河曲坪头遗址龙山时期陶器及其制陶原料的化学成分分析

为了对山西省忻州市河曲坪头遗址出土的龙山时期的陶器以及制陶原料中的粘土原料的种类和来源进行相关探讨,利用ICP-OES对出土的陶器、坯料,以及遗址附近采集的土样进行了化学成分测试,并使用SPSS软件对分析结果进行了降维处理和主成分分析。结果显示:坪头遗址不同质地的陶器陶土原料相同,只是在钙含量方面存在细微差异。制作陶器所用的粘土原料很可能取自附近的红色古土壤层。该遗址是古人在当地制作陶器的一个场所。     

徐州狮子山汉楚王陵彩绘陶俑的保护研究

为对徐州狮子山出土的彩绘陶俑进行保护,我们对陶俑本体进行了分析,采用扫描电子显微镜（SEM）对陶俑表面进行微观形貌分析;X射线荧光光谱仪（XRF）分析化学成分;通过岩相分析,并结合XRD分析、热重和差示热分析（TG-DSC）从而推测陶俑的烧成温度;电子能谱仪（EDS）对彩绘表面颜料的进行成分分析。在此基础上,采用7种化学材料进行对比实验,对外观、颜色光泽度变化、固化物形成期、防水接触角、吸湿等温线、吸水率、抗压强度进行了观察和分析,同时,还进行了紫外光耐老化试验。试验表明,氟橡胶不仅有较好的渗透率和膜层外观及相对较强的抗压能力的优点,而且还有较好的耐老化性能。经过对狮子山出土的一尊彩绘陶俑利用氟橡胶进行保护后10多年的观察,陶俑的表面色泽、防水与接触角、颜料表面的固结强度等状态保持良好。因此,在保护彩绘陶俑方面,氟橡胶是值得考虑的一种材料。     

山东香山汉墓出土陶质彩绘文物材质及制作工艺的初步研究

山东青州香山汉墓陪葬坑出土了数量巨大,种类齐全陶质彩绘文物,尤其是陶马和陶俑上的彩绘保存完好,色彩鲜艳,绘画工艺精湛,非常罕见。为了研究汉代彩绘及其制陶工艺等信息,本研究使用拉曼光谱(RS)、带能谱的扫描电镜(SEM-EDX)、偏光显微镜(PLM)、体式显微镜(OM)、X射线荧光光谱(XRF)、X射线衍射(XRD)、热膨胀仪等分析方法,对出土的陶质彩绘文物进行了分析研究。结果表明这批陶质彩绘文物制作工艺是就地取土,与水混合塑型,在900~1000℃烧制陶胎。其彩绘所使用的颜料均为矿物颜料,其中白色为方解石(CaCO3)、红色为赭石(Fe2O3)和朱砂(HgS)、黑色为炭黑(C)、紫色为人造汉紫(BaCuSi2O6),采用胶料调和颜料调涂刷绘制而成。这批文物的制作工艺属于典型的秦汉时期彩绘陶器的制作方法。研究成果可为相关文物的保护提供科学数据。     

Characterization of Iron age pottery from eastern Turkey by laser- induced breakdown spectroscopy (LIBS)

Selected pottery sherds coming from the Ayanis, Dilkaya and Karagündüz excavations in eastern Turkey and dated from the Early to Middle Iron Age were examined as regards their composition by using laser-induced breakdown spectroscopy (LIBS). The objective of the study was first to investigate the potential of the LIBS technique in the compositional analysis of pottery and further to explore correlations in spectral data, by using chemometrics methods that would possibly enable discrimination among different sherds. This work is part of a broader study aiming to examine clay variability both before and during the Urartian State period and to explore possible relationships and differences among pottery objects from fortresses and settlements or settlements and cemeteries on the basis of the clay composition of sherds. Preliminary results demonstrate that by using the LIBS technique it is possible to analyse pottery sherds in qualitative and semi-quantitative ways, providing information on the clay and slip composition. Furthermore, encouraging results have been obtained by carrying out principal component analysis (PCA) on the LIBS spectra, which suggest that in certain cases, it is possible to directly correlate spectral information with the origin of pottery sherds.     

