Permeability of the Mercia Mudstone: suitability as caprock to carbon capture and storage sites

The Upper Triassic Mercia Mudstone is the caprock to potential carbon capture and storage (CCS) sites in porous and permeable Lower Triassic Sherwood Sandstone reservoirs and aquifers in the UK (primarily offshore). This study presents direct measurements of vertical (k_v) and horizontal (k_h) permeability of core samples from the Mercia Mudstone across a range of effective stress conditions to test their caprock quality and to assess how they will respond to changing effective stress conditions that may occur during CO₂ injection and storage. The Mercia samples analysed were either clay‐rich (muddy) siltstones or relatively clean siltstones cemented by carbonate and gypsum. Porosity is fairly uniform (between 7.4 and 10.7%). Porosity is low either due to abundant depositional illite or abundant diagenetic carbonate and gypsum cements. Permeability values are as low as 10^?20 m² (10nD), and therefore, the Mercia has high sealing capacity. These rocks have similar horizontal and vertical permeabilities with the highest k_h/k_v ratio of 2.03 but an upscaled k_h/k_v ratio is 39, using the arithmetic mean of k_h and the harmonic mean of k_v. Permeability is inversely related to the illite clay content; the most clay‐rich (illite‐rich) samples represent very good caprock quality; the cleaner Mercia Mudstone samples, with pore‐filling carbonate and gypsum cements, represent fair to good caprock quality. Pressure sensitivity of permeability increases with increasing clay mineral content. As pore pressure increases during CO₂ injection, the permeability of the most clay‐rich rocks will increase more than carbonate‐ and gypsum‐rich rocks, thus decreasing permeability heterogeneity. The best quality Mercia Mudstone caprock is probably not geochemically sensitive to CO₂ injection as illite, the cause of the lowest permeability, is relatively stable in the presence of CO₂–water mixtures.     

Carbon dioxide controlled earthquake distribution pattern in the NW Bohemian swarm earthquake region,western Eger Rift,Czech Republic – gas migration in the crystalline basement

The ascent of magmatic carbon dioxide in the western Eger (Oh?e) Rift is interlinked with the fault systems of the Variscian basement. In the Cheb Basin, the minimum CO₂ flux is about 160 m³ h^?1, with a diminishing trend towards the north and ceasing in the main epicentral area of the Northwest Bohemian swarm earthquakes. The ascending CO₂ forms Ca‐Mg‐HCO₃ type waters by leaching of cations from the fault planes and creates clay minerals, such as kaolinite, as alteration products on affected fault planes. These mineral reactions result in fault weakness and in hydraulically interconnected fault network. This leads to a decrease in the friction coefficient of the Coulomb failure stress (CFS) and to fault creep as stress build‐up cannot occur in the weak segments. At the transition zone in the north of the Cheb Basin, between areas of weak, fluid conductive faults and areas of locked faults with frictional strength, fluid pressure can increase resulting in stress build‐up. This can trigger strike‐slip swarm earthquakes. Fault creep or movements in weak segments may support a stress build‐up in the transition area by transmitting fluid pressure pulses. Additionally to fluid‐driven triggering models, it is important to consider that fluids ascending along faults are CO₂‐supersaturated thus intensifying the effect of fluid flow. The enforced flow of CO₂‐supersaturated fluids in the transitional zone from high to low permeability segments through narrowings triggers gas exsolution and may generate pressure fluctuations. Phase separation starts according to the phase behaviour of CO₂‐H₂O systems in the seismically active depths of NW Bohemia and may explain the vertical distribution of the seismicity. Changes in the size of the fluid transport channels in the fault systems caused, or superimposed, by fault movements, can produce fluid pressure increases or pulses, which are the precondition for triggering fluid‐induced swarm earthquakes.     

Gas breakthrough experiments on pelitic rocks: comparative study with N2, CO2 and CH4

