The production and technology of glazed ceramics from the middle ages,found in the saepinum territory (Italy): a multimethodic approach*

A collection of ceramics from the Middle Ages found in Altilia and Terravecchia (the Saepinum area, Campobasso, Italy) were characterized by using different mineralogical analyses to investigate their provenance and production techniques. The body ceramic was investigated using Rietveld phase analysis of X‐ray powder diffraction patterns, X‐ray fluorescence spectrometry and scanning electron microscopy. The chemical compositions of the coatings were measured by scanning electron microscopy and their mineralogical compositions were determined using a particular technique of X‐ray small‐angle scattering (SAS) optimized for studies of thin films. Moreover, the material used for decoration was studied using micro‐Raman spectroscopy. The archaeometric results confirmed the distinction into two different ceramic classes, already individuated from archaeological analysis: the Altilia objects belong to the protomajolica class, whereas the objects from Terravecchia are RMR (ramina‐manganese‐red) ceramics. A comparison between the chemical and mineralogical compositions of good‐quality ceramic objects and those of waste products indicated local production of the ceramics. A sharp distinction was found in the chemical composition of the coatings: the Altilia products have tin‐opacified lead glazes, while the Terravecchia ones have transparent high‐lead glazes. Among the Altilia products, the unsuccessful process that produced a large quantity of discarded materials was attributed to the high lead content of the glazes. In fact, the principal advantage of the high lead content was to make the preparation and application of the glaze suspension easier, but the risk of reduction of lead oxide to metallic lead was greatly increased. Using micro‐Raman spectroscopy, the following minerals were identified as pigments: pyrolusite for the dark colour, malachite for green, lepidocrocite for yellow and hematite for red.     

DISCOVERY AND CHARACTERIZATION OF AN UNKNOWN BLUE‐GREEN MAYA PIGMENT: VESZELYITE*

Blue‐green mosaic and polychrome masks and funerary offerings from the royal tombs of Calakmul, Mexico, were analysed by scanning electron microscope equipped with energy dispersive X‐ray spectroscopy (SEM‐EDS), X‐ray diffraction (XRD), and particle induced X‐ray emission (PIXE). This led to the first identification of the use of veszelyite, a rare hydrated copper‐zinc phosphate, as green pigment. Analyses of a geological sample of this mineral have been done to confirm the characterization of this Mayan pigment, which might help determine pre‐Columbian trade routes of precious and luxury objects in the ancient Maya Classic period (ad 250–800).     

UNIQUE PRE‐ROMANESQUE MURALS IN KOSTOĽANY POD TRÍBEČOM,SLOVAKIA: THE PAINTING TECHNIQUE AND CAUSES OF DAMAGE

Pre‐Romanesque murals at Kosto?any pod Tríbe?om, Slovakia, have been investigated by portable X‐ray fluorescence and by microanalytical methods to identify painting materials (pigments and binders), and to explain the degradation of colours. Today, missing green and blue shades have been reconstructed according to residual concentrations of Cu, which correspond to copper chlorides—products of salt corrosion of the copper carbonates azurite and/or malachite, accelerated by micro‐organisms. As confirmed by powder X‐ray microdiffraction, original minium (Pb₃O₄) has been transformed to brown–black plattnerite (PbO₂). In increased humidity, even insoluble pigments are washing down from the walls and the intensity of colours further diminishes.     

SCIENTIFIC ANALYSIS OF SEVENTH‐CENTURY GLASS FRAGMENTS FROM THE CRYPTA BALBI IN ROME*

Inductively coupled plasma emission spectroscopy, reflectance spectroscopy and X‐ray diffraction were used to study seventh‐century AD glass fragments from the Crypta Balbi in Rome. All the samples were found to be silica‐soda‐lime glasses. Iron determines the colour of blue‐green, green and yellow‐green transparent glasses; chemical composition suggests deliberate addition of iron and/or manganese in about half the samples. Copper was found as the main colourant in red, pale blue and blue‐green opaque fragments; elemental copper acts as an opacifier in red glass, and calcium antimonate in white, pale blue and blue‐green glasses. Detection of antimony in transparent fragments suggests recycling of opaque mosaic tesserae.     

