Gas breakthrough experiments on pelitic rocks: comparative study with N2, CO2 and CH4

The capillary‐sealing efficiency of intermediate‐ to low‐permeable sedimentary rocks has been investigated by N₂, CO₂ and CH₄ breakthrough experiments on initially fully water‐saturated rocks of different lithological compositions. Differential gas pressures up to 20 MPa were imposed across samples of 10–20 mm thickness, and the decline of the differential pressures was monitored over time. Absolute (single‐phase) permeability coefficients (k_abs), determined by steady‐state fluid flow tests, ranged between 10^?22 and 10^?15 m². Maximum effective permeabilities to the gas phase k_eff(max), measured after gas breakthrough at maximum gas saturation, extended from 10^?26 to 10^?18 m². Because of re‐imbibition of water into the interconnected gas‐conducting pore system, the effective permeability to the gas phase decreases with decreasing differential (capillary) pressure. At the end of the breakthrough experiments, a residual pressure difference persists, indicating the shut‐off of the gas‐conducting pore system. These pressures, referred to as the ‘minimum capillary displacement pressures’ (P_d), ranged from 0.1 up to 6.7 MPa. Correlations were established between (i) absolute and effective permeability coefficients and (ii) effective or absolute permeability and capillary displacement pressure. Results indicate systematic differences in gas breakthrough behaviour of N₂, CO₂ and CH₄, reflecting differences in wettability and interfacial tension. Additionally, a simple dynamic model for gas leakage through a capillary seal is presented, taking into account the variation of effective permeability as a function of buoyancy pressure exerted by a gas column underneath the seal.     

Quantitative analysis of COH fluids synthesized at HP–HT conditions: an optimized methodology to measure volatiles in experimental capsules

The quantitative assessment of COH fluids is crucial in modeling geological processes. The composition of fluids, and in particular their H₂O/CO₂ ratio, can influence the melting temperatures, the location of hydration or carbonation reactions, and the solute transport capability in several rock systems. In the scientific literature, COH fluids speciation has been generally assumed on the basis of thermodynamic calculations using equations of state of simple H₂O–nonpolar gas systems (e.g., H₂O–CO₂–CH₄). Only few authors dealt with the experimental determination of high‐pressure COH fluid species at different conditions, using diverse experimental and analytical approaches (e.g., piston cylinder + capsule piercing + gas chromatography/mass spectrometry; cold seal + silica glass capsules + Raman). In this contribution, we present a new methodology for the synthesis and the analysis of COH fluids in experimental capsules, which allows the quantitative determination of volatiles in the fluid by means of a capsule‐piercing device connected to a quadrupole mass spectrometer. COH fluids are synthesized starting from oxalic acid dihydrate at P = amb and T = 250°C in single capsules heated in a furnace, and at P = 1 GPa and T = 800°C using a piston‐cylinder apparatus and the double‐capsule technique to control the redox conditions employing the rhenium–rhenium oxide oxygen buffer. A quantitative analysis of H₂O, CO₂, CH₄, CO, H₂, O₂, and N₂ along with associated statistical errors is obtained by linear regression of the m/z data of the sample and of standard gas mixtures of known composition. The estimated uncertainties are typically <1% for H₂O and CO₂, and <5% for CO. Our results suggest that the COH fluid speciation is preserved during and after quench, as the experimental data closely mimic the thermodynamic model both in terms of bulk composition and fluid speciation.     

Br/Cl signature of hydrothermal fluids: liquid–vapour fractionation of bromine revisited

Br/Cl ratios of hydrothermal fluids are widely used as geochemical tracers in marine hydrothermal systems to prove fluid phase separation processes. However, previous results of the liquid–vapour fractionation of bromine are ambiguous. Here we report new experimental results of the liquid–vapour fractionation of bromine in the system H₂O–NaCl–NaBr at 380–450°C and 22.9–41.7 MPa. Our data indicate that bromine is generally more enriched than chlorine in the liquid phase. Calculated exchange coefficients K_D(Br‐Cl)^{liquid‐vapour} for the reaction Br^vapour + Cl^liquid = Br^liquid + Cl^vapour are between 0.94 ± 0.08 and 1.66 ± 0.14 within the investigated P–T range. They correlate positively with D_Cl^{liquid‐vapour} and suggest increasing bromine–chlorine fractionation with increasing opening of the liquid–vapour solvus, i.e. increasing distance to the critical curve in the H₂O–NaCl system. An empirical fit of the form K_D(Br‐Cl)^{liquid‐vapour} = a*ln[b*(D_Cl^{liquid‐vapour}?1) + e^1/a] yields a = 0.349 and b = 1.697. Based on this empirical fit and the well‐constrained phase relations in the H₂O–NaCl system we calculated the effect of fluid phase separation on the Br/Cl signature of a hydrothermal fluid with initial seawater composition for closed and open adiabatic ascents along the 4.5 and 4.8 J g^?1 K^?1 isentropes. The calculations indicate that fluid phase separation can significantly alter the Br/Cl ratio in hydrothermal fluids. The predicted Br/Cl evolutions are in accord with the Br/Cl signatures in low‐salinity vent fluids from the 9 to 10°N East Pacific Rise.     

