‐flow model, when considering the observed patterns of hydrocarbons and seismically active tectonic setting of the Los Angeles basin.     

An exhumed palaeo-hydrocarbon migration fairway in a faulted carrier system, Entrada Sandstone of SE Utah, USA

The Moab Anticline, east‐central Utah, is an exhumed hydrocarbon palaeo‐reservoir which was supplied by hydrocarbons that migrated from the Moab Fault up‐dip towards the crest of the structure beneath the regional seal of the Tidwell mudstone. Iron oxide reduction in porous, high permeability aeolian sandstones records the secondary migration of hydrocarbons, filling of traps against small sealing faults and spill pathways through the Middle Jurassic Entrada Sandstone. Hydrocarbons entered the Entrada Sandstone carrier system from bends and other leak points on the Moab Fault producing discrete zones of reduction that extend for up to 400 m from these leak points. They then migrated in focused stringers, 2–5 m in height, to produce accumulations on the crest of the anticline. Normal faults on the anticline were transient permeability barriers to hydrocarbon migration producing a series of small compartmentalized accumulations. Exsolution of CO₂ as local fault seals were breached resulted in calcite cementation on the up‐dip side of faults. Field observations on the distribution of iron oxide reduction and calcite cements within the anticline indicate that the advancing reduction fronts were affected neither by individual slip bands in damage zones around faults nor by small faults with sand: sand juxtapositions. Faults with larger throws produced either sand: mudstone juxtapositions or sand: sand contacts and fault zones with shale smears. Shale‐smeared fault zones provided seals to the reducing fluid which filled the structural traps to spill points.     

Linked thermal convection of the basement and basinal fluids in formation of the unconformity‐related uranium deposits in the Athabasca Basin,Saskatchewan, Canada

World‐class unconformity‐related U deposits in the Athabasca Basin (Saskatchewan, Canada) are generally located within or near fault zones that intersect the unconformity between the Athabasca Group sedimentary basin rocks and underlying metamorphic basement rocks. Two distinct subtypes of unconformity‐related uranium deposits have been identified: those hosted primarily in the Athabasca Group sandstones (sediment‐hosted) and those hosted primarily in the underlying basement rocks (basement‐hosted). Although significant research on these deposits has been carried out, certain aspects of their formation are still under discussion, one of the main issues being the fluid flow mechanisms responsible for uranium mineralization. The intriguing feature of this problem is that sediment‐hosted and basement‐hosted deposits are characterized by oppositely directed vectors of fluid flow via associated fault zones. Sediment‐hosted deposits formed via upward flow of basement fluids, basement‐hosted deposits via downward flow of basinal fluids. We have hypothesized that such flow patterns are indicative of the fluid flow self‐organization in fault‐bounded thermal convection (Transport in Porous Media, 110, 2015, 25). To explore this hypothesis, we constructed a simplified hydrogeologic model with fault‐bounded thermal convection of fluids in the faulted basement linked with fluid circulation in the overlying fault‐free sandstone horizon. Based on this model, a series of numerical experiments was carried out to simulate the hypothesized fluid flow patterns. The results obtained are in reasonable agreement with the concept of fault‐bounded convection cells as an explanation of focused upflow and downflow across the basement/sandstone unconformity. We then discuss application of the model to another debated problem, the uranium source for the ore‐forming basinal brines.     

Carbon dioxide controlled earthquake distribution pattern in the NW Bohemian swarm earthquake region,western Eger Rift,Czech Republic – gas migration in the crystalline basement

