A Study Of The Firing Technique Of Pottery From Kaman‐Kalehöyük,Turkey, by Synchrotron Radiation‐Induced Fluorescence X‐Ray Absorption Near‐Edge Structure (Xanes) Analysis*

Fe K‐XANES spectra of a series of pottery sherds excavated from the archaeological site of Kaman‐Kalehöyük, Turkey, were measured to reveal the firing technique of the pottery. The analysis disclosed relationships among the chemical form of the iron, the firing conditions and the colour of the pottery. The pottery referred to as ‘Grey Ware’ found at this site was classified into two groups according to the chemical form of the iron. Also, it was revealed that the Iron Age pottery referred to as ‘Cream Ware’ was produced first under reducing conditions, and then fired under oxidizing conditions.     

NEUTRON ACTIVATION PATTERNING OF ARCHAEOLOGICAL MATERIALS AT THE NATIONAL CENTER FOR SCIENTIFIC RESEARCH ‘DEMOKRITOS’: THE CASE OF BLACK‐ON‐RED NEOLITHIC POTTERY FROM MACEDONIA,GREECE

A short history of the application of NAA in the characterization of archaeological materials at the National Center for Scientific Research ‘Demokritos’, Athens, is presented. NAA was first applied in archaeology in 1974 at the Radioanalytical Laboratory, and since 1989 has been one of the primary analytical techniques of the ‘Demokritos’ archaeometry programme. A case study is also presented, concerning chemical patterning of the black‐on‐red Neolithic pottery class from Macedonia. Four chemical groups were identified, each corresponding to a different area of production. It is shown that this standardized concept of pottery technology and style was spread out within at least eastern Macedonia.     

A NEW METHOD FOR EXTRACTION,ISOLATION AND TRANSESTERIFICATION OF FREE FATTY ACIDS FROM ARCHAEOLOGICAL POTTERY

This paper presents evidence for increased recovery of organic residues from archaeological pottery through use of a microwave‐assisted liquid chromatography protocol. C_16:0 and C_18:0 saturated fatty acids were obtained from archaeological potsherds recovered from nine Neolithic settlements in the Middle East dating between 4700 and 7300 cal bc , including materials that had not produced evidence for the survival of any lipid species through use of ‘conventional’ solvent extraction techniques. Compound‐specific isotopic analyses of C_16:0 and C_18:0 fatty acids in potsherd extracts subsequently revealed δ¹³C/δ¹²C compositions consistent with modern subcutaneous fats of wild boar and goats pastured on lands adjacent to the Jordan Valley, and residues from a modern pottery vessel used in the manufacturing of butter, cheese and yogurt in central Turkey. These results are presented as an illustration of capabilities of the microwave‐assisted recovery protocol. The reclamation of saturated and unsaturated fatty acids from archaeological pottery fragments recovered from a number of the earliest ceramic horizons in the Middle East is herewith reported, and the extraction methods and instrumental analytical techniques are described.     

THE HISTORY OF THE LAWRENCE BERKELEY NATIONAL LABORATORY INSTRUMENTAL NEUTRON ACTIVATION ANALYSIS PROGRAMME FOR ARCHAEOLOGICAL AND GEOLOGICAL MATERIALS

The Lawrence Berkeley National Laboratory pottery provenance group developed standards and instrumental neutron activation analysis (INAA) methods that are used at many archaeometry laboratories around the world. The background and development of ‘Standard Pottery’ and of methods for INAA are described. Early pottery provenance studies are described, and other research programmes, involving obsidian and magmatic mixing, the origin of the stone used for the Colossi of Memnon, and the ‘Plate of Brass’, are mentioned. Research work by the Laboratory included the discovery of the world‐wide iridium anomaly and extensive subsequent research on what has come to be known as the ‘Asteroid Impact Theory’. Characteristics of the analytical programme for pottery provenance work, including overall aims, precision and accuracy, intercalibration, and irradiation and measurement protocols, are discussed. New research areas developed in the past 15 years, to broaden the usefulness of chemical compositional data for archaeological investigation, and examples of recent work, are described. This research, which makes use of high‐precision X‐ray fluorescence analysis in addition to INAA measurements on sample splits, includes distinguishing the products of different workshops located at the same production site, studies on the significance of the distribution of silver in archaeological pottery and the use of high‐precision chemical compositional data as an aid for making chronological distinctions.     