Monitoring fluid chemistry in iron oxide–copper–gold‐related metasomatic processes,eastern Mt Isa Block,Australia

Most researchers in the Proterozoic eastern Mt Isa Block, NW Queensland, Australia, favour magmatic fluid and salt sources for sodic‐(calcic) alteration and iron oxide–copper–gold mineralization. Here we compare spatial, mineralogic and stable isotope data from regional alteration assemblages with magmatic and magmatic‐hydrothermal interface rocks in order to track chemical and isotopic variations in fluid composition away from inferred fluid sources. Tightly clustered δ¹⁸O values for magnetite, quartz, feldspar and actinolite for igneous‐hosted samples reflect high temperature equilibration in the magmatic‐hydrothermal environment. In contrast, these minerals record predominantly higher δ¹⁸O values in regional alteration and Cu–Au mineralization. This dichotomy reflects partial equilibration with isotopically heavier wallrocks and slightly lower temperatures. Increases in Si concentrations of metasomatic amphiboles relative to igneous amphiboles in part reflect cooling of metasomatic fluids away from igneous rocks. Variations in X_Mg for metasomatic amphiboles indicate local wallrock controls on amphibole chemistry, while variations in X_Cl/X_OH ratios for amphiboles (at constant X_Mg) indicate variable aH₂O/aHCl ratios for metasomatic fluids. Biotite geochemistry also reflects cooling and both increases and decreases in aH₂O/aHCl for fluids away from plutonic rocks. Decreased aH₂O/aHCl ratios for metasomatic fluids reflect in part scavenging of chlorine out of meta‐evaporite sequences, although this process requires already saline fluids. Local increases in aH₂O/aHCl ratios, as well as local decreases in δ¹⁸O values for some minerals (most notably haematite and epithermal‐textured quartz), may indicate ingress of low salinity, low δ¹⁸O fluids of possible meteoric origin late in the hydrothermal history of the region. Taken together, our observations are most consistent with predominantly magmatic sources for metasomatic fluids in the eastern Mt Isa Block, but record chemical and isotopic variations along fluid flow paths that may be important in explaining some of the diversity in alteration and mineralization styles in the district.     

The upper continental crust, an aquifer and its fluid: hydaulic and chemical data from 4 km depth in fractured crystalline basement rocks at the KTB test site

Detailed information on the hydrogeologic and hydraulic properties of the deeper parts of the upper continental crust is scarce. The pilot hole of the deep research drillhole (KTB) in crystalline basement of central Germany provided access to the crust for an exceptional pumping experiment of 1‐year duration. The hydraulic properties of fractured crystalline rocks at 4 km depth were derived from the well test and a total of 23100 m³ of saline fluid was pumped from the crustal reservoir. The experiment shows that the water‐saturated fracture pore space of the brittle upper crust is highly connected, hence, the continental upper crust is an aquifer. The pressure–time data from the well tests showed three distinct flow periods: the first period relates to wellbore storage and skin effects, the second flow period shows the typical characteristics of the homogeneous isotropic basement rock aquifer and the third flow period relates to the influence of a distant hydraulic border, probably an effect of the Franconian lineament, a steep dipping major thrust fault known from surface geology. The data analysis provided a transmissivity of the pumped aquifer T = 6.1 × 10^?6 m² sec^?1, the corresponding hydraulic conductivity (permeability) is K = 4.07 × 10^?8 m sec^?1 and the computed storage coefficient (storativity) of the aquifer of about S = 5 × 10^?6. This unexpected high permeability of the continental upper crust is well within the conditions of possible advective flow. The average flow porosity of the fractured basement aquifer is 0.6–0.7% and this range can be taken as a representative and characteristic values for the continental upper crust in general. The chemical composition of the pumped fluid was nearly constant during the 1‐year test. The total of dissolved solids amounts to 62 g l^?1 and comprise mainly a mixture of CaCl₂ and NaCl; all other dissolved components amount to about 2 g l^?1. The cation proportions of the fluid (X_Ca approximately 0.6) reflects the mineralogical composition of the reservoir rock and the high salinity results from desiccation (H₂O‐loss) due to the formation of abundant hydrate minerals during water–rock interaction. The constant fluid composition suggests that the fluid has been pumped from a rather homogeneous reservoir lithology dominated by metagabbros and amphibolites containing abundant Ca‐rich plagioclase.     