The ascent of magmatic carbon dioxide in the western Eger (Oh?e) Rift is interlinked with the fault systems of the Variscian basement. In the Cheb Basin, the minimum CO₂ flux is about 160 m³ h^?1, with a diminishing trend towards the north and ceasing in the main epicentral area of the Northwest Bohemian swarm earthquakes. The ascending CO₂ forms Ca‐Mg‐HCO₃ type waters by leaching of cations from the fault planes and creates clay minerals, such as kaolinite, as alteration products on affected fault planes. These mineral reactions result in fault weakness and in hydraulically interconnected fault network. This leads to a decrease in the friction coefficient of the Coulomb failure stress (CFS) and to fault creep as stress build‐up cannot occur in the weak segments. At the transition zone in the north of the Cheb Basin, between areas of weak, fluid conductive faults and areas of locked faults with frictional strength, fluid pressure can increase resulting in stress build‐up. This can trigger strike‐slip swarm earthquakes. Fault creep or movements in weak segments may support a stress build‐up in the transition area by transmitting fluid pressure pulses. Additionally to fluid‐driven triggering models, it is important to consider that fluids ascending along faults are CO₂‐supersaturated thus intensifying the effect of fluid flow. The enforced flow of CO₂‐supersaturated fluids in the transitional zone from high to low permeability segments through narrowings triggers gas exsolution and may generate pressure fluctuations. Phase separation starts according to the phase behaviour of CO₂‐H₂O systems in the seismically active depths of NW Bohemia and may explain the vertical distribution of the seismicity. Changes in the size of the fluid transport channels in the fault systems caused, or superimposed, by fault movements, can produce fluid pressure increases or pulses, which are the precondition for triggering fluid‐induced swarm earthquakes.     

The application of failure mode diagrams for exploring the roles of fluid pressure and stress states in controlling styles of fracture-controlled permeability enhancement in faults and shear zones

Permeability enhancement associated with deformation processes in faults and shear zones plays a key role in facilitating fluid redistribution between fluid reservoirs in the crust. Especially in high fluid flux hydrothermal systems, fracture-controlled permeability can be relatively short-lived, unless it is repeatedly regenerated by ongoing deformation. Failure mode diagrams in pore fluid factor and differential stress space, here termed λ–σ failure mode diagrams, provide a powerful tool for analysing how fluid pressure and stress states drive failure, associated permeability enhancement and vein styles during deformation in faults and shear zones. During fault-valve behaviour in the seismogenic regime, relative rates of recovery of pore fluid factor, differential stress and fault cohesive strength between rupture events impact on styles of veining and associated, fracture-controlled permeability enhancement in faults and shear zones. Examples of vein-rich fault zones are used to illustrate how constraints can be placed, not just on fluid pressure and stress states at failure, but also on the fluid pressurization and loading paths associated with failure and transitory permeability enhancement in faults and shear zones. This provides insights about when, during the fault-valve cycle, various types of veins can form. The use of failure mode diagrams also provides insights about the relative roles of optimally oriented faults and misoriented faults as hydraulically conductive structures. The analysis highlights the dynamics of competition between fluid pressures and loading rates in driving failure and repeated permeability regeneration in fracture-controlled, hydrothermal systems.     

Structural controls on hydrothermal flow in a segmented rift system, Taupo Volcanic Zone, New Zealand

Vigorous hydrothermal convection transfers 10 times the average continental heat flow through the central Taupo Volcanic Zone (TVZ), a region of active extension (approximately 8 mm year^?1) and productive rhyolitic volcanism. Over 20 high‐temperature (>250°C) geothermal fields occur within Quaternary pyroclastic basins, with convective circulation to depths of 7–8 km presumably extending through basement rocks. Parallel‐striking normal faults, fractures and dikes dissect the convective regime, interacting with fluids to either enhance or restrict flow according to the relative permeability of structure and host rock. In the basement, high bulk permeability is maintained by focussed flow through faults and associated fractures well oriented for reactivation in the prevailing stress field. In contrast, distributed flow through fault‐bounded compartments prevails within Quaternary basins, masking any signal of deeper structural control. Exceptions occur where more competent rocks are exposed at the surface. As in narrow magmatic rifts elsewhere, the extensional fabric is partitioned into discrete rift segments linked along strike by accommodation zones. Eighty per cent of TVZ geothermal fields correlate spatially with rift architecture, with 60% located in accommodation zones. We suggest that segmented rift fabrics generate bulk permeability anisotropy that is to some extent predictable, with rift segments characterized by enhanced axial flow, and accommodation zones characterized by locally enhanced vertical permeability that is tectonically maintained. This provides a plausible explanation for the common occurrence of geothermal fields within accommodation zones and their notable absence within densely faulted rift segments. Maintenance of structural permeability in zones of active hydrothermal precipitation necessarily requires repeated brittle failure. Geothermal plumes therefore exploit tectonically maintained permeability within accommodation zones, with rift segments functioning mostly as drawdown regions. The influence of rift architecture on flow paths has important implications for geothermal extraction and epithermal mineral exploration within the TVZ and other structurally segmented hydrothermal systems, both active and extinct.     