The capillary‐sealing efficiency of intermediate‐ to low‐permeable sedimentary rocks has been investigated by N₂, CO₂ and CH₄ breakthrough experiments on initially fully water‐saturated rocks of different lithological compositions. Differential gas pressures up to 20 MPa were imposed across samples of 10–20 mm thickness, and the decline of the differential pressures was monitored over time. Absolute (single‐phase) permeability coefficients (k_abs), determined by steady‐state fluid flow tests, ranged between 10^?22 and 10^?15 m². Maximum effective permeabilities to the gas phase k_eff(max), measured after gas breakthrough at maximum gas saturation, extended from 10^?26 to 10^?18 m². Because of re‐imbibition of water into the interconnected gas‐conducting pore system, the effective permeability to the gas phase decreases with decreasing differential (capillary) pressure. At the end of the breakthrough experiments, a residual pressure difference persists, indicating the shut‐off of the gas‐conducting pore system. These pressures, referred to as the ‘minimum capillary displacement pressures’ (P_d), ranged from 0.1 up to 6.7 MPa. Correlations were established between (i) absolute and effective permeability coefficients and (ii) effective or absolute permeability and capillary displacement pressure. Results indicate systematic differences in gas breakthrough behaviour of N₂, CO₂ and CH₄, reflecting differences in wettability and interfacial tension. Additionally, a simple dynamic model for gas leakage through a capillary seal is presented, taking into account the variation of effective permeability as a function of buoyancy pressure exerted by a gas column underneath the seal.     

The effect of deformation on permeability development in anhydrite and implications for caprock integrity during geological storage of CO2

Geological storage of CO₂ in depleted oil and gas reservoirs is one of the most promising options to reduce atmospheric CO₂ concentrations. Of great importance to CO₂ mitigation strategies is maintaining caprock integrity. Worldwide many current injection sites and potential storage sites are overlain by anhydrite‐bearing seal formations. However, little is known about the magnitude of the permeability change accompanying dilatation and failure of anhydrite under reservoir conditions. To this extent, we have performed triaxial compression experiments together with argon gas permeability measurements on Zechstein anhydrite, which caps many potential CO₂ storage sites in the Netherlands. Our experiments were performed at room temperature at confining pressures of 3.5–25 MPa. We observed a transition from brittle to semi‐brittle behaviour over the experimental range, and peak strength could be described by a Mogi‐type failure envelope. Dynamic permeability measurements showed a change from ‘impermeable’ (<10^?21 m²) to permeable (10^?16 to 10^?19 m²) as a result of mechanical damage. The onset of measurable permeability was associated with an increase in the rate of dilatation at low pressures (3.5–5 MPa), and with the turning point from compaction to dilatation in the volumetric versus axial strain curve at higher pressures (10–25 MPa). Sample permeability was largely controlled by the permeability of the shear faults developed. Static, postfailure permeability decreased with increasing effective mean stress. Our results demonstrated that caprock integrity will not be compromised by mechanical damage and permeability development. Geofluids (2010) 10 , 369–387     

Effective gas permeability of Tight Gas Sandstones as a function of capillary pressure – a non‐steady‐state approach

Single‐ and two‐phase (gas/water) fluid transport in tight sandstones has been studied in a series of permeability tests on core plugs of nine tight sandstones of the southern North Sea. Absolute (Klinkenberg‐corrected) gas permeability coefficients (k_gas__inf) ranged between 3.8 × 10^?16 and 6.2 × 10^?19 m² and decreased with increasing confining pressure (10–30 MPa) by a factor 3–5. Klinkenberg‐corrected (intrinsic) gas permeability coefficients were consistently higher by factors from 1.4 to 10 than permeability coefficients determined with water. Non‐steady‐state two‐phase (He/water) flow experiments conducted up to differential pressures of 10 MPa document the dynamically changing conductivity for the gas phase, which is primarily capillary‐controlled (drainage and imbibition). Effective gas permeability coefficients in the two‐phase flow tests ranged between 1.1 × 10^?17 and 2.5 × 10^?22 m², corresponding to relative gas permeabilities of 0.03% and 10%. In the early phase of the nonstationary flow regime (before establishment of steady‐state conditions), they may be substantially (>50%) lower. Effective gas permeability measurements are affected by the following factors: (i) Capillary‐controlled drainage/imbibition, (ii) viscous–dynamic effects (iii) and slip flow.     

Analytical and numerical models of hydrothermal fluid flow at fault intersections

Fault intersections are the locus of hot spring activity and Carlin‐type gold mineralization within the Basin and Range, USA. Analytical and numerical solutions to Stokes equation suggest that peak fluid velocities at fault intersections increase between 20% and 47% when fracture apertures have identical widths but increase by only about 1% and 8% when aperture widths vary by a factor of 2. This suggests that fault zone intersections must have enlarged apertures. Three‐dimensional finite element models that consider intersecting 10‐ to 20‐m wide fault planes resulted in hot spring activity being preferentially located at fault zone intersections when fault zones were assigned identical permeabilities. We found that the onset of convection at the intersections of the fault zones occurred in our hydrothermal model over a narrow permeability range between 5 × 10^?13 and 7 × 10^?13 m². Relatively high vertical fluid velocities (0.3–3 m year^?1) extended away from the fault intersections for about 0.5–1.5 km. For the boundary conditions and fault plane dimensions used, peak discharge temperatures of 112°C at the water table occurred with an intermediate fault zone permeability of 5 × 10^?13 m². When fault plane permeability differed by a factor of 2 or more, the locus of hot spring activity shifted away from the intersections. However, increasing the permeability at the core of the fault plane intersection by 40% shifted the discharge back to the intersections. When aquifer units were assigned a permeability value equal to those of the fault planes, convective rolls developed that extend about 3 km laterally along the fault plane and into the adjacent aquifer.     