Fluid effect on hydraulic fracture propagation behavior: a comparison between water and supercritical CO2‐like fluid

The initiation of hydraulic fractures during fluid injection in deep formations can be either engineered or induced unintentionally. Upon injection of CO₂, the pore fluids in deep formations can be changed from oil/saline water to CO₂ or CO₂ dominated. The type of fluid is important not only because the fluid must fracture the rock, but also because rocks saturated with different pore fluids behave differently. We investigated the influence of fluid properties on fracture propagation behavior by using the cohesive zone model in conjunction with a poroelasticity model. Simulation results indicate that the pore pressure fields are very different for different pore fluids even when the initial field conditions and injection schemes (rate and time) are kept the same. Low viscosity fluids with properties of supercritical CO₂ will create relatively thin and much shorter fractures in comparison with fluids exhibiting properties of water under similar injection schemes. Two significant times are recognized during fracture propagation: the time at which a crack ceases opening and the later time point at which a crack ceases propagating. These times are very different for different fluids. Both fluid compressibility and viscosity influence fracture propagation, with viscosity being the more important property. Viscosity can greatly affect hydraulic conductivity and the leak‐off coefficient. This analysis assumes the in‐situ pore fluid and injected fluid are the same and the pore space is 100% saturated by that fluid at the beginning of the simulation.     

Carbon dioxide controlled earthquake distribution pattern in the NW Bohemian swarm earthquake region,western Eger Rift,Czech Republic – gas migration in the crystalline basement

The ascent of magmatic carbon dioxide in the western Eger (Oh?e) Rift is interlinked with the fault systems of the Variscian basement. In the Cheb Basin, the minimum CO₂ flux is about 160 m³ h^?1, with a diminishing trend towards the north and ceasing in the main epicentral area of the Northwest Bohemian swarm earthquakes. The ascending CO₂ forms Ca‐Mg‐HCO₃ type waters by leaching of cations from the fault planes and creates clay minerals, such as kaolinite, as alteration products on affected fault planes. These mineral reactions result in fault weakness and in hydraulically interconnected fault network. This leads to a decrease in the friction coefficient of the Coulomb failure stress (CFS) and to fault creep as stress build‐up cannot occur in the weak segments. At the transition zone in the north of the Cheb Basin, between areas of weak, fluid conductive faults and areas of locked faults with frictional strength, fluid pressure can increase resulting in stress build‐up. This can trigger strike‐slip swarm earthquakes. Fault creep or movements in weak segments may support a stress build‐up in the transition area by transmitting fluid pressure pulses. Additionally to fluid‐driven triggering models, it is important to consider that fluids ascending along faults are CO₂‐supersaturated thus intensifying the effect of fluid flow. The enforced flow of CO₂‐supersaturated fluids in the transitional zone from high to low permeability segments through narrowings triggers gas exsolution and may generate pressure fluctuations. Phase separation starts according to the phase behaviour of CO₂‐H₂O systems in the seismically active depths of NW Bohemia and may explain the vertical distribution of the seismicity. Changes in the size of the fluid transport channels in the fault systems caused, or superimposed, by fault movements, can produce fluid pressure increases or pulses, which are the precondition for triggering fluid‐induced swarm earthquakes.     

Fluid inclusion and stable isotope constraints on the genesis of the Jian copper deposit,Sanandaj–Sirjan metamorphic zone,Iran

The Jian copper deposit, located on the eastern edge of the Sanandaj–Sirjan metamorphic zone, southwest of Iran, is contained within the Surian Permo‐Triassic volcano‐sedimentary complex. Retrograde metamorphism resulted in three stages of mineralization (quartz ± sulfide veins) during exhumation of the Surian metamorphic complex (Middle Jurassic time; 159–167 Ma), and after the peak of the metamorphism (Middle to Late Triassic time; approximately 187 Ma). The early stage of mineralization (stage 1) is related to a homogeneous H₂O–CO₂ (XCO₂ > 0.1) fluid characterized by moderate salinity (<10 wt.% NaCl equivalent) at high temperature and pressure (>370°C, >3 kbar). Early quartz was followed by small amounts of disseminated fine‐grained pyrite and chalcopyrite. Most of the main‐ore‐stage (stage 2) minerals, including chalcopyrite, pyrite and minor sphalerite, pyrrhotite, and galena, precipitated from an aqueous‐carbonic fluid (8–18 wt.% NaCl equivalent) at temperatures ranging between 241 and 388°C during fluid unmixing process (CO₂ effervescence). Fluid unmixing in the primary carbonaceous fluid at pressures of 1.5–3 kbar produced a high XCO₂ (>0.05) and a low XCO₂ (<0.01) aqueous fluid in ore‐bearing quartz veins. Oxygen and hydrogen isotope compositions suggest mineralization by fluids derived from metamorphic dehydration (δ¹⁸O_fluid = +7.6 to +10.7‰ and δD = ?33.1 to ?38.5‰) during stage 2. The late stage (stage 3) is related to a distinct low salinity (1.5–8 wt.% NaCl equivalent) and temperatures of (120–230°C) aqueous fluid at pressures below 1.5 kbar and the deposition of post‐ore barren quartz veins. These fluids probably derived from meteoric waters, which circulated through the metamorphic pile at sufficiently high temperatures and acquire the characteristics of metamorphic fluids (δ¹⁸O_fluid = +4.7 to +5.1‰ and δD = ?52.3 to ?53.9‰) during waning stages of the postearly Cimmerian orogeny in Surian complex. The sulfide‐bearing quartz veins are interpreted as a small‐scale example of redistribution of mineral deposits by metamorphic fluids. This study suggests that mineralization at the Jian deposit is metamorphogenic in style, probably related to a deep‐seated mesothermal system.     