ARCHAEOLOGICAL AND CHEMICAL RESEARCH ON SEDIMENTS AND CERAMICS AT POLIDEPORTIVO (SPAIN): AN INTEGRATED APPROACH*

This paper proposes a preliminary approach to the integration of archaeological evidence and various chemical analyses (phosphorus and lipid) on sediments and ceramics. Phosphorus and organic matter analyses are, thus, used for the study of sediments, and lipid analyses for pottery from structure 19 of the Late Neolithic—Early Copper site known as ‘Polideportivo’, Martos, southern Spain. The results of both types of analysis point to a predominantly domestic function for this structure.     

CLAY RESOURCES AND TECHNICAL CHOICES FOR NEOLITHIC POTTERY (CHALAIN,JURA, FRANCE): CHEMICAL,MINERALOGICAL AND GRAIN‐SIZE ANALYSES*

Many authors have considered pottery manufacturing constraints and sociocultural elements as factors in change in past civilizations over time. The main issue of this research is to better understand the reasons for changes, or choices, in pottery raw materials. The very precise and detailed stratigraphy and cultural succession of occupations is based on dendrochronological data from the lake‐dwelling sites of Chalain (Jura, France). Petrographic, palaeontological and chemical analyses were used to determine the nature and origins of the raw materials used by the Neolithic potters. Stratigraphy and dendrochronological data were used to reconstruct in detail the evolution dynamics of fabric changes. Several raw material sources were identified for many of the pottery groups. Each of them was sampled for qualitative experimental tests of pottery forming. The experimental results show a high variability between the sediments tested. This variability was quantitatively estimated by XRF, XRD, the Rietveld method, calcium carbonate quantification and laser grain‐size analyses of matrices, indirect measures of plasticity. These analytical results allow a better understanding of the differences observed in the experimental tests. On the basis of these experimental and analytical results, changing parameters such as pottery manufacturing constraints, mineralogical characteristics of raw materials and sociocultural factors are considered. In conclusion, all the social and technical parameters, in each archaeological context, must be taken into account for a better understanding of the changes occurring throughout the chronological sequence.     

PLAIN POTTERY AND SOCIAL LANDSCAPES: REINTERPRETING THE SIGNIFICANCE OF CERAMIC PROVENANCE IN THE NEOLITHIC

This paper focuses on plain, stylistically unvaried pottery from three Late Neolithic sites from the Mondego Plateau, Portugal, and investigates ceramic production and exchange among small‐scale prehistoric societies by means of thin‐section petrography and chemical analysis (INAA). The results show that the majority of the pottery was made with widely available, granite‐derived sedimentary clays, but petrographic differences between fabrics indicate collection at multiple locations within these deposits. Variation in chemical composition is consistent with site‐specific sourcing areas, while comparison with data from earlier sites in the Mondego and surrounding mountains suggests that such sources were geographically restricted within the plateau. In contrast, the small percentage of vessels produced with residual clays of metamorphic and intermediate igneous origin, which outcrop over 10 km and 30 km from the archaeological sites, demonstrates that plain pottery did circulate during the Neolithic beyond the funerary sphere. This is the product of the routines of mobility and social networks of Neolithic groups across the wider landscape, which involved the exchange of ‘mundane’ vessels. Finally, the study demonstrates that micro‐regional provenance studies can provide significant insights into prehistoric social landscapes if the data are interrogated beyond simplistic classifications of local and non‐local.     

ARCHAEOMETRIC ANALYSES ON ‘CORINTHIAN B’ TRANSPORT AMPHORAE FOUND AT GELA (SICILY,ITALY)*

The aim of this work is to throw light on the archaic production of ‘Corinthian B’ amphorae, which are widely diffused in the Western Mediterranean basin and are also present in Greece, but whose geographical provenance is still under discussion. We analysed a group of 37 samples belonging to different ceramic classes dated to the sixth and fifth centuries bc . In particular, there were 19 sherds of trade amphorae of the so‐called archaic ‘Corinthian B’ type, from archaeological excavations in Gela (Sicily, Italy). As a comparison, we also investigated 18 samples of tiles and local coarse pottery from Sibari (Calabria, Italy). The samples were analysed using different techniques, such as optical analysis with a polarized‐light microscope (OM), X‐ray diffraction (XRD), Fourier transform–infrared absorption (FT–IR) and inductively coupled plasma–optical emission spectroscopy (ICP–OES). The combination of these complementary analytical methods allowed us to characterize the samples, determine their firing temperatures and identify the probable provenance. The study of thin sections of sherds by OM allowed us to divide the investigated amphorae into two main groups: the first was characterized by a composition that suggested a Western provenance, in particular from the Calabrian–Peloritan region; the second one was very similar to the ‘Corinthian B’ amphorae that come from Corinth and have been classified as ‘fabric class 1’ by Whitbread (1995 ). The XRD and FT–IR results permitted us to determine the mineral composition of the findings and to estimate their firing temperature. The ICP–OES technique was particularly useful in identifying the production centres. In fact, in the studied pottery, this analysis revealed Ni and Cr values that were noticeably different between Greek and southern Italian production.     