CHARACTERIZATION OF ARCHAEOLOGICAL AND IN SITU SCOTTISH WINDOW GLASS

Scottish window glass from both archaeological sites and historic buildings was examined using portable X‐ray fluorescence (pXRF) and scanning electron microscopy – energy‐dispersive X‐ray micro‐analysis (SEM–EDX). The elemental composition of the glass provides information regarding the materials used and, subsequently, an approximate range of dates of manufacture. pXRF is shown to be more vulnerable than SEM–EDX to the effects of surface corrosion and matrix effects in archaeological samples. The study showed that the production of window glass in Scotland from the 17th century onwards appears to closely parallel that in England. It also demonstrated the potential of pXRF for in situ studies of window glass in historic buildings. pXRF was used to assess two Scottish buildings; one in state care and one in private ownership. The building in state care, the Abbot's House at Arbroath Abbey, showed a uniform glass type, suggesting that the building was re‐glazed completely at some point during the late 19th or early 20th century. The building in private ownership, Traquair House, had a range of glass types and ages, demonstrating a different maintenance and repair regime. This type of data can be useful in understanding historic buildings in the future, particularly if re‐glazing is being considered.     

MINERALOGICAL INVESTIGATIONS OF MEDIEVAL BRICK SAMPLES FROM BÉKÉS COUNTY (SE HUNGARY)

Brick samples from nine archaeological sites representing seven contemporary medieval settlements in Békés County (SE Hungary) were analysed by quantitative X‐ray powder diffraction, optical microscopic, scanning electron microscopic and coupled thermal analytical – evolved gas analytical methods. The aims of this study were to give a mineralogical–petrographical characterization of the brick samples, to gain possible information on the raw clay and the admixed materials, and to determine the firing techniques applied in medieval southeastern Hungary. The mineralogical composition of the samples suggests that the locally extracted clay was mixed with fluvial sand and wheat (Triticum monococcum L.) chaff. The moulded bricks were fired in clamps. The different degrees of calcite consumption suggest that the firing temperature ranged from ～750°C to ～950°C. Moreover, the well‐developed reaction coronas on calcite grains indicate long firing times, lasting perhaps several days.     

CYPRIOT BYZANTINE GLAZED POTTERY: A STUDY OF THE PAPHOS WORKSHOPS

Twenty‐five samples of Byzantine glazed pottery from two archaeological sites between Limassol and Paphos region (Cyprus), dated between the 12th and 15th century ad were studied using micro X‐ray fluorescence spectroscopy, scanning electron microscopy and X‐ray diffraction analysis. It was found that all the glazes contain lead, following the main manufacturing process of medieval pottery in the Mediterranean territory, while some of them contain tin, possibly for better opacity. Furthermore, it is shown that copper, iron and cobalt with nickel are responsible for the decoration colours. Finally, the application of principal component analysis revealed significant differentiation for some of the samples.     

CLIMATE FORCINGS AND THEIR INFLUENCE ON ALPINE HISTORY AS RECONSTRUCTED THROUGH THE APPLICATION OF SYNCHROTRON‐BASED X‐RAY MICROFLUORESCENCE ON LAYERED STALAGMITES*

Solar variability and volcanic activity strongly interact with climate and the environment. Synchrotron radiation X‐ray microfluorescence (micro‐XRF) to an annually laminated Alpine stalagmite confirmed that annual laminae result from hydrological variability and changes in the duration of soil microbial degradation. The latter is modulated by solar variability. At the centennial timescale, growth rate and solar activity appear to be correlated with temperature change, with low temperatures at solar minima. By combining micro‐XRF and absorption spectroscopy techniques (XANES), we also found that speleothems are a new archive of aerosol sulphate related to volcanic activity. Peaks in S‐concentration from c. 5.2 to 5.0 ka bp in an Alpine stalagmite suggest that multiple volcanic sulphate aerosol emissions enhanced Mid‐Holocene summer cooling, thus favouring the preservation of the Alpine Iceman mummy in a persistent ice casket.     

COLOURED OPAQUE GLASS BEADS OF THE MEROVINGIANS*

Monochrome coloured opaque glass beads of the Merovingians have been examined by different analytical methods. A large number of mostly unprepared beads have been measured by X‐ray fluorescence analysis. X‐ray diffraction was used for the identification of the crystalline colouring and opacifying pigments, and electron probe micro‐analysis as well as scanning electron microscopy were applied to study the composition and the microstructure of a white, brown, green, orange and yellow glass bead. After subtracting the content of colouring oxides of the glass beads and normalizing the residual values to 100% an identical soda‐lime‐glass matrix was obtained. The origin of the colouring metal oxides is discussed.     