Solubility of quartz in crustal fluids: experiments and general equations for salt solutions and H2O–CO2 mixtures at 400–800°C and 0.1–0.9 GPa

The solubility of quartz has been measured in a wide range of salt solutions at 800°C and 0.5 GPa, and in NaCl, CaCl₂ and CsCl solutions and H₂O–CO₂ fluids at six additional P–T conditions ranging from 400°C at 0.1 GPa to 800°C at 0.9 GPa. The experiments cover a wide range of compositions along each binary. At P–T conditions where the density of pure water is low (0.43 g cm^?3), addition of most salts produces an enhancement of quartz solubility at low to moderate salt concentrations (salt‐in effect), although quartz solubility falls with further decrease in X_H2O. At higher fluid densities (0.7 g cm^?3 and greater), the salt‐in effect is generally absent, although this depends on both the cation present and the actual P–T conditions. The salt‐in effect is most readily produced by chloride salts of large monovalent cations, while CaCl₂ only produced a salt‐in effect at the most extreme conditions of high‐T and low‐P investigated (800°C at 0.2 GPa). Under most crustal conditions, the addition of common salts to aqueous fluids results in a lowering of quartz solubility relative to that in pure water (salt‐out effect). Comparing quartz solubility in different fluids by calculating X_H2O on the basis that all salts are fully associated under all conditions yields higher quartz solubility in solutions of monovalent salts than in solutions of divalent salts, absolute values are also influenced by cation radius. Quartz solubility measurements have been fitted to a Setchenow‐type equation, modified to take account of the separate effects of both the lowering of X_H2O and the specific effects of different salts, which are treated as arising through distinct patterns of non‐ideal behaviour, rather than the explicit formation of additional silica complexes with salt components. Quartz solubility in H₂O–CO₂ fluids can be treated as ideal, if the solvation number of aqueous silica is taken as 3.5. For this system the solubility (molality) of quartz in the binary fluid, S is related to its solubility in pure water at the same P–T conditions, S^o, by: Quartz solubility in binary salt systems (H₂O–RCl_n) can be fitted to the relationship: where salt concentration mRCl_n is expressed as molality and the exponent b has a value of 1 except under conditions where salting‐in is observed at low salt concentrations, in which case it is <1. Under most crustal conditions, the solubility of quartz in NaCl solutions is given to a good approximation by: We propose that quartz solubility in multicomponent fluids can be estimated from an extended expression, calculating X_H2O based on the total fluid composition (including dissolved gasses), and adding terms for each major salt present. Our experimental results on H₂O–NaCl–CO₂ fluids are satisfactorily predicted on this basis. An important implication of the results presented here is that there are circumstances where the migration of a fluid from one quartz‐bearing host into another, if it is accompanied by re‐equilibration through cation exchange, may lead to dissolution or precipitation of quartz even at constant P and T, with concomitant modification of the permeability structure of the deep crust.     

Geochemical fingerprinting of hydraulic fracturing fluids from Qusaiba Hot Shale and formation water from Paleozoic petroleum systems,Saudi Arabia

Provenance studies of produced water are essential to trace flow dynamics and reservoir compartmentalization in petroleum systems and to quantify fluid recovery rates from unconventional fracturing. Produced water from a hydraulically fractured well in the Qusaiba Hot Shale in the Northern Exploration Area, Saudi Arabia, was daily monitored and analyzed for water chemistry, and environmental (δ²H, δ¹³C, δ¹⁸O_H2O, δ¹⁸O_SO4, δ³⁴S_SO4, δ³⁷Cl, ⁸⁷Sr/⁸⁶Sr) and cosmogenic isotopes (³H, ¹⁴C, ³⁶Cl), to differentiate from reference fluids of supply water, fracturing fluids, and formation water from adjacent Paleozoic units. Initially, recovered water is composed of fracturing fluids and subsequently replaced by a homogeneous cut of pristine formation water. Formation water is composed of dominant meteoric water (approximately 84 vol%) and minor fossil evaporated seawater. The young ¹⁴C‐apparent age between 6000 and 6700 years BP and depleted δ¹⁸O/δ²H values for the meteoric component confirm the infiltration of surface water into the Qusaiba Hot Shale interval or adjacent units during the Early Holocene Pluvial Period under cooler and wetter climatic conditions than present, which suggest the presence of a very recent, dynamic hydraulic flow system. ³⁶Cl/Cl ratios between 102 × 10^?15 and 31 × 10^?15 are ambiguous and can be attributed to atmospheric recharge close to the coast, mixing of ³⁶Cl‐enriched Quaternary meteoric recharge with ³⁶Cl‐depleted fossil seawater, and/or hypogene production by U‐Th‐enriched host rock. Produced waters from Qusaiba Hot Shale are within the compositional range of Na‐Cl‐type formation water from Paleozoic reservoir units in northern Saudi Arabia with salinities from 30 000 to 130 000 mg l^?1. As a novel technological approach for exploration wells in Northern Saudi Arabia, multi‐isotopic methods were successfully implemented to quantify flowback volumes from hydraulic fracturing, and to fingerprint pristine formation water or pore water in Paleozoic systems on their provenance, residence time, migration pathways, and secondary alteration processes.     