Gas breakthrough experiments on fine-grained sedimentary rocks

The capillary sealing efficiency of fine‐grained sedimentary rocks has been investigated by gas breakthrough experiments on fully water saturated claystones and siltstones (Boom Clay from Belgium, Opalinus Clay from Switzerland and Tertiary mudstone from offshore Norway) of different lithological compositions. Sand contents of the samples were consistently below 12%, major clay minerals were illite and smectite. Porosities determined by mercury injection lay between 10 and 30% while specific surface areas determined by nitrogen adsorption (BET method) ranged from 20 to 48 m² g ^{? 1}. Total organic carbon contents were below 2%. Prior to the gas breakthrough experiments the absolute (single phase) permeability (k_abs) of the samples was determined by steady state flow tests with water or NaCl brine. The k_abs values ranged between 3 and 550 nDarcy (3 × 10^?21 and 5.5 × 10^?19 m²). The maximum effective permeability to the gas‐phase (k_eff) measured after gas breakthrough on initially water‐saturated samples extended from 0.01 nDarcy (1 × 10^?23 m²) up to 1100 nDarcy (1.1 × 10^?18 m²). The residual differential pressures after re‐imbibition of the water phase, referred to as the ‘minimum capillary displacement pressures’ (P_d), ranged from 0.06 to 6.7 MPa. During the re‐imbibition process the effective permeability to the gas phase decreases with decreasing differential pressure. The recorded permeability/pressure data were used to derive the pore size distribution (mostly between 8 and 60 nm) and the transport porosity of the conducting pore system (10^‐5–10^‐2%). Correlations could be established between (i) absolute permeability coefficients and the maximum effective permeability coefficients and (ii) effective or absolute permeability coefficients and capillary sealing efficiency. No correlation was found between the capillary displacement pressures determined from gas breakthrough experiments and those derived theoretically by mercury injection.     

Effects of episodic fluid flow on hydrocarbon migration in the Newport‐Inglewood Fault Zone,Southern California

Fault permeability may vary through time due to tectonic deformations, transients in pore pressure and effective stress, and mineralization associated with water‐rock reactions. Time‐varying permeability will affect subsurface fluid migration rates and patterns of petroleum accumulation in densely faulted sedimentary basins such as those associated with the borderland basins of Southern California. This study explores the petroleum fluid dynamics of this migration. As a multiphase flow and petroleum migration case study on the role of faults, computational models for both episodic and continuous hydrocarbon migration are constructed to investigate large‐scale fluid flow and petroleum accumulation along a northern section of the Newport‐Inglewood fault zone in the Los Angeles basin, Southern California. The numerical code solves the governing equations for oil, water, and heat transport in heterogeneous and anisotropic geologic cross sections but neglects flow in the third dimension for practical applications. Our numerical results suggest that fault permeability and fluid pressure fluctuations are crucial factors for distributing hydrocarbon accumulations associated with fault zones, and they also play important roles in controlling the geologic timing for reservoir filling. Episodic flow appears to enhance hydrocarbon accumulation more strongly by enabling stepwise build‐up in oil saturation in adjacent sedimentary formations due to temporally high pore pressure and high permeability caused by periodic fault rupture. Under assumptions that fault permeability fluctuate within the range of 1–1000 millidarcys (10^?15–10^?12 m²) and fault pressures fluctuate within 10–80% of overpressure ratio, the estimated oil volume in the Inglewood oil field (approximately 450 million barrels oil equivalent) can be accumulated in about 24 000 years, assuming a seismically induced fluid flow event occurs every 2000 years. This episodic petroleum migration model could be more geologically important than a continuous‐flow model, when considering the observed patterns of hydrocarbons and seismically active tectonic setting of the Los Angeles basin.     