THE COMPLEMENTARY USE OF NEUTRONS AND X‐RAYS FOR THE NON‐DESTRUCTIVE INVESTIGATION OF ARCHAEOLOGICAL OBJECTS FROM SWISS COLLECTIONS*

This paper shows the possibilities offered by the combined use of non‐destructive neutron and X‐ray beams in archaeological research on metallic finds. The following five artefacts from Swiss excavations were submitted to investigation, each with dedicated aims: a Roman sword, a Roman dagger, an Iron Age bucket, Iron Age spearheads and a Roman finger ring. The images obtained with both methods—neutrons and X‐rays—are discussed in length in this paper. The investigations took place at the Paul Scherrer Institute and the archaeologists who studied the objects come from the Universities of Lausanne and Zurich.     

ASSESSMENT OF THE BINDER IN HISTORICAL MORTARS BY VARIOUS TECHNIQUES

Three different historical mortars, one from the 18th–19th centuries and two from the 12th century, were crushed and sieved to give eight fractions between less than 0.063 mm and 4 mm for each sample. Each fraction was chemically analysed for the amount of calcium carbonate binder, using the reactions with HCl and EDTA and by means of atomic absorption spectroscopy. The samples were also characterized by X‐ray diffraction (XRD) and by low‐temperature nitrogen adsorption isotherms. The limitations and advantages of each of the various methodologies for the determination of the binder are discussed. Reactions with HCl and XRD were shown to be the methods that gave the more coherent results.     

Vietnamese (15th Century) Blue‐And‐White,Tam Thai and Lustre Porcelains/Stonewares: Glaze Composition and Decoration Techniques*

EDS, X‐ray fluorescence, Raman spectroscopy, thermal expansion–shrinkage measurement and scanning electron microscopy were applied to determine the elemental components, structural phases and glazing temperatures of the transparent glazes, blue underglaze and overglaze tam thai (including gold‐like lustre) decorations from the 15th‐century Vietnamese porcelains/stonewares found at the Chu Ðâu–My Xa kiln site and in the Cù Lao Chàm (Hôi An) cargo. The ancient technology for colouring the glazes is discussed. The various blue tones in the underglazed décor result from cobalt‐containing manganese ore, with the intentional addition of iron oxide. The overglaze copper‐green and the gold‐like lustre were obtained by dispersing copper in lead‐based glass. The red colour was made using hematite dispersed in lead‐rich flux.     

PETROGRAPHIC AND CHEMICAL CHARACTERIZATION OF POTTERY PRODUCTION OF THE LATE MINOAN I KILN AT HAGHIA TRIADA,CRETE*

Pottery from the Late Minoan I kiln at Haghia Triada in the Mesara Plain, southern Crete, was analysed by a range of techniques, comprising thin‐section petrography, scanning electron microscopy, X‐ray diffraction, X‐ray fluorescence and neutron activation analysis. The project characterizes the ceramic fabrics and probable raw materials, correlates paste recipes with shape, reconstructs the firing conditions of the kiln and establishes a chemical reference group, taking into account post‐burial alteration and contamination. Comparison of the reference group formed with that from the neighbouring, broadly contemporary, kiln at Kommos shows an unexpected differentiation of the two kilns.     

NATURE AND MICROSTRUCTURE OF GALLIC IMITATIONS OF SIGILLATA SLIPS FROM THE LA GRAUFESENQUE WORKSHOP*

The red glaze (slip) that characterizes the Terra Sigillata potteries greatly contributed to their success during the Roman period. The colour of the slip can in fact be partially explained by the microstructure (crystalline phases, grain sizes) and the physico‐chemistry (composition) of the ceramics. However, the precise process and the diffusion of this technique are still not fully known. In particular, we do not know yet how the production of sigillata took place in the south of Gaul, and the role that was played by the production under Italian influence (pre‐sigillata) preceding the first local sigillata. In this work, a combination of transmission electron microscopy (TEM) and X‐ray synchrotron diffraction techniques was used to study the microstructure of pre‐sigillata slips from the main southern Gaul workshop (La Graufesenque), in order to compare their characteristics with those of high‐quality sigillata. These first results seem to indicate that the antique potters chose clays adapted to their firing conditions and to the type of coating that they wanted to make. These productions cannot be described as an initial phase for the later sigillata production and, rather, seem to correspond to the intention of developing a specific type of pottery only inspired by the famous Italian sigillata forms.     