Fracture mineralization and fluid flow evolution: an example from Ordovician–Devonian carbonates,southwestern Ontario,Canada

Petrography, geochemistry (stable and radiogenic isotopes), and fluid inclusion microthermometry of matrix dolomite, fracture‐filling calcite, and saddle dolomite in Ordovician to Devonian carbonates from southwestern Ontario, Canada, provide useful insights into fluid flow evolution during diagenesis. The calculated δ¹⁸O_fluid, ΣREE, and REE_SN patterns of matrix and saddle dolomite suggest diverse fluids were involved in dolomitization and/or recrystallization of dolomite. The ⁸⁷Sr/⁸⁶Sr ratios of dolomite of each succession vary from values in the range of coeval seawater to values more radiogenic than corresponding seawater, which indicate diagenetic fluids were influenced by significant water/rock interaction. High salinities (22.4–26.3 wt. % NaCl + CaCl₂) of Silurian and Ordovician dolomite–hosted fluid inclusions indicate involvement of saline waters from dissolution of Silurian evaporites. High fluid inclusion homogenization temperatures (>100°C) in all samples from Devonian to Ordovician show temperatures higher than maximum burial (60–90°C) of their host strata and suggest involvement of hydrothermal fluids in precipitation and/or recrystallization of dolomite. A thermal anomaly over the mid‐continent rift during Devonian to Mississippian time likely was the source of excess heat in the basin. Thermal buoyancy resulting from this anomaly was the driving force for migration of hydrothermal fluids through regional aquifers from the center of the Michigan Basin toward its margin. The decreasing trend of homogenization temperatures from the basin center toward its margin further supports the interpreted migration of hydrothermal fluids from the basin center toward its margin. Hydrocarbon‐bearing fluid inclusions in late‐stage Devonian to Ordovician calcite cements with high homogenization temperatures (>80°C) and their ¹³C‐depleted values (approaching ?32‰ PDB) indicate the close relationship between hydrothermal fluids and hydrocarbon migration.     

Long‐term chemical evolution and modification of continental basement brines – a field study from the Schwarzwald,SW Germany

Highly saline, deep‐seated basement brines are of major importance for ore‐forming processes, but their genesis is controversial. Based on studies of fluid inclusions from hydrothermal veins of various ages, we reconstruct the temporal evolution of continental basement fluids from the Variscan Schwarzwald (Germany). During the Carboniferous (vein type i), quartz–tourmaline veins precipitated from low‐salinity (<4.5wt% NaCl + CaCl₂), high‐temperature (≤390°C) H₂O‐NaCl‐(CO₂‐CH₄) fluids with Cl/Br mass ratios = 50–146. In the Permian (vein type ii), cooling of H₂O‐NaCl‐(KCl‐CaCl₂) metamorphic fluids (T ≤ 310°C, 2–4.5wt% NaCl + CaCl₂, Cl/Br mass ratios = 90) leads to the precipitation of quartz‐Sb‐Au veins. Around the Triassic–Jurassic boundary (vein type iii), quartz–haematite veins formed from two distinct fluids: a low‐salinity fluid (similar to (ii)) and a high‐salinity fluid (T = 100–320°C, >20wt% NaCl + CaCl₂, Cl/Br mass ratios = 60–110). Both fluids types were present during vein formation but did not mix with each other (because of hydrogeological reasons). Jurassic–Cretaceous veins (vein type iv) record fluid mixing between an older bittern brine (Cl/Br mass ratios ~80) and a younger halite dissolution brine (Cl/Br mass ratios >1000) of similar salinity, resulting in a mixed H₂O‐NaCl‐CaCl₂ brine (50–140°C, 23–26wt% NaCl + CaCl₂, Cl/Br mass ratios = 80–520). During post‐Cretaceous times (vein type v), the opening of the Upper Rhine Graben and the concomitant juxtaposition of various aquifers, which enabled mixing of high‐ and low‐salinity fluids and resulted in vein formation (multicomponent fluid H₂O‐NaCl‐CaCl₂‐(SO₄‐HCO₃), 70–190°C, 5–25wt% NaCl‐CaCl₂ and Cl/Br mass ratios = 2–140). The first occurrence of highly saline brines is recorded in veins that formed shortly after deposition of halite in the Muschelkalk Ocean above the basement, suggesting an external source of the brine's salinity. Hence, today's brines in the European basement probably developed from inherited evaporitic bittern brines. These were afterwards extensively modified by fluid–rock interaction on their migration paths through the crystalline basement and later by mixing with younger meteoric fluids and halite dissolution brines.     