Exploring the potential linkages between oil‐field brine reinjection,crystalline basement permeability,and triggered seismicity for the Dagger Draw Oil field,southeastern New Mexico,USA, using hydrologic modeling

We used hydrologic models to explore the potential linkages between oil‐field brine reinjection and increases in earthquake frequency (up to M_d 3.26) in southeastern New Mexico and to assess different injection management scenarios aimed at reducing the risk of triggered seismicity. Our analysis focuses on saline water reinjection into the basal Ellenburger Group beneath the Dagger Draw Oil field, Permian Basin. Increased seismic frequency (>M_d 2) began in 2001, 5 years after peak injection, at an average depth of 11 km within the basement 15 km to the west of the reinjection wells. We considered several scenarios including assigning an effective or bulk permeability value to the crystalline basement, including a conductive fault zone surrounded by tighter crystalline basement rocks, and allowing permeability to decay with depth. We initially adopted a 7 m (0.07 MPa) head increase as the threshold for triggered seismicity. Only two scenarios produced excess heads of 7m five years after peak injection. In the first, a hydraulic diffusivity of 0.1 m² s^?1 was assigned to the crystalline basement. In the second, a hydraulic diffusivity of 0.3 m² s^?1 was assigned to a conductive fault zone. If we had considered a wider range of threshold excess heads to be between 1 and 60 m, then the range of acceptable hydraulic diffusivities would have increased (between 0.1–0.01 m² s^?1 and 1–0.1 m² s^?1 for the bulk and fault zone scenarios, respectively). A permeability–depth decay model would have also satisfied the 5‐year time lag criterion. We also tested several injection management scenarios including redistributing injection volumes between various wells and lowering the total volume of injected fluids. Scenarios that reduced computed excess heads by over 50% within the crystalline basement resulted from reducing the total volume of reinjected fluids by a factor of 2 or more.     

Geometry‐coupled reactive fluid transport at the fracture scale: application to CO2 geologic storage

Water acidification follows CO₂ injection and leads to reactive fluid transport through pores and rock fractures, with potential implications to reservoirs and wells in CO₂ geologic storage and enhanced oil recovery. Kinetic rate laws for dissolution reactions in calcite and anorthite are combined with the Navier‐Stokes law and advection–diffusion transport to perform geometry‐coupled numerical simulations in order to study the evolution of chemical reactions, species concentration, and fracture morphology. Results are summarized as a function of two dimensionless parameters: the Damköhler number Da which is the ratio between advection and reaction times, and the transverse Peclet number Pe defined as the ratio between the time for diffusion across the fracture and the time for advection along the fracture. Reactant species are readily consumed near the inlet in a carbonate reservoir when the flow velocity is low (low transverse Peclet number and Da > 10^?1). At high flow velocities, diffusion fails to homogenize the concentration field across the fracture (high transverse Peclet number Pe > 10^?1). When the reaction rate is low as in anorthite reservoirs (Da < 10^?1), reactant species are more readily transported toward the outlet. At a given Peclet number, a lower Damköhler number causes the flow channel to experience a more uniform aperture enlargement along the length of the fracture. When the length‐to‐aperture ratio is sufficiently large, say l/d > 30, the system response resembles the solution for 1D reactive fluid transport. A decreased length‐to‐aperture ratio slows the diffusive transport of reactant species to the mineral fracture surface, and analyses of fracture networks must take into consideration both the length and slenderness of individual fractures in addition to Pe and Da numbers.     

The upper continental crust, an aquifer and its fluid: hydaulic and chemical data from 4 km depth in fractured crystalline basement rocks at the KTB test site

Detailed information on the hydrogeologic and hydraulic properties of the deeper parts of the upper continental crust is scarce. The pilot hole of the deep research drillhole (KTB) in crystalline basement of central Germany provided access to the crust for an exceptional pumping experiment of 1‐year duration. The hydraulic properties of fractured crystalline rocks at 4 km depth were derived from the well test and a total of 23100 m³ of saline fluid was pumped from the crustal reservoir. The experiment shows that the water‐saturated fracture pore space of the brittle upper crust is highly connected, hence, the continental upper crust is an aquifer. The pressure–time data from the well tests showed three distinct flow periods: the first period relates to wellbore storage and skin effects, the second flow period shows the typical characteristics of the homogeneous isotropic basement rock aquifer and the third flow period relates to the influence of a distant hydraulic border, probably an effect of the Franconian lineament, a steep dipping major thrust fault known from surface geology. The data analysis provided a transmissivity of the pumped aquifer T = 6.1 × 10^?6 m² sec^?1, the corresponding hydraulic conductivity (permeability) is K = 4.07 × 10^?8 m sec^?1 and the computed storage coefficient (storativity) of the aquifer of about S = 5 × 10^?6. This unexpected high permeability of the continental upper crust is well within the conditions of possible advective flow. The average flow porosity of the fractured basement aquifer is 0.6–0.7% and this range can be taken as a representative and characteristic values for the continental upper crust in general. The chemical composition of the pumped fluid was nearly constant during the 1‐year test. The total of dissolved solids amounts to 62 g l^?1 and comprise mainly a mixture of CaCl₂ and NaCl; all other dissolved components amount to about 2 g l^?1. The cation proportions of the fluid (X_Ca approximately 0.6) reflects the mineralogical composition of the reservoir rock and the high salinity results from desiccation (H₂O‐loss) due to the formation of abundant hydrate minerals during water–rock interaction. The constant fluid composition suggests that the fluid has been pumped from a rather homogeneous reservoir lithology dominated by metagabbros and amphibolites containing abundant Ca‐rich plagioclase.     