Firing Techniques of the Impasti from the Protohistoric Site of Concordia Sagittaria (Venice)

⁵⁷Fe Mössbauer spectroscopy provided relevant information on the firing techniques employed in manufacturing concotto and coarse pottery, two types of fired clay mixtures (impasti) of the protohistoric settlement site of Concordia Sagittaria. The firing techniques of Concordia were reconstructed by comparing the Mössbauer patterns of the artefacts with those of the local raw clays fired in the laboratory. The concotto was produced in kilns by firing clay mixtures under oxidizing conditions at 700–1000°C, or at lower temperatures in the open air. The firing of these clay mixtures containing mainly ground pieces of waste pottery, resulted in hard and variously coloured construction materials, particularly suitable for humid environments. In turn, the coarse pottery was produced by firing clay mixtures more homogeneous than those used for the artefacts of concotto. The firing of coarse pottery was performed under reducing conditions at about 900°C with a final exposure to air by opening the hot kiln. Light and agreeable coarse pottery, with a red surface on the grey-black core, was obtained when the effective temperature of air was higher than 500°C.     

SCIENTIFIC INVESTIGATIONS OF THE SOPRON-KRAUT ACKER IRON AGE POTTERY WORKSHOP

Excavations at the Celtic settlement of Sopron-Krautacker (W. Hungary) make it possible to form an overall view on the local practice of pottery manufacture. Study of the soil conditions has established that the source of raw material is the nearly calcium carbonate-free upper layer of the local soil resulting from a leaching process. By the various analytical methods used (XRD, XRF spectroscopy, and thermal analysis) composition of the pottery has been determined, and it has been shown that the vessels were fired at 600–700 °C.     

Archaeometric study of medieval pottery excavated at Stari (Old) Ras,Serbia

A combined study of a series of polychromatic and monochromatic glazed medieval pottery shards excavated from the archaeological area of Stari (Old) Ras in southern Serbia, including petrographic and chemical analysis, powder X-ray diffraction (PXRD) and Fourier transform infrared (FTIR) spectroscopy, allowed us to clearly distinguish between two groups of ceramics. Ras pottery, made of fine-grained well-cleaned clay and characterised by a rich mineral assemblage, was produced by firing in a temperature range between 800 and 900 °C. Reljina Gradina ceramics were produced at similar temperatures from materials which, with regard to mineralogical and chemical composition, show clear similarity with local clay, suggesting that these samples are of local origin and production. This work is the first systematic archaeometric study of medieval pottery excavated on the territory of Serbia.     

穆斯堡尔谱技术在考古研究中的应用

穆斯堡尔谱技术是研究固体物质超精细相互作用的有效手段之一,与其它多种测试方法相比,穆斯堡尔谱方法以其高分辨率、高灵敏度、强抗干扰能力,及其对试样的无破坏性等而广泛应用于考古研究中。本文主要介绍穆斯堡尔谱技术在古陶制品、古瓷器及釉彩、古代铜制品及其他金属制品、古代壁画等考古研究中的应用,并对其发展进行评价与展望。     

利用同墓葬出土泥芯、陶器示踪青同器铸造地初探 一以湖北襄樊部分东周墓为例

为研究出土墓葬青铜器铸造地,利用X射线荧光光谱法对湖北襄樊的余岗、沈岗、团山、陈坡四处墓地出土的部分青铜器泥芯、陶片进行测试分析,试验结果与山西侯马、武汉盘龙城遗址进行比较分析。对比研究显示,襄樊地区泥芯与当地墓土、陶片在常量元素上具有高度一致性,而与黄河流域的侯马和长江中下游的盘龙城有明显区别,说明襄樊地区这部分铜器应为本地铸造,暗示江汉流域存在自己特有文化。本项研究工作首次尝试利用同墓葬陶器化学成分探索青铜器铸造地,是泥芯研究青铜器铸造地的重要补充,泥芯和陶器相互配合,为青铜器铸造地研究提供了一种新思路。     