Development of a multibottle gas‐tight fluid sampler WHATS II for Japanese submersibles/ROVs

This paper summarizes the design and performance of our recently developed gas‐tight fluid sampler WHATS II, especially designed to collect seafloor venting gas‐rich fluid from submersibles/remotely operated vehicles (ROVs). It consists of four 150‐cm³ stainless steel sample cylinders, eight ball valves, a motor‐driven arm, a rail, a peristaltic pump, a control unit, and a flexible Teflon tube connected to a titanium inlet tube. All the parts have been designed to be used at undersea as deep as 4000 m. The motor‐driven arm on the rail can open and close each of the four cylinders. By pumping out distilled water that has filled an open cylinder and the dead spaces of the sampler, we can fill the cylinder with sample fluid. WHATS II can take a maximum of four different gas‐tight samples in a series. The whole operation can be arranged from the cabin, etc., of a submersible/ROV. Use of only one motor to operate eight valves makes the sampler small, light (21 kg in sea water), and easy to handle. In addition, the sampler is able to collect an almost uncontaminated gas‐tight sample from the seafloor. To date, the sampler has been used in more than 90 dive surveys by Japanese submersibles/ROVs, including Shinkai 2000, Shinkai 6500, and Hyper Dolphin, with a success rate of >90%.     

Fluid inclusion and isotopic constraints on the origin of ore‐forming fluid of the Jinman–Liancheng vein Cu deposit in the Lanping Basin,western Yunnan,China

Extensive quartz–carbonate–Cu sulfide veins occur in clastic rocks and are spatially related to Paleocene granites in the western border of the Lanping Basin, western Yunnan, China. Abundant aqueous‐carbonic fluid inclusions occur in these veins but their origin is debated. In the Jinman–Liancheng deposit, individual primary inclusion groups contain either exclusively liquid‐rich inclusions (Gl), or coexisting liquid‐rich and vapor‐rich inclusions (Glv). Microthermometry and estimate of CO₂ content indicate that type Gl inclusions either have homogenization temperatures (Th) 238–263°C and contain c. 3.9–5.5 mole % CO₂, or have Th 178–222°C and contain c. 1.6–3.2 mole % CO₂. Type Glv inclusions are thought to represent samples of fluid unmixing that occurred at 183–218°C. At that time, the liquid phase in the unmixing fluid may contain c. 2.0–3.3 mole % CO₂. As such, the correlation of CO₂ content with Th for type Gl inclusions is thought to be caused by fluid unmixing with decreasing temperature and subsequent CO₂ escape. δ¹⁸O and δD values of the parent water mainly fall in the field below that of primary magmatic water, indicative of fluid derivation from degassed (in open system) magmatic water, with no contributions from basinal or meteoric water. Initial Sr isotopic compositions of hydrothermal carbonates suggest that the fluid was magmatic, probably derived from the Paleogene granites. δ¹³C_PDB values (?4‰ to ?7‰) of the hydrothermal carbonates and δ³⁴S_V‐CDT values of sulfides (mainly ?11‰ to +5‰) indicate that the carbon and sulfur can be derived from (degassed) magma and/or nonmagmatic sources. The CO₂‐rich and magmatic‐water‐derived fluid at Jinman–Liancheng differs from the CO₂‐poor and basinally derived fluid in sediment‐hosted stratiform Cu (SSC) deposits, which suggests that there are no genetic linkages between the vein Cu and SSC deposits in the Lanping Basin.     

Hydraulic observations from a 1 year fluid production test in the 4000 m deep KTB pilot borehole

A long‐term pump test was conducted in the KTB pilot borehole (KTB‐VB), located in the Oberpfalz area, Germany. It produced 22 300 m³ of formation fluid. Initially, fluid production rate was 29 l min^?1 for 4 months, but was then raised to an average of 57 l min^?1 for eight more months. The aim of this study was to examine the fluid parameters and hydraulic properties of fractured, crystalline crusts as part of the new KTB programme ‘Energy and Fluid Transport in Continental Fault Systems’. KTB‐VB has an open‐hole section from 3850 to 4000 m depth that is in hydraulic contact with a prominent continental fault system in the area, called SE2. Salinity and temperature of the fluid inside the borehole, and consequently hydrostatic pressure, changed significantly throughout the test. Influence of these quantities on variations in fluid density had to be taken into account for interpretation of the pump test. Modelling of the pressure response related to the pumping was achieved assuming the validity of linear Darcy flow and permeability to be independent of the flow rate. Following the principle ‘minimum in model dimension’, we first examined whether the pressure response can be explained by an equivalent model where rock properties around the borehole are axially symmetric. Calculations show that the observed pressure data in KTB‐VB can in fact be reproduced through such a configuration. For the period of high pumping rate (57 l min^?1) and the following recovery phase, the resulting parameters are 2.4 × 10^?13 m³ in hydraulic transmissivity and 3.7 × 10^?9 m Pa^?1 in storativity for radial distances up to 187 m, and 4.7 × 10^?14 m³ and 6.0 × 10^?9 m Pa^?1, respectively, for radial distances between 187 and 1200 m. The former pair of values mainly reflect the hydraulic properties of the fault zone SE2. For a more realistic hydraulic study on a greater scale, program FEFLOW was used. Parameter values were obtained by matching the calculated induced pressure signal to fluid‐level variations observed in the KTB main hole (KTB‐HB) located at 200 m radial distance from KTB‐VB. KTB‐HB is uncased from 9031 to 9100 m and shows indications of leakage in the casing at depths 5200–5600 m. Analysis of the pressure record and hydraulic modelling suggest the existence of a weak hydraulic communication between the two boreholes, probably at depths around the leakage. Hydraulic modelling of a major slug‐test in KTB‐HB that was run during the pumping in KTB‐VB reveals the effective transmissivity of the connected formation to be 1 to 2 orders of magnitude lower than the one determined for the SE2 fault zone.     