Timescales for reaching steady-state fluid flow in systems perturbed by formation of highly permeable faults

We consider the case of an isothermal, fluid‐saturated, homogeneous rock layer with transverse fluid flow driven by an imposed constant fluid pressure gradient. A rupture in the centre of the rock layer generates a highly permeable fault and results in a change of the initially homogeneous permeability distribution. This leads to a perturbation of the fluid flow field and its gradual transition to a new steady‐state corresponding to the new permeability distribution. An examination of this transitional process permits us to obtain an analytical estimation of the transition stage duration. The application of the results obtained to km‐scale faults in crystalline rock bodies leads to the conclusion that the evolution of the fluid velocity field is rather rapid compared with geological timescales.     

Evolution of deformation and fault‐related fluid flow within an ancient methane seep system (Eocene,Varna, Bulgaria)

Faults are often important in fuelling methane seep systems; however, little is known on how different components in fault zones control subsurface fluid circulation paths and how they evolve through time. This study provides insight into fault‐related fluid flow systems that operated in the shallow subsurface of an ancient methane seep system. The Pobiti Kamani area (NE Bulgaria) encloses a well‐exposed, fault‐related seep system in unconsolidated Lower Eocene sandy deposits of the Dikilitash Formation. The Beloslav quarry and Beloslav N faults displace the Dikilitash Formation and are typified by broad, up to 80 m wide, preferentially lithified hanging wall damage zones, crosscut by deformation bands and deformation band zones, smaller slip planes and fault‐related joints. The formation of a shallow plumbing system and chimney‐like concretions in the Dikilitash Formation was followed by at least two phases of fault‐related methane fluid migration. Widespread fluid circulation through the Dikilitash sands caused massive cementation of the entire damage zones in the fault hanging walls. During this phase, paths of ascending methane fluids were locally obstructed by decimetre‐thick, continuous deformation band zones that developed in the partly lithified sands upon the onset of deformation. Once the entire damage zone was pervasively cemented, deformation proceeded through the formation of slip planes and joints. This created a new network of more localized conduits in close vicinity to the main fault plane and around through‐going slip planes. ¹³C‐depleted crustiform calcite cements in several joints record the last phase of focused methane fluid ascent. Their formation predated Neogene uplift and later meteoric water infiltration along the joint network. This illustrates how fault‐related fluid pathways evolved, over time, from ‘plumes’ in unconsolidated sediments above damage zones, leading to chimney fields, over widespread fluid paths, deflected by early deformation structures, to localized paths along fracture networks near the main fault.     

Modeling fluid flow in a heterogeneous, fault-controlled hydrothermal system

Previous studies have shown that most hydrothermal systems discharging at the land surface are associated with faulting, and that the location, temperature and rate of discharge of these systems are controlled by the geometry and style of the controlling fault(s). Unfortunately, the transport of heat and fluid in fault-controlled hydrothermal systems is difficult to model realistically; although heterogeneity and anisotropy are assumed to place important controls on flow in faults, few data or observations are available to constrain the distribution of hydraulic properties within active faults. Here, analytical and numerical models are combined with geostatistical models of spatially varying hydraulic properties to model the flow of heat and fluid in the Borax Lake fault of south-east Oregon, USA. A geometric mean permeability within the fault of 7 × 10⁻¹⁴ m² with 2× vertical/horizontal anisotropy in correlation length scale is shown to give the closest match to field observations. Furthermore, the simulations demonstrate that continuity of flow paths is an important factor in reproducing the observed behavior. In addition to providing some insight into possible spatial distributions of hydraulic properties at the Borax Lake site, the study highlights one potential avenue for integrating field observations with simulation results in order to gain greater understanding of fluid flow in faults and fault-controlled hydrothermal and petroleum reservoirs.     