A STUDY ON LATE MEDIEVAL TRANSPARENT‐GLAZED POTTERY AND ARCHAIC MAJOLICA FROM ORVIETO (CENTRAL ITALY)*

Nineteen samples of medieval transparent‐glazed pottery and archaic majolica from Orvieto (central Italy) were studied. They were classified by archaeological criterion as follows: five transparent‐glazed fragments with green and brown decorations (first half of the 13th century), eight green transparent‐glazed fragments (13th century) and six tin‐glazed fragments with green and brown decorations (second half of the 13th century). SEM–EDX, XRD (the Rietveld method) and XRF were used to characterize the chemical and mineralogical compositions both of the bodies and the coatings. In all of the samples, the paste is Ca‐rich with CaO contents as high as 13–20 wt%. The mineralogical composition is compatible with a firing temperature of about 950°C, which is the typical temperature reached in a wood kiln. No difference was observed between the bodies of transparent‐ and tin‐glazed pottery. In the case of transparent glazes, the burial conditions lead to heavy weathering of the samples. However, on the basis of the analyses carried out in non‐weathered areas, the typical composition is PbO 55–65 wt%, SiO₂31–35 wt%. In tin glazes, the tin is scattered on the mass of the glaze as SnO₂crystals with a concentration of 7–14 wt%. Concerning the decorations, it is established that the green colour is due to the presence of copper, while manganese is responsible for the brown colour. These pigments, which represent the typical colours of ‘archaic majolica’, are spread through the glaze homogeneously, apart from one case in which there is clear evidence of manganese oxide crystals.     

SEM–EDS ANALYSIS AS A RAPID TOOL FOR DISTINGUISHING CAMPANIAN A WARE AND SICILIAN IMITATIONS

The aim of this work is to examine whether it is possible to find chemical markers that allow a distinction to be made between the imported black glossed ‘Campanian A’ and the Sicilian imitation (end of fourth to first century bc ) of these productions by carrying out quantitative chemical microanalysis of the slip using the SEM–EDS technique. The efficiency of the proposed analytical method has been tested on a set of ceramic samples corresponding to Sicilian black gloss imitations whose ceramic body has already been characterized petrographically by thin‐section microscopy and chemically by XRF. The analytical data point to Na₂O as a suitable chemical marker to distinguish between original ‘Campanian A’ imported from the Gulf of Naples area and Sicilian imitations of the same forms of Hellenistic pottery. In order to verify the above result, the enrichment factors (EFs) between the raw clays, the corresponding ceramic body and black gloss slip were calculated. Some differences in the patterns of EFs between original ‘Campanian A’ and Sicilian imitations were recognized and explained. Therefore, the obtained results can help to accomplish a first distinction between imported and local material on a firm analytical basis, working on a statistically significant number of individuals.     

STATISTICAL ASPECTS OF POTTERY QUANTIFICATION FOR THE DATING OF SOME ARCHAEOLOGICAL CONTEXTS*

This paper describes some statistical analyses of a particular archaeological material (pottery) originating at some sites in the city of Tours. An important part of the archaeological study of pottery is the comparison of ceramic assemblages to establish the absolute dates of contexts. In this paper, a statistical model is built to assess this comparison. The statistical procedure uses classical tools (correspondence analysis, linear regression and resampling methods) in an iterative scheme. Archaeologists may find in the paper a useful set of known statistical methods, while statisticians can learn a method of ‘arranging’ well‐known techniques. No method is new, but their combination is characteristic of this application.     