Solubility of corundum + kyanite in H2O at 700°C and 10 kbar: evidence for Al‐Si complexing at high pressure and temperature

The solubility of the assemblage corundum + kyanite in H₂O was determined at 700°C and 10 kbar, using a piston‐cylinder apparatus and rapid‐quench/fluid‐extraction techniques. Weighted mean concentrations of total Al and Si were 5.80 ± 0.03 mmol kg^?1 H₂O and 0.308 ± 0.003 mol kg^?1 H₂O, respectively (1σ errors). The Al concentration is nearly five times higher than that of corundum solubility in pure H₂O. This difference is interpreted to arise from complexing between Si and Al to form HAlSiO_4,aq species. Charged or more polymerized species are also possible, but their abundance cannot be constrained based on these experiments. Assumption of a single aqueous aluminosilicate complex permits calculation of the thermodynamic consequences of Al‐Si interaction in high‐pressure fluids, as well as phase diagrams for the system Al‐Si‐O‐H. Formation of Al‐Si complexes leads to a large increase in dissolved Al with increasing Si in solution, such that Al concentration in equilibrium with kyanite + quartz is predicted to be 7.1 mmolal, higher than with kyanite + corundum. The elevated concentration of Si in deep‐crustal and mantle aqueous fluids suggests that Al must readily be dissolved and transported by Al‐Si complexing in high‐pressure metamorphic and metasomatic environments. The results provide a simple explanation for the common observation of kyanite + quartz segregations in eclogites and Barrovian metamorphic rocks.     

Contrasting paleofluid systems in the continental basement: a fluid inclusion and stable isotope study of hydrothermal vein mineralization,Schwarzwald district,Germany

An integrated fluid inclusion and stable isotope study was carried out on hydrothermal veins (Sb‐bearing quartz veins, metal‐bearing fluorite–barite–quartz veins) from the Schwarzwald district, Germany. A total number of 106 Variscan (quartz veins related to Variscan orogenic processes) and post‐Variscan deposits were studied by microthermometry, Raman spectroscopy, and stable isotope analysis. The fluid inclusions in Variscan quartz veins are of the H₂O–NaCl–(KCl) type, have low salinities (0–10 wt.% eqv. NaCl) and high T_h values (150–350°C). Oxygen isotope data for quartz range from +2.8‰ to +12.2‰ and calculated δ¹⁸O_H2O values of the fluid are between ?12.5‰ and +4.4‰. The δD values of water extracted from fluid inclusions vary between ?49‰ and +4‰. The geological framework, fluid inclusion and stable isotope characteristics of the Variscan veins suggest an origin from regional metamorphic devolatilization processes. By contrast, the fluid inclusions in post‐Variscan fluorite, calcite, barite, quartz, and sphalerite belong to the H₂O–NaCl–CaCl₂ type, have high salinities (22–25 wt.% eqv. NaCl) and lower T_h values of 90–200°C. A low‐salinity fluid (0–15 wt.% eqv. NaCl) was observed in late‐stage fluorite, calcite, and quartz, which was trapped at similar temperatures. The δ¹⁸O values of quartz range between +11.1‰ and +20.9‰, which translates into calculated δ¹⁸O_H2O values between ?11.0‰ and +4.4‰. This range is consistent with δ¹⁸O_H2O values of fluid inclusion water extracted from fluorite (?11.6‰ to +1.1‰). The δD values of directly measured fluid inclusion water range between ?29‰ and ?1‰, ?26‰ and ?15‰, and ?63‰ and +9‰ for fluorite, quartz, and calcite, respectively. Calculations using the fluid inclusion and isotope data point to formation of the fluorite–barite–quartz veins under near‐hydrostatic conditions. The δ¹⁸O_H2O and δD data, particularly the observed wide range in δD, indicate that the mineralization formed through large‐scale mixing of a basement‐derived saline NaCl–CaCl₂ brine with meteoric water. Our comprehensive study provides evidence for two fundamentally different fluid systems in the crystalline basement. The Variscan fluid regime is dominated by fluids generated through metamorphic devolatilization and fluid expulsion driven by compressional nappe tectonics. The onset of post‐Variscan extensional tectonics resulted in replacement of the orogenic fluid regime by fluids which have distinct compositional characteristics and are related to a change in the principal fluid sources and the general fluid flow patterns. This younger system shows remarkably persistent geochemical and isotopic features over a prolonged period of more than 100 Ma.     