Capillary seal capacity of faults under hydrodynamic conditions

Many fault bound traps are underfilled despite the top seal capacity being secure. The hydrocarbon sealing performance of faults themselves can be compromised either by mechanical or capillary process. Capillary process can be important either due to juxtaposition or to fine‐grained clay or cataclastic material within the fault zone itself. There is debate about how important each of these mechanisms is over geological timescales of hydrocarbon trapping. Recent work has provided insights into fine‐tuning capillary‐related fault seal calibration methodologies. Over the last 15 years, vigorous scientific debate with multiple published laboratory experiments and modelling studies has led some researchers and industry technologists to theorise that for water‐wet conventional hydrocarbon reservoirs, the relative water permeability in the reservoir (towards the top of the hydrocarbon column) may become very small, but in practice never reach zero. While not advocating for either side in this debate, the importance of accounting for hydrodynamic conditions regardless of the capillary sealing mechanism is demonstrated. Additionally, it is noted that nonzero relative water permeability has implications on how a seal's capillary threshold pressure for the nonwetting hydrocarbon phase is estimated from field data. In the particular case where there are pressure differences between unproduced hydrocarbon reservoirs on either side of a fault, then the hydrocarbon saturation must be discontinuous across the fault. For hydrocarbon leakage to occur across the entire thickness of the fault zone, the hydrocarbon pressure must exceed the threshold pressure on the side of the fault zone with the highest formation water hydraulic head. This approach to estimating across‐fault pressure difference will result in an improved calibration data set used for predrill estimation of capillary fault seal capacity.     

Faults and fault properties in hydrocarbon flow models

The petroleum industry uses subsurface flow models for two principal purposes: to model the flow of hydrocarbons into traps over geological time, and to simulate the production of hydrocarbon from reservoirs over periods of decades or less. Faults, which are three-dimensional volumes, are approximated in both modelling applications as planar membranes onto which predictions of the most important fault-related flow properties are mapped. Faults in porous clastic reservoirs are generally baffles or barriers to flow and the relevant flow properties are therefore very different to those which are important in conductive fracture flow systems. A critical review and discussion is offered on the work-flows used to predict and model capillary threshold pressure for exploration fault seal analysis and fault transmissibility multipliers for production simulation, and of the data from which the predictions derive. New flow simulation models confirm that failure of intra-reservoir sealing faults can occur during a reservoir depressurization via a water-drive mechanism, but contrary to anecdotal reports, published examples of production-induced seal failure are elusive. Ignoring the three-dimensional structure of fault zones can sometimes have a significant influence on production-related flow, and a series of models illustrating flow associated with relay zones are discussed.     

Polyphasic hydrothermal and meteoric fluid regimes during the growth of a segmented fault involving crystalline and carbonate rocks (Barcelona Plain,NE Spain)

A polyphasic tectonic‐fluid system of a fault that involves crystalline and carbonate rocks (Hospital fault, Barcelona Plain) has been inferred from regional to thin section scale observations combined with geochemical analyses. Cathodoluminescence, microprobe analyses and stable isotopy in fracture‐related cements record the circulation of successive alternations of hydrothermal and low‐temperature meteoric fluids linked with three main regional tectonic events. The first event corresponds to the Mesozoic extension, which had two rifting stages, and it is characterized by the independent tectonic activity of two fault segments, namely southern and northern Hospital fault segments. During the Late Permian‐Middle Jurassic rifting, these segments controlled the thickness and distribution of the Triassic sediments. Also, dolomitization was produced in an early stage by Triassic seawater at shallow conditions. During increasing burial, formation of fractures and their dolomite‐related cements took place. Fault activity during the Middle Jurassic–Late Cretaceous rifting was localized in the southern segment, and it was characterized by hydrothermal brines, with temperatures over 180°C, which ascended through this fault segment precipitating quartz, chlorite, and calcite. The second event corresponds to the Paleogene compression (Chattian), which produced exhumation, folding and erosion, favouring the percolation of low‐temperature meteoric fluids which produced the calcitization of the dolostones and of the dolomite cements. The third event is linked with the Neogene extension, where three stages have been identified. During the syn‐rift stage, the southern segment of the Hospital fault grew by tip propagation. In the relay zone, hydrothermal brines with temperature around 140°C upflowed. During the late postrift, the Hospital fault acted as a unique segment and deformation occurred at shallow conditions and under a low‐temperature meteoric regime. Finally, and possibly during the Messinian compression, NW‐SE strike‐slip faults offset the Hospital fault to its current configuration.     