Permeability changes in simulated granite faults during and after frictional sliding

Thermal–hydrological–mechanical coupling processes suggest that fault permeability should undergo dynamic change as a result of seismic slip. In igneous rocks, a fault's slip surface may have much higher permeability than the surrounding rock matrix and therefore operate as a conduit for fluids. We conducted laboratory experiments to investigate changes in fracture permeability (or transmissivity) of a fault in granite due to shear slip and cyclic heating and cooling. Our experiments showed that high initial fracture transmissivity (>10^?18 m³) was associated with a high friction coefficient and that transmissivity decreased during slip. We propose that this reduction in transmissivity reflects the presence of gouge in fracture voids, increasing the area of contact in the fault plane and reducing the hydraulic aperture. In contrast, when initial fracture transmissivity was low (<10^?18 m³), we observed that friction was lower and transmissivity increased during slip. The high transmissivity and high friction may be explained by large areas of bare rock being in contact on the slip surface. Slip velocity had little influence on the evolution of permeability, probably because gouge produced at different slip velocities had similar grain size distributions, or because gouge leaked from the slip surface. Transmissivity decreased with increasing temperature in heating tests, probably due to thermal expansion increasing normal stress on the fracture. Frictional heating did not influence transmissivity during the shearing tests.     

An exhumed palaeo-hydrocarbon migration fairway in a faulted carrier system, Entrada Sandstone of SE Utah, USA

The Moab Anticline, east‐central Utah, is an exhumed hydrocarbon palaeo‐reservoir which was supplied by hydrocarbons that migrated from the Moab Fault up‐dip towards the crest of the structure beneath the regional seal of the Tidwell mudstone. Iron oxide reduction in porous, high permeability aeolian sandstones records the secondary migration of hydrocarbons, filling of traps against small sealing faults and spill pathways through the Middle Jurassic Entrada Sandstone. Hydrocarbons entered the Entrada Sandstone carrier system from bends and other leak points on the Moab Fault producing discrete zones of reduction that extend for up to 400 m from these leak points. They then migrated in focused stringers, 2–5 m in height, to produce accumulations on the crest of the anticline. Normal faults on the anticline were transient permeability barriers to hydrocarbon migration producing a series of small compartmentalized accumulations. Exsolution of CO₂ as local fault seals were breached resulted in calcite cementation on the up‐dip side of faults. Field observations on the distribution of iron oxide reduction and calcite cements within the anticline indicate that the advancing reduction fronts were affected neither by individual slip bands in damage zones around faults nor by small faults with sand: sand juxtapositions. Faults with larger throws produced either sand: mudstone juxtapositions or sand: sand contacts and fault zones with shale smears. Shale‐smeared fault zones provided seals to the reducing fluid which filled the structural traps to spill points.     

Modelling the Lost City hydrothermal field: influence of topography and permeability structure

The Lost City hydrothermal field (LCHF) is hosted in serpentinite at the crest of the Atlantis Massif, an oceanic core complex close to the mid‐Atlantic Ridge. It is remarkable for its longevity and for venting low‐temperature (40–91°C) alkaline fluids rich in hydrogen and methane. IODP Hole U1309D, 5 km north of the LCHF, penetrated 1415 m of gabbroic rocks and contains a near‐conductive thermal gradient close to 100°C km^?1. This is remarkable so close to an active hydrothermal field. We present hydrothermal modelling using a topographic profile through the vent field and IODP site U1309. Long‐lived circulation with vent temperatures similar to the LCHF can be sustained at moderate permeabilities of 10^?14 to 10^?15 m² with a basal heatflow of 0.22 W m^?2. Seafloor topography is an important control, with vents tending to form and remain in higher topography. Models with a uniform permeability throughout the Massif cannot simultaneously maintain circulation at the LCHF and the near‐conductive gradient in the borehole, where permeabilities <10^?16 m² are required. A steeply dipping permeability discontinuity between the LCHF and the drill hole is required to stabilize venting at the summit of the massif by creating a lateral conductive boundary layer. The discontinuity needs to be close to the vent site, supporting previous inferences that high permeability is most likely produced by faulting related to the transform fault. Rapid increases in modelled fluid temperatures with depth beneath the vent agree with previous estimates of reaction temperature based on geochemical modelling.     