Mobilization of ore fluids during Alpine metamorphism: evidence from hydrothermal veins in the Variscan basement of Western Carpathians,Slovakia

Hydrothermal polymetallic veins of the Gemeric unit of the Western Carpathians are oriented coherently with the foliation of their low‐grade Variscan basement host. Early siderite precipitated from homogeneous NaCl‐KCl‐CaCl₂‐H₂O brines with minor CO₂, while immiscible gas–brine mixtures are indicative of the superimposed barite, quartz–tourmaline and quartz–sulphide stages. The high‐salinity aqueous fluid (18–35 wt%) found in all mineralization stages corresponds to formation water modified by interaction with crystalline basement rocks at temperatures between 140 and 300°C. High brominity (around 1000 ppm in average) resulted from evaporation and anhydrite precipitation in a Permo‐Triassic marine basin, and from secondary enrichment by dissolution of organic matter in the marine sediments at diagenetic temperatures. Sulphate depletion reflects thermogenic reduction during infiltration of the formation waters into the Variscan crystalline basement. Crystallization temperatures of the siderite fill (140–300°C) and oxygen isotope ratios of the parental fluids (4–10‰) increase towards the centre of the Gemeric cleavage fan, probably as a consequence of decreasing water/rock ratios in rock‐buffered hydrothermal systems operating during the initial stages of vein evolution. In contrast, buoyant gas–water mixtures, variable salinities and strongly fluctuating P–T parameters in the successive mineralization stages reflect transition from a closed to an open hydrothermal system and mixing of fluids from various sources. Depths of burial were 6–14 km (1.7–4.4 kbar, in a predominantly lithostatic fluid regime) during the siderite and barite sub‐stages of the north‐Gemeric veins, and up to 16 km (1.6–4.5 kbar, in a hydrostatic to lithostatic fluid regime) in the quartz–tourmaline stage of the south‐Gemeric veins. The fluid pressure decreased down to approximately 0.6 kbar during crystallization of sulphides. U‐Pb‐Th, ⁴⁰Ar/³⁹Ar and K/Ar geochronology applied to hydrothermal muscovite–phengite and monazite, as well as cleavage phyllosilicates in the adjacent basement rocks and deformed Permian conglomerates corroborated the opening of hydrothermal veins during Lower Cretaceous thrusting and their rejuvenation during Late Cretaceous sinistral transpressive shearing and extension.     

Bleached mudstone,iron concretions,and calcite veins: a natural analogue for the effects of reducing CO2‐bearing fluids on migration and mineralization of iron,sealing properties,and composition of mudstone cap rocks

This study investigates the Wangfu Depression of the Songliao Basin, China, as a natural analogue site for Fe migration (bleaching) and mineralization (formation of iron concretions) caused by reducing CO₂‐bearing fluids that leak along fractures after carbon capture, utilization, and storage. We also examined the origin of fracture‐filling calcite veins, the properties of self‐sealing fluids, the influence of fluids on the compositions of mudstone and established a bleaching model for the study area. Our results show that iron concretions are the oxidative products of precursor minerals (pyrite and siderite) during uplift and are linked to H₂S and CO₂ present in early stage fluids. The precipitation of calcite veins is the result of CO₂ degassing and is related to CO₂, CH₄, and minor heavy hydrocarbons in the main bleaching fluids. In our model, fluids preferentially enter high‐permeability fracture systems and result in the bleaching of surrounding rocks and precipitation of calcite veins. The infilling of calcite veins significantly decreases the permeability of fractures and forces the fluids to slowly enter and bleach the mudstone rocks. The Fe²⁺ released during bleaching migrates to elsewhere with the solutions or is reprecipitated in the calcite veins and iron concretions. The formation of calcite veins reduces the fracture space and effectively prevents fluid flow. The fluids have an insignificant effect on minerals within the mudstone. In terms of the chemistry of the mudstone, only the contents of Fe₂O₃, U, and Mo change significantly, with the content of U increasing in the mudstone and the contents of Fe₂O₃ and Mo decreasing during bleaching.     

Real‐time quadrupole mass spectrometer analysis of gas in borehole fluid samples acquired using the U‐tube sampling methodology

Sampling of fluids in deep boreholes is challenging because of the necessity of minimizing external contamination and maintaining sample integrity during recovery. The U‐tube sampling methodology was developed to collect large volume, multiphase samples at in situ pressures. As a permanent or semi‐permanent installation, the U‐tube can be used for rapidly acquiring multiple samples or it may be installed for long‐term monitoring applications. The U‐tube was first deployed in Liberty County, TX to monitor crosswell CO₂ injection as part of the Frio CO₂ sequestration experiment. Analysis of gases (dissolved or separate phase) was performed in the field using a quadrupole mass spectrometer, which served as the basis for determining the arrival of the CO₂ plume. The presence of oxygen and argon in elevated concentrations, along with reduced methane concentration, indicates sample alteration caused by the introduction of surface fluids during borehole completion. Despite producing the well to eliminate non‐native fluids, measurements demonstrate that contamination persists until the immiscible CO₂ injection swept formation fluid into the observation wellbore.