THE DISCOVERY OF ANOMALOUSLY HIGH SILVER ABUNDANCES IN POTTERY FROM EARLY ROMAN EXCAVATION CONTEXTS IN JERUSALEM*

This is the first study on the differential distribution and concentrations of silver in ceramics recovered from archaeological excavations. The chemical compositions of 1174 pottery vessels from 38 Roman‐period sites in Israel have been determined. Unusually high and variable abundances of silver were discovered in pottery samples of all vessel types and chemical compositions from four distinct archaeological contexts dating to late first century bce to 70 ce Jerusalem. The large majority of the Jerusalem vessels could be distinguished by their silver abundances from all analysed pottery pieces recovered at rural sites outside Jerusalem, even when the pottery types and chemical compositions, except for silver, of pottery found within and outside Jerusalem were indistinguishable. The evidence is suggestive of a human origin for the high and variable silver abundances, and dispersion of the silver by aqueous transport. The differential silver concentrations found in excavated pottery from Jerusalem and other urban and rural sites suggest that attention to the distribution of silver in pottery from excavated contexts may be helpful for evaluating the nature and function of archaeological remains and patterns of urban contamination.     

EXPERIMENTAL EVIDENCE FOR THE PROCESSING OF MARINE ANIMAL PRODUCTS AND OTHER COMMODITIES CONTAINING POLYUNSATURATED FATTY ACIDS IN POTTERY VESSELS*

ω‐(o‐Alkylphenyl)alkanoic acids are known to form in vitro from triunsaturated fatty acids following protracted heating. These compounds have recently been identified in absorbed lipid extracts obtained from archaeological pottery vessels, providing a potentially valuable new class of indicator for the processing of commodities, such as marine oils, which contain high abundances of polyunsaturated fatty acids. Experiments were conducted to assess whether ω‐(o‐alkylphenyl)alkanoic acids form when pure compounds and complex triacylglycerol mixtures are heated with a fired clay. The results demonstrate that ω‐(o‐alkylphenyl)alkanoic acids are only produced following heating of unsaturated fatty acids (tri‐, di‐ and monounsaturated species) or complex unsaturated fatty acyl lipids at around 270°C. Heating saturated fatty acyl lipids does not yield ω‐(o‐alkylphenyl)alkanoic acids. Thus, when searching for evidence for the processing of marine derived animal fats in archaeological pottery vessels, it is essential that: ω‐(o‐alkylphenyl)alkanoic acids of carbon length C₁₈ and C₂₀ should be present, ideally with C₂₂ also detectable (if only in trace abundances), together with at least one of the three isoprenoid fatty acids (phytanic, pristanic or 4,8,12‐tetramethyltridecanoic acid).     

Portuguese Blue‐on‐Blue 16th–17th Century Pottery

Blue‐on‐blue (‘berettino’) sherds have appeared in numerous production and consumption archaeological excavations in Lisbon and other archaeological sites in Portugal (dated from the mid‐16th century to the beginning of the 17th century). The abundance of this interesting faience led us to compare it with similar pottery from other well‐known production centres in Italy, namely Liguria (Savona and Albisola), Spain (the Triana kilns) and the Low Countries. Differences in the diffraction patterns of the sherds' pastes from the four countries were observed. In most samples, cobalt blue silicate (cobalt olivine) was identified in the dark blue or light blue glazes through the use of micro‐Raman spectroscopy and diffuse reflectance spectra. A remarkable difference in the calcite contents of the Lisbon and Seville pottery sherds was observed, in accordance with previous observations of high calcite contents of Seville ceramics. A comparison was also made for all of the blue‐on‐blue sherds studied here with many other 16th–17th century sherds from Lisbon using bivariate plots of K/Si versus Ca/Si. Lisbon and Seville pottery behave very differently, whereas sherds from Italy and the Low Countries occupy intermediate positions.     

The Provenance of Red Figure Vases From Locri Epizephiri (Southern Italy): New Evidence by Chemical Analysis

Thirty‐nine samples of red figure pottery found at Locri Epizephiri were analysed for 18 chemical elements by inductively coupled plasma emission spectroscopy. The finds, dated from the end of the sixth to the fourth century bc , were assigned to Attic, Sicilian and Locrian workshops due to their style of execution. Prior to facing the archaeological questions, possible biases on sample classification due to variable firing conditions, or to alteration during burial, were investigated: the results supported the opportunity of a refiring pre‐treatment. Multivariate statistical treatment of the analytical data confirms the separation between Attic and non‐Attic samples; comparison with the composition of black gloss pottery suggests that all the non‐Attic red figure vases could be the output of Locrian workshops.     