Migration of metamorphic CO2 into a coal seam: a natural analog study to assess the long‐term fate of CO2 in Coal Bed Carbon Capture,Utilization, and Storage Projects

This study assesses the displacement of coalbed methane by CO₂ migration along a fault into the coal seam in the Yaojie coalfield. Coal and gas samples were collected continuously at various distances in NO.2 coal seam from F19 fault. Vitrinite reflectance, maceral, and pore distributions and proximate analysis of fourteen coal samples were performed. Gas components, concentrations, carbon isotopes of 28 gas samples were determined. We examined the coal–gas trace characteristics of coalbed methane displaced away from the fault by CO₂ injection after geological ages. From east to west, away from the F19 fault, the CO₂ concentration decreased, whereas the CH₄ concentration increased gradually. The δ¹³C values for CO₂ varied between ?9.94‰ and 1.12‰, suggesting a metamorphic origin. A wider range of values (from ?9.94‰ to 20‰) was associated with the mixing of microbial carbon dioxide, isotopic fractionation during CO₂ migration through the microporous structures of coals, and/or carbon isotope fractionation during gas–water exchange and dissolution of CO₂. Away from the F19 fault, the volumes of micropores, mesopores and macropores decrease gradually. The Dubinin–Radushkevich (DR) micropore volume decreased from 0.0059 to 0.0037 cm³ g^‐1, and the mesopore and macropore volumes decreased from 0.066 to 0.026 cm³ g^‐1. The CO₂ injection can mobilize aromatic hydrocarbons and mineral matter from coal matrix, resulting in the decrease in the absorption peak intensity for coal samples after supercritical CO₂ treatment, which indicates that chemical reactions occur between coal and CO₂, not only physical adsorption.     

Geological setting, nature of ore fluids and sulphur isotope geochemistry of the Fu Ning Carlin-type gold deposits, Yunnan Province, China

Carlin‐type gold deposits in southern China are present in Palaeozoic to Mesozoic siliciclastic and carbonate rocks. The border region of Yunnan, Guizhou and Guangxi Provinces contains gold deposits on the south‐western margin of the Pre‐Cambrian South China Craton in south‐eastern Yunnan Province. The Fu Ning gold deposits host epigenetic, micron‐sized disseminated gold in: (i) Middle Devonian (D₁p) black carbonaceous mudstone at the Kuzhubao gold deposit and (ii) fault breccia zones at the contact between Triassic gabbro (β ) and the Devonian mudstone (D₁p) at the Bashishan gold deposit. The deposits are associated with zones of intense deformation with enhanced permeability and porosity that focused hydrothermal fluid flow, especially where low‐angle N‐S striking thrust faults are cut by NW striking strike‐slip and/or NE striking normal faults. Major sulphide ore minerals in the Fu Ning gold deposits are pyrite, arsenopyrite, arsenic‐rich pyrite, stibnite and minor iron‐poor sphalerite. Gangue minerals are quartz, sericite, calcite, ankerite and chlorite. Hypogene ore grades range from 1 to 7 g t^?1 Au and up to 18 g t^?1 Au at the Kuzhubao gold deposit and are generally less than 3 g t^?1 Au at the Bashishan gold deposit. Sub‐microscopic gold mineralization is associated with finely disseminated arsenic‐rich pyrite in the Stage III mineral assemblage. Two types of primary fluid inclusions have been recorded: Type I liquid–vapour inclusions with moderate‐to‐high liquid/vapour ratios, and Type II inclusions containing moderate liquid/vapour ratios with CO₂ as determined from laser Raman analysis. Temperature of homogenization (T_h) data collected from these primary fluid inclusions in gold‐ore Stage III quartz ranged from 180 to 275°C at the Kuzhubao gold deposit and 210 to 330°C at the Bashishan gold deposit. Salinity results indicate that there were possibly two fluids present during gold deposition, including: (i) an early fluid with 0.8–6.5 wt.% NaCl equivalent, similar to salinity in shear‐zone‐hosted gold deposits with metamorphic derived fluids; and (ii) a late fluid with 11.8–13.4 wt.% NaCl equivalent, indicating possible derivation from connate waters and/or brine sources. CO₂ and trace CH₄ were only detected by laser Raman spectrometry in gold‐ore‐stage primary fluid inclusions. Results of sulphur isotope studies showed that δ³⁴S values for pyrite and arsenopyrite associated with gold‐ore mineralization during Stage III at the Kuzhubao and Bashishan gold deposits are isotopically similar and moderately heavy with a range from +9 to +15 per mil, and also fall into the range of δ³⁴S values reported for Carlin‐type gold deposits. Sulphur isotopes suggest that the Fu Ning gold deposits were formed from connate waters and/or basinal brines. Fluid geochemistry data from the Fu Ning gold deposits suggest a Carlin‐type genetic model, involving fluid mixing between: (i) deep CO₂‐rich metamorphic fluids, (ii) moderately saline, reduced connate waters and/or basinal brines; and (iii) evolved meteoric waters.     