Transient fluid flow in and around a fault

We present the results of simple numerical experiments in which we study the evolution with time of fluid flow around and within a permeable fault embedded in a less permeable porous medium. Fluid movement is driven by an imposed vertical pressure gradient. The results show that fluid flow is controlled by two timescales: τ_f = Sl²/κ_F and τ_F = Sl²/κ_M, where S is the specific storage of the porous material, l the length of the fault, and κ_M and κ_F are the hydraulic conductivities of the porous material and the fault, respectively. Fluid flow and the associated fluid pressure field evolve through three temporal stages: an early phase [t < τ_f] during which the initial fluid pressure gradient within the fault is relaxed; a second transient stage [τ_f < t < τ_F] when fluid is rapidly expelled at one end of the fault and extracted from the surrounding rocks at the other end leading to a reduction in the pressure gradient in the intact rock; a third phase [t < τ_F] characterized by a steady‐state flow. From the numerical experiments we derive an expression for the steady‐state maximum fluid velocity in the fault and the values of the two timescales, τ_f and τ_F. A comparison indicates excellent agreement of our results with existing asymptotic solutions. For km‐scale faults, the model results suggest that steady‐state is unlikely to be reached over geological timescales. Thus, the current use of parameters such as the focusing ratio defined under the assumption of steady‐state conditions should be reconsidered.     

The upper continental crust, an aquifer and its fluid: hydaulic and chemical data from 4 km depth in fractured crystalline basement rocks at the KTB test site

Detailed information on the hydrogeologic and hydraulic properties of the deeper parts of the upper continental crust is scarce. The pilot hole of the deep research drillhole (KTB) in crystalline basement of central Germany provided access to the crust for an exceptional pumping experiment of 1‐year duration. The hydraulic properties of fractured crystalline rocks at 4 km depth were derived from the well test and a total of 23100 m³ of saline fluid was pumped from the crustal reservoir. The experiment shows that the water‐saturated fracture pore space of the brittle upper crust is highly connected, hence, the continental upper crust is an aquifer. The pressure–time data from the well tests showed three distinct flow periods: the first period relates to wellbore storage and skin effects, the second flow period shows the typical characteristics of the homogeneous isotropic basement rock aquifer and the third flow period relates to the influence of a distant hydraulic border, probably an effect of the Franconian lineament, a steep dipping major thrust fault known from surface geology. The data analysis provided a transmissivity of the pumped aquifer T = 6.1 × 10^?6 m² sec^?1, the corresponding hydraulic conductivity (permeability) is K = 4.07 × 10^?8 m sec^?1 and the computed storage coefficient (storativity) of the aquifer of about S = 5 × 10^?6. This unexpected high permeability of the continental upper crust is well within the conditions of possible advective flow. The average flow porosity of the fractured basement aquifer is 0.6–0.7% and this range can be taken as a representative and characteristic values for the continental upper crust in general. The chemical composition of the pumped fluid was nearly constant during the 1‐year test. The total of dissolved solids amounts to 62 g l^?1 and comprise mainly a mixture of CaCl₂ and NaCl; all other dissolved components amount to about 2 g l^?1. The cation proportions of the fluid (X_Ca approximately 0.6) reflects the mineralogical composition of the reservoir rock and the high salinity results from desiccation (H₂O‐loss) due to the formation of abundant hydrate minerals during water–rock interaction. The constant fluid composition suggests that the fluid has been pumped from a rather homogeneous reservoir lithology dominated by metagabbros and amphibolites containing abundant Ca‐rich plagioclase.     