COOKING AND PAINTED WARE FROM SAN GIUSTO (LUCERA,FOGGIA): THE PRODUCTION CYCLE,FROM THE SUPPLY OF RAW MATERIALS TO THE COMMERCIALIZATION OF PRODUCTS*

Archaeological excavation at the San Giusto site (Lucera, Italy) has unearthed a Late Antique kiln that was most certainly dedicated to the production of cooking ware. An archaeometric study of numerous specimens of cooking and painted ware found at this site was carried out using optical microscopy, scanning electron microscopy, micro‐Raman spectroscopy, X‐ray diffraction, X‐ray fluorescence, inductively coupled plasma mass and optical emission spectrometry and instrumental neutron activation analysis. The integration of historical–archaeological data with archaeometric data has revealed that these specimens can be attributed to the San Giusto site. Furthermore, the production cycle of this ware can thus be reconstructed: from the diversified supply of raw materials (fluvial and marine sediments), to the relatively complex preparation of the paste, to firing at variable temperatures (600–750°C for cooking ware; 850–1050°C for painted ware).     

X‐RAY SUB‐MICRON TOMOGRAPHY AS A TOOL FOR THE STUDY OF ARCHAEOLOGICAL WOOD PRESERVED THROUGH THE CORROSION OF METAL OBJECTS

Wood preserved in the corrosion layer of two early medieval iron objects was examined using X‐ray tomography. A state‐of‐the art multi‐resolution X‐ray tomography set‐up ( http://www.ugct.ugent.be ) provided virtual cross‐sections of the archaeological wood samples at sub‐micron resolution. These were compared with scans of samples of similar modern wood. These scans demonstrate the power of sub‐micron X‐ray tomography for wood identification, although the process of mineralization pushes this technique to its limits. Furthermore, this technique facilitated appraisal of the mineral content of the archaeological wood, which is useful in selecting the most appropriate strategy for the (preventative) conservation of the archaeological object.     

ANALYSING ARCHAEOLOGICAL BASALT USING NON‐DESTRUCTIVE ENERGY‐DISPERSIVE X‐RAY FLUORESCENCE (EDXRF): EFFECTS OF POST‐DEPOSITIONAL CHEMICAL WEATHERING AND SAMPLE SIZE ON ANALYTICAL PRECISION*

Energy‐dispersive X‐ray fluorescence (EDXRF) has been commonly used to determine geological sources of volcanic glass artefacts, but its ability to discriminate between basaltic sources is less developed. We examine the precision and accuracy of non‐destructive EDXRF for basalt artefacts by analysing varying size and weathering characteristics. The experiments identified no appreciable effect in reproducibility or measured composition due to thickness (down to 1 mm) or natural weathering of pre‐contact flake scars for the 17 elements measured in this study. Samples with surface area less than 100 mm², however, show significant variability in measured composition and reproducibility.     

PREHISTORIC WALL PAINTINGS: THE CASE OF THE DOMUS DE JANAS NECROPOLIS (SARDINIA,ITALY)*

The Domus de Janas (Home of the Fairies, or Home of the Witches) are Neolithic hypogea located throughout Sardinia (Italy) and decorated with red and black wall paintings. The objective of this study was to define the painting technique through the analytical characterization of the pigments and binding media. Samples of painting film from different graves have been examined by means of various analytical techniques. XRD, Raman and SEM–EDX analyses identified the red and black pigments respectively as red ochre rich in hematite and carbon black, while GC–MS analyses characterized the organic binder as egg.     

THE APPLICATION OF A PORTABLE X‐RAY FLUORESCENCE SPECTROMETER TO THE ON‐SITE ANALYSIS OF GLASS VESSEL FRAGMENTS FROM SOUTHERN THAILAND*

Ancient glass vessel fragments belonging to the seventh to ninth centuries ad , from the Ko Kho Khao, Laem Pho and Khuan Lukpad sites in southern Thailand, were studied. The glass vessel fragment samples are a collection belonging to the Department of Archaeology, the 15th Regional Office of Fine Arts of Thailand. The chemical compositions of the glasses were analysed using a modified portable energy‐dispersive X‐ray fluorescence spectrometer (OURSTEX 100FA‐II) by the introduction of a MOXTEK^® AP3.3 polymer window (5 mm²?) to the KETEK silicon drift detector for the measurement of light elements. The non‐destructive analysis was performed at the National Museum, Phuket, in Thailand. It is shown that the glass chemical compositions belong to mineral and plant‐ash based soda–lime–silicate glass. The origins of the glass artefacts are discussed in terms of raw materials and glass decoration, and compared with previously reported similar typological glasses from sites in the port city of Rāya and the Monastery of Wadi al‐Tur in Egypt.