Stress‐dependent transport properties of fractured arkosic sandstone

We measure the fluid transport properties of microfractures and macrofractures in low‐porosity polyphase sandstone and investigate the controls of in situ stress state on fluid flow conduits in fractured rock. For this study, the permeability and porosity of the Punchbowl Formation sandstone, a hydrothermally altered arkosic sandstone, were measured and mapped in stress space under intact, microfractured, and macrofractured deformation states. In contrast to crystalline and other sedimentary rocks, the distributed intragranular and grain‐boundary microfracturing that precedes macroscopic fracture formation has little effect on the fluid transport properties. The permeability and porosity of microfractured and intact sandstone depend strongly on mean stress and are relatively insensitive to differential stress and proximity to the frictional sliding envelope. Porosity variations occur by elastic pore closure with intergranular sliding and pore collapse caused by microfracturing along weakly cemented grain contacts. The macroscopic fractured samples are best described as a two‐component system consisting (i) a tabular fracture with a 0.5‐mm‐thick gouge zone bounded by 1 mm thick zones of concentrated transgranular and intragranular microfractures and (ii) damaged sandstone. Using bulk porosity and permeability measurements and finite element methods models, we show that the tabular fracture is at least two orders of magnitude more permeable than the host rock at mean stresses up to 90 MPa. Further, we show that the tabular fracture zone dilates as the stress state approaches the friction envelope resulting in up to a three order of magnitude increase in fracture permeability. These results indicate that the enhanced and stress‐sensitive permeability in fault damage zones and sedimentary basins composed of arkosic sandstones will be controlled by the distribution of macroscopic fractures rather than microfractures.     

Isotopic and petrological evidence of fluid–rock interaction at a Tethyan ocean–continent transition in the Alps: implications for tectonic processes and carbon transfer during early ocean formation

We report overprinting stable isotope evidence of fluid–rock interaction below two detachment faults along which mantle rocks were exhumed to the seafloor, between the respective landward and seaward limits of oceanic and continental crust, at a Tethyan ocean–continent transition (OCT). This OCT, which is presently exposed in the Tasna nappe (south‐eastern Switzerland) is considered an on‐land analogue of the well‐studied Iberian OCT. We compare our results with the fault architecture (fault core–damage zone–protolith) described by Caine et al. [Geology (1996) Vol. 24, pp. 1025–1028]. We confirm the existence of a sharp boundary between the fault core and damage zone based on isotopic data, but the boundary between the damage zone and protolith is gradational. We identify evidence for: (1) pervasive isotopic modification to 8.4 ± 0.1‰ which accompanied or post‐dated serpentinization of these mantle rocks at an estimated temperature of 67–109°C, (2) either (i) partial isolation of some highly strained regions [fault core(s) and mylonite] from this pervasive isotopic modification, because of permeability reduction (Caine et al.) or (ii) subsequent isotopic modification caused by structurally channelled flow of warm fluids within these highly strained regions, because of permeability enhancement, and (3) isotopic modification, which is associated with extensive calcification at T = 54–100°C, primarily beneath the younger of the two detachment faults and post‐dating initial serpentinization. By comparing the volumetric extent of calcification with an experimentally verified model for calcite precipitation in veins, we conclude that calcification could have occurred in response to seawater infiltration, with a calculated flux rate of 0.1–0.2 m year^?1 and a minimum duration of 0.2–4.0 × 10⁴ years. The associated time‐averaged uptake flux of carbon during this period was 8–120 mol m^?2 year^?1. By comparison with the estimated area of exhumed mantle rocks at the Iberian OCT, we calculate a maximum annual uptake flux for carbon of 2–30 Tg year^?1. This is an order of magnitude greater than that for carbon exchange at the mid‐ocean ridges and 0.1–1.4% of the global oceanic uptake flux for carbon.     