Chemical Variability in Clays and Pottery from a Traditional Cooking Pot Production Village: Testing Assumptions in Pereruela*

This paper explores analytically the contemporary pottery‐making community of Pereruela (north‐west Spain) that produces cooking pots from a mixture of red clay and kaolin. Analyses by different techniques (XRF, NAA, XRD, SEM and petrography) showed an extremely high variability for cooking ware pottery produced in a single production centre, by the same technology and using local clays. The main source of chemical variation is related to the use of different red clays and the presence of non‐normally distributed inclusions of monazite. These two factors induce a high chemical variability, not only in the output of a single production centre, but even in the paste of a single pot, to an extent to which chemical compositions from one ‘workshop’, or even one ‘pot’, could be classified as having different provenances. The implications for the chemical characterization and for provenance studies of archaeological ceramics are addressed.     

Inductively coupled plasma emission spectroscopy and Postclassic Petén slipped pottery: an examination of pottery wares,social identity and trade*

ICP–ES analysis of the clay pastes of Postclassic (c. ad 850–1524) slipped pottery from the central Petén lakes region establishes chemical composition groups that provide information concerning manufacturing traditions and trading patterns. These data demonstrate that manufacturing traditions and trading patterns change throughout the Postclassic period, reflecting possible socio‐political alliances as different ethnic groups migrated to and from the Yucatán peninsula into the central Petén lakes region. The chemical composition groups also demonstrate that some manufacturing traditions imitate those from the Late Classic period and that some clay sources were used throughout the Postclassic period for multiple ceramic groups.     

POTENTIAL MAGNETIC SUSCEPTIBILITY AND FRACTIONAL CONVERSION STUDIES OF ARCHAEOLOGICAL SOILS AND SEDIMENTS*

Potential magnetic susceptibility (χ_MAX) and, hence, fractional conversion (χ_CONV) are shown to be critical in interpreting low‐frequency mass‐specific magnetic susceptibility (χ_LF) data. Results presented from 29 sites in the UK and one in Hungary encompass six types of investigation: Quaternary sedimentary stratigraphies, archaeological contexts, surveys of old ground surfaces, topsoil surveys of lithic scatter sites, topsoil prospection surveys and ‘natural’ topsoils. The findings highlight the wide range of χ_MAX values that may be encountered; identify factors affecting χ_MAX; demonstrate that χ_CONV provides a measure of enhancement resulting from burning; and identify environments in which χ_LF analysis is likely to be problematic.     

The Hellenistic and Roman Syracuse (Sicily) Fine Pottery Production Explored by Chemical and Petrographic Analysis

The chemical composition and petrographic features of 51 samples of fine pottery selected from the archaeological site of Syracuse have been established by means of optical microscopy and X‐ray fluorescence spectrometry, with the aim of creating a reference group for the ceramics produced in this important Greek colony during the Hellenistic–Roman period. This reference group is constrained by the analysis of six kiln wasters and of raw materials outcropping in the studied area. Among the studied findings, the main part is assignable imputably to local production, while some specimens probably come from Greece and other colonies (Messina and Gela). The Syracuse fine pottery is characterized by inclusions formed mainly by quartz and micaceous and fossiliferous groundmass. The used pastes were more or less purified through the removal of the sandy‐to‐coarse silty granulometric fraction. The multivariate statistical analysis of chemical data permits the identification of production at Syracuse on the basis of comparison with the kiln wasters and the Plio‐Pleistocene clays.     

THE PROVENANCE AND PRODUCTION TECHNOLOGY OF BRONZE AGE AND IRON AGE POTTERY FROM TELL MISHRIFEH/QATNA (SYRIA)*

This work deals with the archaeometric study of the Bronze Age and Iron Age pottery from Tell Mishrifeh/Qatna (central‐western Syria), where the complete cycle of ceramic production is well documented. Petrographic, chemical and diffractometric analyses were carried out on both potsherds and a clayey material found in a separation basin within the area of the workshops. Petrographic groups were defined and maximum firing temperatures and redox firing conditions were estimated, providing constraints on identifying the production technology and its evolution with time. The studied potsherds turned out to be locally produced, with only a few cases of possible similarities with those described for other localities along the Orontes Valley, and in a couple of cases with evidence of pottery exchange.