Archaeometric Investigation of Medieval Pottery from Excavations at Novo Brdo,Serbia

Medieval pottery from excavations at Novo Brdo, Serbia, an important mining and trading centre during the 14th and 15th centuries, was investigated by a combination of optical microscopy, inductively coupled plasma – optical emission spectrometry, Fourier transform infrared, micro‐Raman and energy‐dispersive X‐ray fluorescence spectroscopy and X‐ray powder diffraction methods in order to determine its composition and firing temperature. The samples investigated were made of medium‐ to coarse‐grained, non‐calcareous clay, by a relatively well‐controlled firing procedure in an oxidizing atmosphere. The firing temperature was estimated to be 850–950°C. The similarity between the chemical composition of the investigated pottery and the local raw clay, combined with the outward appearance and the archaeological findings, indicate domestic production. The pottery is covered with the transparent lead‐rich glaze. Iron and copper were used as colourants.     

Multi-method (FTIR,XRD, PXRF) analysis of Ertebølle pottery ceramics from Scania,southern Sweden

A combination of Fourier-transform infrared spectroscopy (FTIR), powder X-ray diffraction (XRD) and portable X-ray fluorescence spectroscopy (PXRF) was used on the clay fraction of Ertebølle ceramics from several Late Mesolithic sites in Scania, southern Sweden. The aim was to provide up-to-date information about clay types used during that period within the Scanian Ertebølle cultural unit, and to elucidate social aspects relevant to the organization of pottery production and the role of ceramics in the local societies. The results suggest similar clay preferences across the sites, site-based pottery production using local clays and zero mobility of ceramics between the sites. The chemical separation of the ceramics from the site of Soldattorpet into two compositional groups suggests possible multigroup occupation. The origins of aromatic hydrocarbons, extracted previously from the ceramic matrix of the vessels during a lipid residue study, were also investigated, and a discussion is provided.     

EDXRF analysis of pigment used for the decoration of Mleiha pottery

Energy dispersive X-ray fluorescence spectroscopy was utilized for the analysis of the elemental composition of pigment used to decorate pottery artifacts belonging to the Mleiha period (3rd c. B.C–3rd c. A.D).     

On the provenance and manufacture of red-slipped fine ware from ancient Cassope (NW Greece): evidence by X-ray analytical methods

Energy-dispersive X-ray fluorescence spectroscopy was used to characterize red-slipped pottery (2nd–1st century BC) from ancient Cassope, north-western Greece. The compositional data were statistically treated by principal component analysis and chemical groups were established, representing locally produced and imported items. Mineralogical investigation by X-ray diffraction indicated firing temperatures in the range from 850 to 1000 °C for most of the sherds, while one group consisted of over-fired items, possibly in excess of 1050 °C. The morphology and elemental composition of the ceramic bodies and surface slips were examined through scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. The analyses revealed that different pottery groups exhibit surface slips of different nature, in terms of thickness, degree of vitrification and elemental composition. Overall, the diversity in technological characteristics of the examined sherds is indicative of the socio-economic conditions prevailing in Cassopaea during the late Hellenistic period.     

CYPRIOT BYZANTINE GLAZED POTTERY: A STUDY OF THE PAPHOS WORKSHOPS

Twenty‐five samples of Byzantine glazed pottery from two archaeological sites between Limassol and Paphos region (Cyprus), dated between the 12th and 15th century ad were studied using micro X‐ray fluorescence spectroscopy, scanning electron microscopy and X‐ray diffraction analysis. It was found that all the glazes contain lead, following the main manufacturing process of medieval pottery in the Mediterranean territory, while some of them contain tin, possibly for better opacity. Furthermore, it is shown that copper, iron and cobalt with nickel are responsible for the decoration colours. Finally, the application of principal component analysis revealed significant differentiation for some of the samples.     