Gas breakthrough experiments on pelitic rocks: comparative study with N2, CO2 and CH4

The capillary‐sealing efficiency of intermediate‐ to low‐permeable sedimentary rocks has been investigated by N₂, CO₂ and CH₄ breakthrough experiments on initially fully water‐saturated rocks of different lithological compositions. Differential gas pressures up to 20 MPa were imposed across samples of 10–20 mm thickness, and the decline of the differential pressures was monitored over time. Absolute (single‐phase) permeability coefficients (k_abs), determined by steady‐state fluid flow tests, ranged between 10^?22 and 10^?15 m². Maximum effective permeabilities to the gas phase k_eff(max), measured after gas breakthrough at maximum gas saturation, extended from 10^?26 to 10^?18 m². Because of re‐imbibition of water into the interconnected gas‐conducting pore system, the effective permeability to the gas phase decreases with decreasing differential (capillary) pressure. At the end of the breakthrough experiments, a residual pressure difference persists, indicating the shut‐off of the gas‐conducting pore system. These pressures, referred to as the ‘minimum capillary displacement pressures’ (P_d), ranged from 0.1 up to 6.7 MPa. Correlations were established between (i) absolute and effective permeability coefficients and (ii) effective or absolute permeability and capillary displacement pressure. Results indicate systematic differences in gas breakthrough behaviour of N₂, CO₂ and CH₄, reflecting differences in wettability and interfacial tension. Additionally, a simple dynamic model for gas leakage through a capillary seal is presented, taking into account the variation of effective permeability as a function of buoyancy pressure exerted by a gas column underneath the seal.     

Migration of Mn-rich fluids through normal faults and fine-grained terrigenous sediments during early development of the Neogene Vallès-Penedès half-graben (NE Spain)

The Miocene siliciclastic sediments infilling the Vallès‐Penedès half‐graben are affected by two sets of structures developed during the extensional tectonics that created the basin. The first set, represented by extension fractures infilled with mud and sands, is attributed to seismically induced liquefaction. The second set, represented by normal faults, corresponds to a high‐permeability horsetail extensional fracture mesh developed near the surface in the hanging walls of normal faults. The incremental character of the vein‐fills indicates episodic changes in the tectonic stress state and fault zone permeability. Two episodes of fluid migration are recorded. The first episode occurred prior to consolidation and lithification when shallow burial conditions allowed oxidizing meteoric waters to flow horizontally through the more porous and permeable sandy layers. Development of clastic dikes allowed local upward flow and dewatering of the sandy beds. Liquefaction and expulsion of fluids were probably driven by seismic shaking. During the first episode of fluid migration there was no cementation of the sandstone or within the fractures, probably because little fluid was mobilized by the predominantly compaction‐driven flow regime. The second episode of fluid migration occurred synchronously with normal fault development, during which time the faults acted as fluid conduits. Fluids enriched in manganese, probably leached from local manganese oxyhydroxides soon after sedimentation, moved laterally and produced cementation in the sandstone layers, eventually arriving at the more porous and permeable fault pathways that connected compartments of different porosities and permeabilities. Carbonate probably precipitated in fractures saturated with meteoric water near the ground surface at a transitional redox potential. Once the faults became occluded by calcite cement, shortly after fault development, they became barriers to both vertical and horizontal fluid flow.     

Hydrothermal control on organic matter alteration and illite precipitation, Mt Isa Basin, Australia

Abundant illite precipitation in Proterozoic rocks from Northern Lawn Hill Platform, Mt Isa Basin, Australia, occurred in organic matter‐rich black shales rather than in sandstones, siltstones and organic matter‐poor shales. Sandstones and siltstones acted as impermeable rocks, as early diagenetic quartz and carbonate minerals reduced the porosity–permeability. Scanning and transmission electron microscopy (SEM and TEM) studies indicate a relation between creation of microporosity–permeability and organic matter alteration, suitable for subsequent mineral precipitation. K–Ar data indicate that organic matter alteration and the subsequent illite precipitation within the organic matter occurred during the regional hydrothermal event at 1172 ± 50 (2σ) Ma. Hot circulating fluids are considered to be responsible for organic matter alteration, migration and removal of volatile hydrocarbon, and consequently porosity–permeability creation. Those rocks lacking sufficient porosity–permeability, such as sandstones, siltstones and organic matter poor shales, may not have been affected by fluid movement. In hydrothermal systems, shales and mudstones may not be impermeable as usually assumed because of hydrocarbons being rapidly removed by fluid, even with relatively low total organic carbon.