Fluid inclusion and stable isotope constraints on the genesis of the Jian copper deposit,Sanandaj–Sirjan metamorphic zone,Iran

The Jian copper deposit, located on the eastern edge of the Sanandaj–Sirjan metamorphic zone, southwest of Iran, is contained within the Surian Permo‐Triassic volcano‐sedimentary complex. Retrograde metamorphism resulted in three stages of mineralization (quartz ± sulfide veins) during exhumation of the Surian metamorphic complex (Middle Jurassic time; 159–167 Ma), and after the peak of the metamorphism (Middle to Late Triassic time; approximately 187 Ma). The early stage of mineralization (stage 1) is related to a homogeneous H₂O–CO₂ (XCO₂ > 0.1) fluid characterized by moderate salinity (<10 wt.% NaCl equivalent) at high temperature and pressure (>370°C, >3 kbar). Early quartz was followed by small amounts of disseminated fine‐grained pyrite and chalcopyrite. Most of the main‐ore‐stage (stage 2) minerals, including chalcopyrite, pyrite and minor sphalerite, pyrrhotite, and galena, precipitated from an aqueous‐carbonic fluid (8–18 wt.% NaCl equivalent) at temperatures ranging between 241 and 388°C during fluid unmixing process (CO₂ effervescence). Fluid unmixing in the primary carbonaceous fluid at pressures of 1.5–3 kbar produced a high XCO₂ (>0.05) and a low XCO₂ (<0.01) aqueous fluid in ore‐bearing quartz veins. Oxygen and hydrogen isotope compositions suggest mineralization by fluids derived from metamorphic dehydration (δ¹⁸O_fluid = +7.6 to +10.7‰ and δD = ?33.1 to ?38.5‰) during stage 2. The late stage (stage 3) is related to a distinct low salinity (1.5–8 wt.% NaCl equivalent) and temperatures of (120–230°C) aqueous fluid at pressures below 1.5 kbar and the deposition of post‐ore barren quartz veins. These fluids probably derived from meteoric waters, which circulated through the metamorphic pile at sufficiently high temperatures and acquire the characteristics of metamorphic fluids (δ¹⁸O_fluid = +4.7 to +5.1‰ and δD = ?52.3 to ?53.9‰) during waning stages of the postearly Cimmerian orogeny in Surian complex. The sulfide‐bearing quartz veins are interpreted as a small‐scale example of redistribution of mineral deposits by metamorphic fluids. This study suggests that mineralization at the Jian deposit is metamorphogenic in style, probably related to a deep‐seated mesothermal system.     

The October 2008 Nový Kostel earthquake swarm and its gas geochemical precursor

A gas geochemical precursor anomaly was identified prior to the October 2008 Nový Kostel (Czech Republic) earthquake swarm with a peak magnitude M_L of 3.8. This anomaly was observed as a deviation of CO₂ concentrations from the long‐term annual CO₂ concentration trend in the gas extracted from the scree at the Nový Kostel and Old?i?ská gas monitoring stations, which are directly above the Plesná valley‐Po?átky and Mariánské Lázně fault systems. Both sites are located within the major focal zone of the NW Bohemian swarm earthquake region at the northern edge of the Cheb Basin. A decrease in CO₂ concentration started at Nový Kostel in September 2008, 17 days before the swarm, opposite to the usually increasing annual trend in the autumn period, and ended with a nearly coseismic drop immediately prior to the onset of the first swarm. The CO₂ concentrations at Old?i?ská, deviating from the annual trend, did not further increase after August 2008. The calculated horizontal strain field, based on the data of two permanent Global Navigation Satellite Systems stations, proved there was horizontal compression in this period. The increasing compression along the Plesná valley‐Po?átky and Mariánské Lázně fault systems during the stress build‐up reduced the fault permeability prior to this earthquake swarm as indicated by the decrease in CO₂ concentration. The 17‐day duration of the earthquake precursor at Nový Kostel and about 65 days at Old?i?ská lie within the range of the precursor times that are hypothesized worldwide for an M_L = 3.8 earthquake. The nature of earthquake precursors and their origin are discussed, for example, as an indication of changed fault permeability by stress build‐up in the case of the Nový Kostel swarm earthquake precursor or as fault opening in other cases.