The Provenance of Red Figure Vases From Locri Epizephiri (Southern Italy): New Evidence by Chemical Analysis

Thirty‐nine samples of red figure pottery found at Locri Epizephiri were analysed for 18 chemical elements by inductively coupled plasma emission spectroscopy. The finds, dated from the end of the sixth to the fourth century bc , were assigned to Attic, Sicilian and Locrian workshops due to their style of execution. Prior to facing the archaeological questions, possible biases on sample classification due to variable firing conditions, or to alteration during burial, were investigated: the results supported the opportunity of a refiring pre‐treatment. Multivariate statistical treatment of the analytical data confirms the separation between Attic and non‐Attic samples; comparison with the composition of black gloss pottery suggests that all the non‐Attic red figure vases could be the output of Locrian workshops.     

安徽怀宁孙家城遗址夹植物陶器初步研究

本文分别采用微观结构观察、成分分析和吸水率-密度测定等方法,对比共出的夹砂陶和泥质陶,对孙家城遗址较为典型的夹植物陶进行分析。陶器坯体微观结构显示夹植物陶疏松多孔,植物类孱和料呈现的形式主要有植物碎屑、炭化颗粒、植物印痕等,应与夹炭陶相区别。成分分析表明夹砂陶、泥质陶和夹植物陶所用的制陶原料存在差异性且一定程度上有重合,后两者在制作工艺上有相似之处且有别于夹砂陶,而且夹植物陶鼎的口沿、腹部、足部的原料和制作工艺也不同。陶器胎体断面元素含量的变化可能是制陶过程中有意为之,也或与烧制过程和器表施加陶衣相关。吸水率-密度分析显示夹植物陶的质地最为疏松多孔,质量最轻,而且吸水饱和后更为脆弱易碎。     

INSIGHTS FROM THE ANALYSIS OF ANGEL MOUNDS POTTERY TROWELS

Archaeologists have recovered pottery trowels in excavations at numerous historic and pre-Columbian archaeological sites in North America since the late nineteenth century. Despite these facts, pottery trowels have not been the subject of thorough scientific analysis or interpretation. In this study, I define and implement a new method of analysis for pottery trowels, using a sample of 188 pottery trowels from the Mississippian site of Angel Mounds (12VG1). After describing the quantitative and qualitative attributes of pottery trowels, I define categories of frequently occurring pottery trowel bell and handle types. The extensive variability of pottery trowel shapes and sizes discovered at Angel Mounds is then discussed with regard to alternative or multiple uses for the tools and the spatial and temporal distributions of pottery trowel types. As an artifact type that provides opportunities to analyze technology, craft production and specialization, and daily practices in past societies, I argue pottery trowels may hold important future insights into a number of topics of interest to archaeologists.     

河南焦作化电集团西晋墓发掘简报

2003年10月焦作市文物工作队发现一座西晋墓(2003JHM1),清理出武士俑、牛车、角兽、马、灶、井、多子槅、俑等文物23件(套)。根据墓葬形制与随葬品判断此墓时代为西晋中期。     

Radiocarbon pottery dating: the chemical compounds of organic fractions, the reliability of 14C dates (preliminary results)

In recent times, a large number of radiocarbon dates appeared for the Southern Neolithic on the basis of pottery dating because other organic matter has practically not been preserved. There are two organic fractions of pottery useful for dating: food residues and carbon from the pottery matrix itself. Food residues are often dated, but this material is not always preserved and is prone to being removed during the cleaning of the pottery. The clay mass of the pottery contains carbon, often directly visible upon breaking of the pottery. The article focusses on determining the chemical composition of the organic fractions in the pottery and the origin of the carbon. For this aim we used the nuclear magnetic resonance (NMR) method to identify the chemical compounds in the food residue and in the pottery matrix. As an example we used pottery from the Neolithic sites: Zamost??e (Central Russia) and the Varfolomeevskay sites (Southern European Russia, Low Volga region) from archaeological collections. The results obtained demonstrate that the food residue and the pottery matrix contain practically the same organic compounds, even if the relative abundances of various compounds are different in these materials. The origin of the carbon from pottery is discussed.     

出土陶器现场保护研究的现状

对出土陶器的现场保护,主要包括出土陶器的提取方法和技术,对酥脆陶器和彩绘陶器的预加固处理,简单的清洗及运输中的保护与缓冲包装技术.